Mutagenic effects of cutting fluids and components in the Salmonella typhimurium mutagenicity assay

Abstract

Emulsions of water-soluble cutting fluids (wsCF) are used in large quantities in the metal industry. In order to reduce the costs for use and disposal of these fluids, new technologies are being introduced. Minimist Lubricant Supply (MLS) uses only minimal amounts of cutting fluids. In contrast to conventional wsCF, which are complex multicompound mixtures, MLS cutting fluids are composed of one or two components only, like fatty alcohols and fatty acid esters. The aim of the study was to identify and compare the mutagenic potential of these cutting fluids as a first indicator of a possible hazard of systemic effects after inhalation or dermal absorption of the fluids at the workplace.

The Salmonella typhimurium assay (Ames assay) was used as a screening method to detect mutagenic effects of cutting fluids. Conventional wsCF and MLS cutting fluids were tested in the strains TA 98, TA 100, TA 102 and TA 104, in the presence and absence of an external metabolizing enzyme system (rat liver S9-mix), using a preincubation (20 min) test protocol.

For MLS fluids, no mutagenicity was found in a concentration range between 1 and 10 mg/plate in the Ames assay. Among five tested conventional wsCF, two were mutagenic in the Ames assay at concentration ranges between 2.5 and 15 mg/plate. In cooperation with the manufacturer, 18 defined components of cutting fluids were tested separately. The results revealed that formaldehyde generators, derivatives of oxazolidine and hexahydrotriazine used as biocides for preservation of the fluids, were mutagenic. Four components were nonmutagenic but cytotoxic, whereas the remaining components displayed no bacterial mutagenicity.

The present results show the potential hazard of biocides for workers handling these fluids. An exposure via inhalation and/or dermal absorption could cause an additional risk due to mutagenic ingredients. Under aspects of workers’ safety, a further discussion about the use of specific components in cutting fluids is recommended.

Keywords

Ames assay biocides water-soluble cutting fluids

Get full access to this article

View all access options for this article.

References

Alomar, A. 1994: Occupational skin disease from cutting fluids. Dermatologic Clinics 12, 537-546.

Apostoli, P. , Crippa, M. , Fracasso, M. E. , Cottica, D. and Alessio, L. 1993: Increases in polycyclic aromatic hydrocarbon content and mutagenicity in a cutting fluid as a consequence of its use. International Archives of Occupational and Environmental Health 64, 473-477.

Baumann, W. and Herberg-Liedtke, B. 1996: Chemikalien in der Metallbearbeitung. Berlin: Springer-Verlag.

Berufsgenossenschaftliches Institut für Arbeitssicherheit. Kühlschmierstoffe BIA-Report 7/96. In Schriftenreihe des Hauptverbandes der gewerblichen Berufsgenossenschaften. St. Augustin, Germany: Berufsgenossenschaftliches Institut fü r Arbeitssicherheit (BIA).

Dalbey, W. , Osimitz, T. , Kommineni, C. , Roy, T. , Feuston, M. and Yang, J. 1991: Four-week inhalation exposures of rats to aerosols of three lubricant base oils. Journal of Applied Toxicology 11, 297-302.

Deutsche Forschungsgemeinschaft(DFG). 2001: Kü hlschmierstoffe. In Greim, H., editor, Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begrü ndung von MAK-Werten, 32. Lieferung. Weinheim, Germany: VCH-Wiley.

Deutsche Forschungsgemeinschaft (DFG). 2000: Formaldehyd. In: Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begrü ndung von MAK-Werten. Weinheim, Germany: Wiley-VCH.

Deutsche Forschungsgemeinschaft(DFG). 1999: 2-Octyldode-can-1-ol. In Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begrü ndung von MAK-Werten. Weinheim, Germany: Wiley-VCH.

Deutsche Forschungsgemeinschaft (DFG). 1994: Natriumpyrithion. In Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begründung von MAK-Werten. Weinheim, Germany: Wiley-VCH.

10.

Deutsche Forschungsgemeinschaft (DFG). 1992: 5-Ethyl-3,7-dioxa-1-azabicyclo[3.3.0]octan. In Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begründung von MAK-Werten. Weinheim, Germany: Wiley-VCH.

11.

Deutsche Forschungsgemeinschaft (DFG). 1988: N, N?, N??-Tris(b-hydroxy-ethyl)-hexahydro-1,3,5-triazin. In Gesundheitsschä dliche Arbeitsstoffe, Toxikologisch-Arbeitsmedizinische Begründung von MAK-Werten. Weinheim, Germany: Wiley-VCH.

12.

Fuchs, J. , Hengstler, J. G. , Bolm-Andorff, U. , Oesch, F. 1995: DNA damage in mononuclear blood cells of metal workers exposed to N-nitrosodiethanolamine in synthetic fluids. Mutation Research 342, 95-102.

13.

Granella, M. , Clonfero, E. 1991: The mutagenic activity and polycyclic aromatic hydrocarbon content of mineral oils. International Archives of Occupational and Environmental Health 63, 149-153.

14.

Kennedy, S. M. , Greaves, I. A. , Kriebel, D. , Eisen, E. A. , Smith, T. J. and Woskie, S. R. 1989: Acute pulmonary responses among automobile workers exposed to aerosols of machining fluids. American Journal of Industrial Medicine 15, 627-641.

15.

Kleber, M., Blaszkewicz, M., Lucas, S., Föllmann, W. 2000: Toxikologische Aspekte bei der Verwendung von wassermischbaren Kühlschmierstoffen und Minimalmengenschmierstoffen. VDI-Berichte 1532, 155-74.

16.

Lautenschläger, H., Nissen, H.P. and Wieland, W. 1997: Neue Untersuchungen zur Hautverträglichkeit von Kühlschmierstoffen. Arbeitsmedizin in Sozialmedizin Prä ventivmedizin 32, 474-79.

17.

Maron, D. M. , Ames, B. N. 1983: Revised methods for the Salmonella mutagenicity test. Mutation Research 113, 173-215.

18.

Pfeiffer, T. 1993: Wettbewerbsfaktor Produktionstechnik. Dü s-Ku seldorf: VDI-Verlag.

19.

Rosenman, K. D. , Reilly, M. J. and Kalinowski, D. 1997: Work-related asthma and respiratory symptoms among workers exposed to metal-working fluids. American Journal Industrial Medicine 32, 325-331.

20.

Schaper, M. and Detwiler, K. 1991: Evaluation of the acute respiratory effects of aerosolized machining fluids in mice. Fundamental and Applied Toxicology 16, 309-319.

21.

Schmidt, J., Hühsam, A. and Dyck, M. 2000: Technologienetz Trockenbearbeitung - Wege zur angewandten Trockenbearbeitung in der Produktion. VDI-Berichte 1532, 229-36.

22.

Schroeder, J. C. , Tolbert, P. E. , Eisen, E. A. , Monson, R. R. , Hallock, M. F. , Smith, T. J. , Woskie, S. R. , Hammond, S. K. and Milton, D. K. 1997: Mortality studies of machining fluid exposure in the automobile industry IV: a case-control study of lung cancer. American Journal of Industrial Medicine 31, 525-533.

23.

Spallek, M. 1989: Astma bronchiale durch Kühlschmierstoff-Aerosole. Arbeitsmedizin in Sozialmedizin Prä ventivmedizin 24, 59-61.

24.

Stalder, K., Ladany, E., Kroll, A. and Pantke, T. Tierexperimentelle Untersuchungen zur Gesundheitsbeeinträchtigung durch Ölnebel. In Forschungsbericht 625.1. Dortmund, Germany: Bundesanstalt fü r Arbeitsschutz.

25.

Stork, J., Spallek, M., Labrot, B., Mann, H., Nörimg, R. and Saake, K.P. 1990: Akuter Einfluß einer Exposition gegenü ber Aerosolen eines wassergemischten Kühlschmierstoffes auf Meßwerte der Lungenfunktion. Arbeitsmedizin in Sozialmedizin Prä ventivmedizin 25, 372-74.

26.

Stork, J., Heger, M., Nöring, R. and Thamm, H. 1995: Inhalative Belastung durch Kühlschmierstoffaerosole -arbeitsmedizinische Aspekte. Zentralblatt fü r Arbeitsmedizin und Arbeitsschutz 45, 228-36.

27.

Technische Regeln fü r Gefahrstoffe TRGS 900: Grenzwerte für die Luft am Arbeitsplatz. In Nöthlichs, M. Gefahrstoffe, Nr. 3390. Berlin: Erich Schmidt Verlag.

28.

Ueno, S. , Shiomi, Y. and Yokata, K. 2002: Metalworking fluid hand dermatitis. Industrial Health 40, 291-292.

29.

Weinert, K. , Adams, F. J. and Thamke, D. 1995: Was kostet die Kühlschmierung. Technika 7, 19-23.

30.

Zacharisen, M. C. , Kadambi, A. R. , Schlueter, D. P. , Kurup, V. P. , Shack, J. B. , Fox, J. L. , Anderson, H. A. and Fink, J. N. 1998: The spectrum of respiratory disease associated with exposure to metal working fluids. Journal of Occupational and Environmental Medicine 40, 640-647.