In this study, the surface of AZ91 magnesium alloy plasma sprayed with WC–12 wt-%Co powder was melted by pulsed Nd:YAG laser. Microstructure, chemical composition and phase analyses of the treated layers were studied by utilising a scanning electron microscope equipped with energy dispersive spectroscopy, X-ray diffraction technique and a microhardness testing machine. Laser treated layers showed much finer structure compared to that of the original base material with suitable distribution of WC particles. Microhardness of melted zone achieved at optimum condition was ∼3.5 times higher than that of the base material. In addition, the presence of WC particle and refined structure reduced the wear rate to less than half in the laser treated layer.
ZhengB. J., ChenX. M. and LianJ. S.: ‘Microstructure and wear property of laser cladding Al+SiC powders on AZ91D magnesium alloy’, Opt. Lasers Eng., 2010, 48, 526–532.
3.
LiuY. H., GuoZ. X., YangY., WangH. Y., HuJ. D., LiY. X., ChumakovA. N. and BosakN. A.: ‘Laser (a pulsed Nd:YAG) cladding of AZ91D magnesium alloy with Al and Al2O3 powders’, Appl. Surf. Sci., 2006, 253, 1722–1728.
4.
DongH.: ‘Surface engineering of light alloys: aluminium, magnesium and titanium alloys’, 444–460; 2010, Cambridge, Woodhead Publishing.
5.
PolmearI.: ‘Light alloys – from traditional alloys to nanocrystals’, 237–290; 2006, Oxford, Elsevier.
6.
ZhangD., GouY., LiuY. and GuoX.: ‘A composite anodizing coating containing superfine Al2O3 particles on AZ31 magnesium alloy’, Surf. Coat. Technol., 2013, 236, 52–57.
7.
Uma RaniR., Maria ShaliniV., ThotaH. K. and SharmaA. K.: ‘Composition of corrosion performance of various convention coatings on magnesium alloy using electrochemical techniques’, J. Coat. Technol. Res., 2013, 10, 707–715.
8.
WuC. and ZhangJ.: ‘Corrosion protection of Mg alloys by cathodic electrodeposition coating pretreated with silane’, J. Coat. Technol. Res, 2010, 7, 727–735.
9.
CorreaE., ZuletaA. A., SepúlvedaM., GuerraL., CastañoJ. G., EcheverríaF., LiuH., SkeldonP. and ThompsonG. E.: ‘Nickel–boron plating on magnesium and AZ91D alloy by a chromium-free electroless process’, Surf. Coat. Technol., 2012, 206, 3088–3093.
10.
SunK., ShiQ. Y., SunY. J. and ChenG. Q.: ‘Microstructure and mechanical property of nano-SiCp reinforced high strength Mg bulk composites produced by friction stir processing’, Mater. Sci. Eng. A, 2012, A547, 32–37.
11.
ArrabalR., PardoA., MerinoM. C., MohedanoM., CasajúsP. and MerinoS.: ‘Al/SiC thermal spray coatings for corrosion protection of Mg–Al alloys in humid and saline environments’, Surf. Coat. Technol., 2010, 204, 2767–2774.
12.
MajumdarJ. D. and MannaI.: ‘Laser processing of materials’, Sadhana Acad. P. Eng. S., 2003, 28, 495–562.
13.
GrayJ. E. and LuanB.: ‘Protective coatings on magnesium and its alloys – a critical review’, J. Alloys Compd, 2002, 336, 88–113.
14.
MajumdarJ. D. and MannaI.: ‘Mechanical properties of a laser-surface-alloyed magnesium-based alloy (AZ91) with nickel’, Scr. Mater., 2010, 62, 579–581.
15.
PaitalS. R., BhattacharyaA., MoncayoM., HoY. H., MahdakK., NagS., BanerjeeR. and DahotreN. B.: ‘Improved corrosion and wear resistance of Mg alloys via laser surface modification of Al on AZ31B’, Surf. Coat. Technol., 2012, 206, 2308–2315.
16.
HazraM., MondalA. K., KumarS., BlawertC. and DahotreN. B.: ‘Laser surface cladding of MRI 153M magnesium alloy with (Al+Al2O3)’, Surf. Coat. Technol., 2009, 203, 2292–2299.
17.
ZhangZ., LinP. and RenL.: ‘Wear resistance of AZ91D magnesium alloy processed by improved laser surface remelting’, Opt. Lasers Eng., 2014, 55, 237–242.
18.
KhalfaouiW., ValerioE., MasseJ. E. and AutricM.: ‘Excimer laser treatment of ZE41 magnesium alloy for corrosion resistance and microhardness improvement’, Opt. Lasers Eng., 2010, 48, 926–931.
19.
ChehrghaniA., TorkamanyM. J., HamediM. J. and SabbaghzadehJ.: ‘Numerical modeling and experimental investigation of TiC formation on titanium surface pre-coated by graphite under pulsed laser irradiation’, Appl. Surf. Sci., 2012, 258, 2068–2076.
20.
JoshiS. V., PadmavathiC., SundarS. and RaoK. P.: ‘Effect of pulsed Nd?:YAG laser melting treatment on microstructural and corrosion behaviour of AZ91C Mg alloy’, Mater. Sci. Technol., 2006, 22, 583–589.
21.
MondalA. K., KumarS., BlawertC. and DahotreN. B.: ‘Effect of laser surface treatment on corrosion and wear resistance of ACM720 Mg alloy’, Surf. Coat. Technol., 2008, 202, 3187–3198.
22.
HazraS., SabiruddinK. and BandyopadhyayP. P.: ‘Plasma and HVOF sprayed WC-Co coatings as hard chrome replacement solution’, Surf. Eng., 2012, 28, (1), 37–43.
23.
GhadamiF., Heydarzadeh SohiM. and GhadamiS.: ‘Effect of bond coat and post-heat treatment on the adhesion of air plasma sprayed WC–Co coatings’, Surf. Coat. Technol., 2015, 261, 289–294.
24.
ZhanQ., YuL., YeF., XueQ. and LiH.: ‘Quantitative evaluation of the decarburization and microstructure evaluation of WC–Co during plasma spraying’, Surf. Coat. Technol., 2012, 206, (19–20), 4068–4074.
25.
GhadamiF., Heydarzadeh SohiM. and GhadamiS.: ‘Effect of TIG surface melting on structure and wear properties of air plasma-sprayed WC–Co coatings’, Surf. Coat. Technol., 2015, 261, 108–113.
26.
AfzalM., Nusair KhanA., Ben MahmudT., KhanT. I. and AjmalM.: ‘Effect of laser melting on plasma sprayed WC–12 wt.%Co coatings’, Surf. Coat. Technol., 2015, 266, 22–30.
27.
SanchezE., BannierE., SalvadorM. D., BonacheV., GarciaJ. C., MorgielJ. and GrzonkaJ.: ‘Microstructure and wear behaviour of conventional and nanostructured plasma-sprayed WC–Co coatings’, J. Therm. Spray Technol., 2010, 19, (5), 964–974.
28.
YildizF.: ‘Tribological properties of WC–12Co coating on AZ91 magnesium alloy fabricated by high velocity oxy-fuel spray’, High Temp. Mater. Proc., 2014, 33, (1), 41–48.
29.
FarayibiP. K., MurrayJ. W., HuangL., BoudF., KinnellP. K. and ClareA. T.: ‘Erosion resistance of laser clad Ti–6Al–4V/WC composite for waterjet tooling’, J. Mater. Process. Technol., 2014, 214, 710–721.
30.
KimH. J., KweonY. G. and ChangR. W.: ‘Wear and erosion behavior of plasma-sprayed WC–Co coatings’, J. Therm. Spray Technol., 1994, 3, 169–178.
31.
JacobsL., HylandM. M. and De BonteM.: ‘Comparative study of WC–cermet coatings sprayed via the HVOF and the HVAF process’, J. Therm. Spray Technol., 1998, 7, 213–218.
32.
LiC. J., OhmoriA. and HaradaY.: ‘Effect of powder structure on the structure of thermally sprayed WC–Co coatings’, J. Mater. Sci., 1996, 31, 785–794.
33.
AslS. K., SohiM. H., HokamotoK. and UemuraM.: ‘Effect of heat treatment on wear behavior of HVOF thermally sprayed WC–Co coatings’, Wear, 2006, 260, 1203–1208.
34.
KruseO., JanssonB. and FriskK.: ‘Experimental study of invariant equilibria in the Co–W–C and Co–W–C–Me (Me, Ti, Ta, Nb) systems’, J. Phase Equilib., 2001, 22, 552–555.
ChoT. Y., YoonJ. H., KimK. S., SongK. O., JooY. K., FangW., ZhangS. H., YounS. J., ChunH. G. and HwangS. Y.: ‘A study on HVOF coatings of micron and nano WC–Co powders’, Surf. Coat. Technol., 2008, 202, 5556–5559.
37.
ParcoM., ZhaoL., ZwickJ., BobzinK. and LugscheiderE.: ‘Investigation of HVOF spraying on magnesium alloys’, Surf. Coat. Technol., 2006, 201, 3269–3274.
38.
DrezatJ. M. and MokademS.: ‘Marangoni convection and fragmentation in laser treatment’, Mater. Sci. Forum, 2006, 508, 257–262.
39.
GuanY. C., ZhouW., LiZ. L. and ZhengH. Y.: ‘Study on the solidification microstructure in AZ91D Mg alloy after laser surface melting’, Appl. Surf. Sci., 2009, 255, 8235–8238.
40.
ChenC., WangM., WangD., JinR. and LiuY.: ‘Laser cladding of Mg20Al80 powder on ZM5 magnesium alloy’, Corros. Eng. Sci. Thechnol., 2007, 42, 130–136.
41.
KouS.: ‘Welding metallurgy’, 2nd edn, 199–209; 2002, Hoboken, NJ, John Wiley & Sons, Inc.
42.
Y. C. Guan, W. Zhou, H.Y. Zheng, Z.L. Li, Solidification microstructure of AZ91D Mg alloy after laser surface melting. Appl. Phys. A: 101A, 2010, 339–344.
43.
ChongP. H., LiuZ., SkeldonP. and ThompsonG. E.: ‘Large area laser surface treatment of aluminium alloys for pitting corrosion protection’, Appl. Surf. Sci., 2003, 208–209, 399–404.
44.
TeleszkyI., BorosF., RooszA. and BuzaG.: ‘Solidification of A1–6Zn–2Mg alloy after laser remelting’, Mater. Sci. Eng. A, 1993, A173, 351–354.
45.
NathS., PityanaS. and MajumdarJ. D.: ‘Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance’, Surf. Coat. Technol., 2012, 206, 3333–3341.
46.
J. M.Guilemany, J.M. de Paco, J. Nutting, J.R. Miguel, Characterisation of W2C phase formed during the high velocity oxygen fuel spraying of a WC+12 pct Co powder. Metall. Mater. Trans. A: 30A, 1999, 1913–1921.
