In this paper, limit analyses of cylindrical shells with a circular opening under the action of combined axial force and bending moment at the ends are carried out using both finite element methods and the approximate analytical lower-bound limit load of the weakest section of the cylinder. The finite element calculations consist of elastic-plastic and elastic compensation methods using an ANSYS suite of programs. The results obtained by the finite element methods are then compared with the approximate analytical lower-bound limit load of the cylinder, and the correlation between them is discussed.
Van DykeP.Stresses about a circular hole in a cylindrical shellAm. Inst. Aeronaut. Astronaut. J., 1963, 3 (9), 1733–1742.
4.
DinnoK. S.GillS.S.The effect of the circumferential bending moment and change of circumferential curvature on the calculation of the limit pressure of symmetrically loaded shells of revolutionInt. J. Mech. Sci., 1965, 7, 15–19.
5.
BroganA.AlmrothB.O.Buckling of cylinders with cutoutsAm. Inst. Aeronaut. Astronaut. J., 1970, 8 (2), 236–241.
6.
RobinsonM.A comparison of yield surfaces for thin shellsInt. J. Mech. Sci, 1971, 13, 345–354.
7.
RobinsonM.GillS.S.Lower bound to the limit pressure of flush oblique cylindrical branch in a spherical pressure vesselInt. J. Mech. Sci., 1972, 14, 579–601.
8.
MarriotL. D.Evaluation of deformation or load control of stresses under inelastic conditions using elastic finite element stress analysis. In Proceedings of the Pressure Vessels and Piping Conference, Pittsburgh, Pennsylvania, 1988, PVP-Vol. 136 (American Society of Mechanical Engineers, New York).
9.
MackenzieD.BoyleJ.T.A method of estimating limit loads by iterative elastic analysis. I: Simple examplesInt. J. Pressure Vessels Piping, 1993, 53, 77–95.
10.
MackenzieD.NadarajahC.ShiJ.BoyleJ. T.Simple bounds on limit loads by elastic finite element analysisTrans. ASME, J. Pressure Vessels Technol., 1993, 115, 27–31.
11.
HardyS. J.Upper and lower bound limit and shakedown loads for hollow tubes with axisymmetric internal projections under axial loadingJ. Strain Analysis, 2001, 36 (6), 595–604.
12.
SeshadriR.MangalaramananS.P.Lower bound limit loads using variational concepts: The ma methodInt. J. Pressure Vessels Piping, 1997, 71, 93–106.
13.
ChouS. I.Stress state around a circular cylindrical shell with an elliptical hole under tensionTrans. ASME, June 1971, 534–456.
14.
FooS. S. B.On the limit analysis of cylindrical shells with a single cutoutInt. J. Pressure Vessels Piping, 1992, 49, 1–16.
15.
ShuH.The plastic limit load of circumferentially cracked thin-walled pipes under axial force, internal pressure and asymmetrical bendingInt. J. Pressure Vessels Piping, 2002, 79, 377–382.
16.
HeitzerM.Plastic limit loads of defective pipes under combined internal pressure and axial tensionInt. J. Mech. Sci., 2002, 44, 1219–1224.
17.
GuarracinoF.On the analysis of cylindrical tubes under flexure: Theoretical formulations, experimental data and finite element analysisThin Walled Structures, 2003, 41, 127–147.
18.
RahimiG. H.PoursaeidiE.Plastic analysis of cylindrical shells with single cutout under bending moment. In The Third International Conference onAdvanced Structural Engineering and Mechanics, Seoul, Korea, 2004, 908–922.
19.
RahimiG. H.AlashtiR. A.PoursaeidiE.Limit analyses of cylinders with circular opening under pure bending moment. In Proceedings of the 8th SSTA Conference, Jurata, Poland, October 2005, pp. 599–603.
