In this study, functionally graded Ni–P coatings with a gradual change of phosphorus content were deposited using a single electroless bath. For comparing tribological and mechanical properties, three types of single layer coatings were deposited. According to the results among the single layer coatings, medium P coating had the minimum wear resistance, while its hardness was not minimum. The main reason may be that the medium P coating had the minimum H/E ratio, and this ratio is a more appropriate parameter than hardness for predicting wear resistance. Results of nanoindentation test showed gradual changes in hardness profile in the cross-section of FGCs due to the gradual changes of phosphorus content in the thickness of the coatings and, consequently, gradual changes in structures. In addition, functionally graded coatings indicated much better wear resistance than single layer coatings because during the wear process cracks were effectively prevented through the thickness as a result of gradual composition and structures.
ZarebidakiA. and AllahkaramS. R.: ‘Porosity measurement of electroless Ni–P coatings reinforced by CNT or SiC particles’, Surf. Eng., 2012, 28, 400–405.
4.
BanC. L., ShaoX. and WangL. P.: ‘Ultrasonic irradiation assisted electroless Ni–P coating on magnesium alloy’, Surf. Eng., 2014, 30, 880–885.
5.
SadhirM. H., SaranyaM., AravindM., SrinivasanA., SiddharthanA. and RajendranN.: ‘Comparison of in situ and ex situ reduced graphene oxide reinforced electroless nickel phosphorus nanocomposite coating’, Appl. Surf. Sci., 2014, 320, 171–176.
6.
AlirezaeiS., MonirvaghefiS. M., SaatchiA., ÜrgenM. and MotallebzadehA.: ‘High temperature tribology of nanocrystalline Ni–P–Ag coating’, Surf. Eng., 2013, 29, 306–311.
7.
WangL. L., ChenH. J. and ChenZ. L.: ‘Study on post-treatments for electroless Ni–P coating’, Surf. Eng., 2011, 27, 57–60.
8.
GoldsteinA. W., RostokerW. and RezekJ. J.: ‘Electron microscope study of the nucleation and growth of electroless cobalt and nickel’, Electrochem. Soc., 1972, 119, 1614–1619.
9.
JiangB., JiangS. L., MaA. L. and ZhengY. G.: ‘Erosion–corrosion behavior of electroless Ni–P coating on copper–nickel alloy in 3.5 wt.% sodium chloride solution’, J. Mater. Eng. Perform., 2014, 23, 230–237.
10.
ParkS. and LeeD.: ‘A study on the microstructure and phase transformation of electroless nickel deposits’, J. Mater. Sci., 1988, 23, 1643–1654.
11.
TaheriR.: ‘Evaluation of electroless nickel–phosphorus (EN) coatings’, 2002;. PhD thesis, University of Saskatchewan, Saskatoon, Canada..
12.
UpadhyayR. K. and KumaraswamidhasL. A.: ‘Surface modification by multilayered W/W2N coating’, Surf. Eng., 2014, 30, 475–482.
13.
GaoF., YangQ., LiuR. and HuangX.: ‘Oxidation resistance of novel multilayer coatings for gas turbine components’, Surf. Eng., 2014, 30, 624–635.
14.
BeliardouhN. E., BouzidK., NouveauC., TliliB. and WalockM. J.: ‘Tribological and electrochemical performances of Cr/CrN and Cr/CrN/CrAlN multilayer coatings deposited by RF magnetron sputtering’, Tribol. Int., 2015, 82, 443–452.
15.
Al-BukhaitiM. A., Al-hatabK. A., TillmannW., HoffmannF. and SpruteT.: ‘Tribological and mechanical properties of Ti/TiAlN/TiAlCN nanoscale multilayer PVD coatings deposited on AISI H11 hot work tool steel’, Appl. Surf. Sci., 2014, 318, 180–190.
16.
BaranÖ., BidevF., ÇiçekH., KaraL., Efeog˘luI˙. and Küçükömerog˘luT.: ‘Investigation of the friction and wear properties of Ti/TiB2/MoS2 graded-composite coatings deposited by CFUBMS under air and vacuum conditions’, Surf. Coat. Technol., 2014, 260, 310–315.
17.
FoppianoS., MarshallS. J., SaizE., TomsiaA. P. and MarshallG. W.: ‘Functionally graded bioactive coatings: Reproducibility and stability of the coating under cell culture conditions’, Acta Biomater., 2006, 2, 133–142.
18.
SongY. w., ShanD. y., ChenR. s. and HanE. h.: ‘A novel dual nickel coating on AZ91D magnesium alloy’, Trans. Nonferrous Met. Soc. China, 2008, 18, 339–343.
19.
Avelar-BatistaJ. C., SpainE., LetchM., HousdenJ. and BeecheyR.: ‘Improvements on the wear resistance of high thermal conductivity Cu alloys using an electroless Ni–P coating prior to PVD deposition’, Surf. Coat. Technol., 2006, 201, 4052–4057.
20.
GuC., LianJ., LiG., NiuL. and JiangZ.: ‘High corrosion-resistant Ni–P/Ni/Ni–P multilayer coatings on steel’, Surf. Coat. Technol., 2005, 197, 61–67.
21.
GripsV. K. W., Ezhil SelviV., BarshiliaH. C. and RajamK. S.: ‘Effect of electroless nickel interlayer on the electrochemical behavior of single layer CrN, TiN, TiAlN coatings and nanolayered TiAlN/CrN multilayer coatings prepared by reactive dc magnetron sputtering’, Electrochim. Acta, 2006, 51, 3461–3468.
22.
ZhangS., LiQ., YangX., ZhongX., DaiY. and LuoF.: ‘Corrosion resistance of AZ91D magnesium alloy with electroless plating pretreatment and Ni–TiO2 composite coating’, Mater. Charact., 2010, 61, 269–276.
23.
Sankara NarayananT. S. N., BaskaranI., KrishnaveniK. and ParthibanS.: ‘Deposition of electroless Ni–P graded coatings and evaluation of their corrosion resistance’, Surf. Coat. Technol., 2006, 200, 3438–3445.
24.
ZhangW. X., JiangZ. H., LiG. Y., JiangQ. and LianJ. S.: ‘Electroless Ni–P/Ni–B duplex coatings for improving the hardness and the corrosion resistance of AZ91D magnesium alloy’, Appl. Surf. Sci., 2008, 254, 4949–4955.
25.
NarayananT. S. N. S., KrishnaveniK. and SeshadriS. K.: ‘Electroless Ni–P/Ni–B duplex coatings: preparation and evaluation of microhardness, wear and corrosion resistance’, Mater. Chem. Phys., 2003, 82, 771–779.
26.
HaoL., WeiJ. and GanF. X.: ‘Electroless Ni–P coating on W–Cu composite via three different activation processes’, Surf. Eng., 2009, 25, 372–375.
27.
UngárT.: ‘Dislocation densities, arrangements and character from X-ray diffraction experiments’, Mater. Sci. Eng. A, 2001, A309–A310, 14–22.
28.
WilliamsonG. K. and HallW. H.: ‘X-ray line broadening from field aluminium and Wolfram’, Acta Metall., 1953, 1, 22–31.
29.
LambertM. R. and DuquetteD. J.: ‘A study of electroless nickel coatings containing low phosphorus’, Thin Solid Films, 1989, 177, 207–223.
30.
HurK. H., JeongJ. H. and LeeD. N.: ‘Microstructures and crystallization of electroless NiP deposits’, J. Mater. Sci., 1990, 25, 2573–2584.
31.
HouK. H., JengM. C. and GerM. D.: ‘A study on the wear resistance characteristics of pulse electroforming Ni–P alloy coatings as plated’, Wear, 2007, 262, 833–844.
32.
GawneD. T. and MaU.: ‘Engineering properties of chromium plating and electroless and electroplated nickel’, Surf. Eng., 1988, 4, 239–249.
33.
LeylandA. and MatthewsA.: ‘On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour’, Wear, 2000, 246, 1–11.
34.
MatthewsA. and LeylandA.: ‘Materials related aspects of nanostructured tribological coatings’, 40–45; Proc. 51st Ann. Technol. Conf. on ‘Society of vacuum coaters. Albuquerque, CO, USA, April2008.
35.
WangL., GaoY., XueQ., LiuH., XuT. and novelA.: ‘electrodeposited Ni–P gradient deposit for replacement of conventional hard chromium’, Surf. Coat. Technol., 2006, 200, 3719–3726.
