This paper reviews work related to the high-temperature creep analysis of pressurized circumferential pipe weldments. It is important to define the problem and thus metallurgical features correctly; the identification of material microstructural-property variations within the heat-affected zone (HAZ) and the failure modes of welds are briefly included, as well as in-service experience of pipe welds. Experimental methods, including model and full-size component testing, are summarized and examples of typical tests results are described. Material constitutive equations, which can be used in describing the creep deformation of and failure mechanisms in welds, are briefly described. Numerical modelling using finite element (FE) methods, covering a range of approaches and analyses, taking account of the effects of material properties, pipe geometry, weld dimensions and system loading, on the stresses and failure behaviour of pipe weldments, are summarized. Typical results are presented to illustrate the potential uses and limitations of the FE methods.
AlberryP. J.JonesW. K. C.A computer model for the prediction of HAZ microstructures in multipass weldsMetals Technol., 1982, 9 (10), 419–430.
2.
ReedR. C.BhadesiaH. K.D.H.A simple model for multipass weldsActa Metall. Mater., 1994, 42 (11), 3663–3678.
3.
RosenthalD.Mathematical theory of heat distribution during welding and cuttingWeld. J., Res. Suppl., 1941, 220, 220s-234s.
4.
FidlerR.Residual stresses in a CrMoV-2CrMo pipe weld. Part 1: The as welded conditionInt. J. Pressure Vessels Piping, 1983, 14, 35–62.
5.
FidlerR.Residual stresses in a CrMoV-2CrMo pipe weld. Part 2: The heat treated conditionInt. J. Pressure Vessels Piping, 1983, 14, 181–195.
6.
DongP.BrustF. W.Welding quality and effects on fracture in pressure vessel and piping componentsJ. Pressure Vessels Technol., August 2000, 122, 329–338.
7.
BrowneR. E. J.CaneB.ParkerJ. D.WaltersD.Creep failure analysis of butt welded tubes. In Proceedings of the Conference onCreep and Fracture of Engineering Materials and Structures, Swansea, 1981, pp. 645–659 (Pineridge Press, Swansea).
8.
ColemanM. C.ParkerJ. D.WaltersD.The behaviour of ferritic weldments in thick section CrMoV pipe at elevated temperaturesInt. J. Pressure Vessels Piping, 1985, 18, 277–310.
9.
CoussementC.De WitteM.De BackerT.VereslstL.Internal pressure creep testing on welded components of modified 9% Cr and 12% Cr steels. In Proceedings of the Conference onMaterials and Welding Technology in Power Plants, Essen, Germany, March 1994, Lecture 16 (Ver-einigung der Grosskraftwerksbetreiber).
10.
CraineR. E.NewmanM. G.Modelling creep failure in welded plates under uniaxial loadingJ. Strain Analysis, 1996, 31 (2), 117–124.
11.
HayhurstD. R.Computational continuum damage mechanics: Its use in the prediction of creep in structures—past, present and future. In Proceedings of the IUTAM Symposium onCreep in Structures (Eds MurakamiS.OhnoN.), Japan, 2000, pp. 175–188 (Kluwer, Dordrecht).
12.
HydeT. H.SunW.BeckerA. A.Assessment of the use of finite element creep steady state stresses for predicting the creep life of welded pipes. In Proceedings of the 4th International Conference onComputational Structures Technology (Ed. ToppingB. H. V.), Edinburgh, 1998, pp. 247–251 (Civil-Comp Press, London).
13.
HallF. R.HayhurstD. R.Continuum damage mechanics modelling of high-temperature deformation and failure in a pipe weldmentProc. R. Soc. Land. A, 1991, 443, 383–403.
14.
HayhurstD. R.PerrinI. J.CDM analysis of creep rupture in weldmentsProc. Engng Mechanics, 1995, 1, 393–396.
15.
HydeT. H.SunW.Creep of welded pipesProc. Instn Mech. Engrs, Part E: J. Process Mechanical Engineering, 1998, 212 (E3), 171–182.
16.
PerrinI. J.HayhurstD. R.Creep constitutive equations for 0.5Cr0.5Mo0.25V ferritic steel in the temperature range 600–675 °CJ. Strain Analysis, 1996, 31 (4), 299–314.
17.
PerrinI. J.HayhurstD. R.AinsworthR. A.Approximate creep rupture lifetimes for butt welded ferritic steel pressurized pipesEur. J. Mech. A/Solids, 2000, 19, 223–258.
18.
EasterlingK.Introduction to the Physical Metallurgy of Welding 1992 (Butterworth-Heinemann, London).
19.
GrongO.Metallurgical Modelling of Welding, 2nd edition, 1997 (Institute of Materials, London).
20.
ChristensenN.de L. DaviesV.GjermundsenK.Distribution of temperatures in arc weldingBr. Weld. J., 1965, 12, 54–63.
21.
Proceedings of a Workshop on Challenges and Solutions in Repair Welding for Power and Process Plant, San Diego, California, 1996, Welding Research Council Bulletin 412 (Pressure Vessel Research Council-Welding Research Council, New York).
22.
DongP.Residual stresses in repair welds and local PWHT effects. In Proceedings of the Conference onRepair Welding and Serviceability, San Diego, California, January 2001, pp. 145–169 (Welding Research Council, New York).
23.
CerjakH. (Ed.) Proceedings of Conferences on the Mathematical Modelling of Weld Phenomena, 1993 (2nd), 1995 (3rd), 1997 (4th) (Institute of Materials, London).
24.
JonesW. K.C.AlberryP. J.A model for stress accumulation in steels during welding. In Proceedings of the Conference onResidual Stresses in Welded Construction and Their Effects, London, 1977, pp. 15–26 (Welding Institute, Abingdon).
25.
MasubuchiK.BlodgettO. W.MatsuiS.RuudC. O.TsaiC. L.Residual stress and distortion In Welding Handbook, Vol. 1, Welding Science and Technology, 9th edition, 2001, Ch. 7 (American Welding Society, Miami, Florida).
26.
BS 2633: 1987Specification for Class 1 Arc Welding of Ferritic Pipework for Carrying Fluids, 1987 (British Standards Institution, London).
27.
HepworthJ. K.Residual stresses in submerged arc bead on plate welds. CEGB Report R/M/N1090, Central Electricity Generating Board, UK, 1981.
28.
HepworthJ. K.The effect of residual stress on the creep deformation of welded pipe. CEGB Report RD/M/1202R81, Central Electricity Generating Board, UK, 1981.
29.
WolstenholmeA. A.Transverse cracking and creep ductility of 2CrMo weld metals. In Proceedings of the Conference onTrends in Steels and Consumables for Welding, London, 1978 (Welding Institute, Abingdon).
30.
HydeT. H.SunW.BeckerA. A.Analysis of the impression creep test method using a rectangular indentor for determining the creep properties in weldsInt. J. Mech. Sci., 1996, 38, 1089–1102.
31.
ParkerJ. D.JamesJ. D.Creep behaviour of miniature disc specimens of low-alloy steel In Developments in a Progressing Technology, PVP-Vol. 279, 1994, pp. 167–172 (American Society of Mechanical Engineers, New York).
32.
CaneB. J.Collaborative programme on the correlation of test data for high-temperature design of welded steam pipes. Presentation and analysis of materials data. CEGB Report RD/L2101N81, Central Electricity Generating Board, UK, 1981.
33.
SpigareilliS.CerriE.EvangelistaE.BontempiP.Microstructure and creep of a T91 steel. In Proceedings of the Conference onAdvanced Heat Resistant Steels for Power Generation, San Sebastian, Spain, 1998, pp. 247–258 (Institute of Materials, London).
34.
EggelerG.RamtekeA.ColemanM. C.ChewB.PeterG.BurbliesA.HaldJ.JeffereyC.RantalaJ.De WitteM.MohrmannR.Analysis of creep in a welded ‘P91’ pressure vesselInt. J. Pressure Vessels Piping, 1994, 60, 237–257.
35.
BrettS. J.Cracking experience in steam pipework welds in National Power. In Proceedings of the Conference onMaterials and Welding Technology in Power Plants, 1994, Essen, Germany, March 1994, Lecture 8 (Vereinigung der Grosskraftwerksbetreiber)
36.
ToftL. H.YeldhamD. E.Weld performance of high pressure steam generating plant in the Midlands Region, CEGB. In Proceedings of the Conference on Welding Research Related to Power Plant, Southampton, 1972, pp. 5–19 (Central Electricity Generating Board, London).
37.
WilsonJ. D.HawkesM.JamesP.PascoeS.Degradation in ageing power plant components. In Proceedings of the Conference onParsons2000, Advanced Materials for 21st Century Turbines and Power Plant, Cambridge, July 2000, pp. 508–522.
38.
StoutR. D.Weldability of Steels, 4th edition, 1987 (Welding Research Council, New York).
39.
PriceA. T.Rupture ductility of creep resistant steels; fabrication and welding. In Proceedings of the Conference onRupture Ductility of Creep Resistant Steels, York, 1990, pp. 246–267 (Institute of Metals, London).
40.
EtienneC. F.HeeringsJ. H.Evaluation of the influence of welding on creep resistance. International Institute of Welding Document IX-1725–93, 1993; also inSteel Res., 1994, 65 (5), 187–196.
41.
CoussementC.De WitteM.DhoogeA.DobbelaereR.SteenM.Van Der DoncktE.Van MuysenL.Weldability and high-temperature behaviour of x20CrMoV 12 1 and 10CrMo9.10 base material, similar and dissimilar weldmentsLastudschrift-2, Rev. Soudure, 1990, 2, 27–36.
42.
HydeT. H.TangA.Creep analysis and life assessment using cross weld creep specimensInt. Mater. Rev., 1998, 43 (6), 221–242.
43.
SteenM.De WitteM.CoussementC.Creep properties of 12%Cr weldments. Part 2: Component tests and design implications. In Proceedings of the Conference on Creep and Fracture of Engineering Materials and Structures, Swansea, 1990, pp. 663–678 (Institute of Materials, London).
44.
WilliamsJ. A.The validation of procedures for assessing the life of components. In Proceedings of the Conference on BALTIC A 2, Life and Performance of High Temperature Materials and Structures, Helsinki, Finland, 1992, Session 2c, paper 2 (Technical Research Centre of Finland, Espoo).
45.
WaltersD. J.CockcroftR. D. M.A stress analysis and failure criteria for high temperature butt welds. In Proceedings of the Colloquium on Creep Behaviour of Welds in Boilers, Pressure Vessels Piping, 1972 (International Institute of Welding, Toronto).
46.
WaltersD. J.The stress analysis of cylindrical butt welds under creep conditions. CEGB Note RD/B/N3716, Central Electricity Generating Board, UK, 1976.
47.
BrettS. J.AllenD. J.PaceyJ.Failure of a modified 9Cr header end plate. In Proceedings of the Conference on Case Histories and Integrity of Failures in Industry, Milan, Italy, 1999, pp. 133–143.
48.
ColemanM. C.WaltersD.Comparison of measured and calculated creep strains in internally pressurized butt welds. CEGB Report RD/M/1833/R89, Central Electricity Generating Board, UK, 1989.
49.
BuddenP. J.Analysis of the type IV creep failure of three welded ferritic pressure vessels. Int. J. Pressure Vessels Piping, 1998, 75, 509–519.
50.
RobinsonD. N.SwindemanR. W.Unified creep plasticity constitutive equations for 2.25CrlMo steel at elevated temperatures. ORNL Report TM8444, Oak Ridge National Laboratory, Oak Ridge, Tennessee, 1982.
51.
EvansR. W.WilshireB.Creep of Metals and Alloys, 1985 (Institute of Metals, London).
52.
KachanovL. M.Izv. Akad. Nauk SSSR, 1958, 8, 26–31.
53.
HayhurstD. R.Creep rupture under multi-axial states of stress. J. Mech. Phys. Solids, 1972, 20, 381–390.
54.
HayhurstD. R.DimmerP. R.MorrisonC. J.Development of continuum damage in the creep rupture of notched bars. Phil. Trans. R. Soc. Lond. A, 1984, 311, 103–129.
55.
StoresundJ.AnderssonP.SamuelsonL. A.SegleP.Prediction of creep cracks in low alloy steel pipe welds by use of the continuum damage mechanics approach. In Proceedings of the 4th International Colloquium on Ageing of Materials and Methods for the Assessment of Lifetimes of Engineering Plant (Ed. PennyR. K.), Cape Town, South Africa, 1997, pp. 129–144.
56.
WangZ. P.HayhurstD. R.Material data for high-temperature design of ferritic steel pressure vessel weldments. Int. J. Pressure Vessels Piping, 1993, 55, 461–179.
57.
HydeT. H.SunW.BeckerA. A.A damage mechanics approach to predicting initiation and growth of type IV cracks in CrMoV weldments. In Proceedings of the 2nd International HIDA (High Temperature Defect Assessment) Conference on Advances in Defect Assessment in High Temperature Plant, Stuttgart, Germany, 2000 (Staatliche Materialprufungsanstalt, Stuttgart); also in Int. J. Pressure Vessels Piping, 2001, 78, 765–771.
58.
HydeT. H.SunW.WilliamsJ. A.Creep behaviour of parent, weld and HAZ materials of new, service-aged and repaired ½Cr½Mo¼V:2¼CrlMo pipe welds at 640 °CMater. High Temps, 1999, 16, 117–129.
59.
OthmanA. M.HayhurstD. R.Multi-axial creep rupture of a model structure using a two parameter model. Int. J. Mech. Sci., 1990, 32, 35–48.
60.
HydeT. H.SunW.BeckerA. A.WilliamsJ. A.Creep continuum damage constitutive equations for the base, weld and heat-affected zone materials of a service-aged ½Cr½Mo¼V:2¼CrlMo multi-pass weld at 640 °CJ. Strain Analysis, 1997, 32(4), 273–285.
61.
HydeT. H.SunW.Creep of waisted and notched cross-weld specimens. In Proceedings of the 7th International Conference on Creep and Fracture of Engineering Materials and Structures, Irving, California, 1997, pp. 759–768.
62.
TuS.-T.SandstromR.Numerical simulation of creep exhaustion of weldments and some design considerations. In Proceedings of the 5th International Conference on Creep and Fracture of Engineering Materials and Structures (Eds WilshireB.EvansR. W.), Swansea, 1993, pp. 695–704.
63.
HydeT. H.SunW.BeckerA. A.Effects of end loading on the creep failure behaviour of CrMoV welds in main steam pipelines. In Proceedings of the 6th International Conference on Damage and Fracture Mechanics: Computer Aided Assessment and Control (Eds SelvaduraiA. P. S.BrebbiaC. A.), Montreal, Canada, 2000, pp. 415–424 (Wessex Institute of Technology Press, Southampton and Boston).
64.
BuddenP. J.Analysis of modified 9%Cr weldment creep behaviour using a four material model. Nuclear Electric Report TD/SE/REP/0061/92, 1992.
65.
SunW.HydeT. H.BeckerA. A.WilliamsJ. A.A study of weld repairs in a CrMoV service-exposed pipe weld. In Proceedings of the 9th International Conference on Creep and Fracture of Engineering Materials and Structures, Swansea, April 2001, pp. 613–622.
66.
LawM.PaytenW.Weld performance under creep using finite element modelling. Int. J. Pressure Vessels Piping, 1997, 72, 45–49.
67.
StoresundJ.AnderssonP.SamuelsonL. A.SegleP.Prediction of creep cracks in low alloy steel pipe welds by use of the continuum damage mechanics approach. In Proceedings of the International Conference on Ageing of Materials and Methods for the Assessment of Lifetimes of Engineering Plant (Ed. PennyR.), 1997, pp. 129–144 (Balkema, Rotterdam).
68.
NorrishJ.Advanced Welding Processes, 1992 (Institute of Physics, Bristol).
69.
FidlerR.The effect of weld width on the performance of main steam pipes welded by the narrow gap process. CEGB Report TPRD/M/1583/R86, Central Electricity Generating Board, UK, 1986.
70.
FidlerR.The performance of narrow gap welds in creep conditions. CEGB Report RD/M/1696/RR88, Central Electricity Generating Board, UK, 1988.
71.
VazdaD.On concentration effects in circumferential welds due to dissimilar creep properties. Int. J. Pressure Vessels Piping, 1997, 73, 119–126.
72.
HydeT. H.WilliamsJ. A.SunW.Assessment of creep behaviour of narrow gap welds. Int. J. Pressure Vessels Piping, 1999, 76, 515–525.
73.
HydeT. H.SunW.BeckerA. A.WilliamsJ. A.Effect of weld angle and axial load on the creep failure behaviour of an internally pressurised thick walled CrMoV pipe weld. Int. J. Pressure Vessels Piping, 2001, 78, 365–372.
74.
VilhelmsenT.Modelling of creep behaviour in welded joints. In Proceedings of the 9th International Conference on Creep and Fracture of Engineering Materials and Structures, Swansea, April 2001, pp. 353–363 (Institute of Materials, London).
75.
HydeT. H.SunW.Effect of bending load on the failure behaviour of pressurised thick-walled CrMoV pipe weldment. Int. J. Pressure Vessels Piping, 2002, 79, 331–339.
76.
HydeT. H.SunW.TangA.BuddenP. J.An inductive procedure for determining the stresses in multimaterial components under steady state creep. J. Strain Analysis, 2000, 35(5), 347–358.
77.
HydeT. H.SunW.TangA.A general formulation of the steady state creep deformation of multi-material components. In Proceedings of the 4th International Conference on Modern Practice in Stress and Vibration Analysis (Ed. BeckerA. A.), Nottingham, 2000, pp. 481–492 (Engineering Materials Advisory Services, Warley).
78.
HydeT. H.SunW.TangA.A parametric analysis of stresses in a thick-walled pipe weld during steady-state creep. In Proceedings of the 5th International Colloquium on Ageing of Materials and Methods for the Assessment of Lifetimes of Engineering Plant (Ed. PennyR. K.), Cape Town, South Africa, 1999, pp. 231–246.
79.
WangZ. P.HayhurstD. R.The use of supercomputer modelling of high temperature failure in pipe welds to optimise weld and HAZ property selection. Proc. R. Soc. Lond. A, 1994, 446, 127–148.
80.
ASME Code N47-29 Class 1 Components in Elevated Temperature Service, 1992 (American Society of Mechanical Engineers, New York).
81.
EvansR. W.WilshireB.Extrapolation and creep life prediction for high temperature service. In Proceedings of the Seminar on Design of High Temperature Metallic Components, Petten, The Netherlands, June 1983, paper 4, 43 pp. (Commission of the European Communities, Joint Research Centre, Petten).
82.
LawM.PaytenW.SnowdenK.Finite element analysis of creep using theta projection data. Int. J. Pressure Vessels Piping, 1998, 75, 437–442.
83.
EvansR. W.A constitutive model for the high temperature creep of particle hardened alloys based on the theta projection method. Proc. R. Soc. Lond. A, 2000, 456, 835–868.
84.
LeckieF. A.HayhurstD. R.Creep rupture of structures, Proc. R. Soc. Lond. A, 1974, 340, 323–347.
AinsworthR. A.HalesR.BuddenP. (Eds) R5 (Issue 2): Assessment Procedure for the High Temperature Response of Structures, January 2001 (British Energy Limited, Bristol).
