Modelling open hole compressive strength of composite laminates tested in hot wet conditions

Abstract

The objective of this paper is to analytically predict the compressive and in-plane shear response of T800/924C carbon fibre epoxy composite laminates (currently available for aerospace structural applications) exposed to hot wet environments. The weight gains, maximum moisture contents and diffusion coefficients of unidirectional and various multidirectional laminates immersed in boiling water (accelerated aging) were measured in earlier work and briefly reported here. Data are also presented on the effects of moisture and temperature on the uniaxial compressive strength/failure mode of unidirectional laminates and multidirectional plates with an open hole. It is observed that the failure in the hot wet specimens always occurs as a result of out-of-plane microbuckling of the 0° plies. This is attributed to the reduction in matrix strength properties and weakening of the ply interface arising from elevated temperatures and environmental conditioning. Test results are compared to theoretical predictions made by the Budiansky fibre microbuckling model and the Soutis–Fleck cohesive zone model for the open hole (notched) compressive (OHC) strength.

Keywords

COMPOSITE MATERIALS LAMINATES COMPRESSIVE STRENGTH SHEAR STRENGTH ENVIRONMENTAL DEGRADATION HYGRO-THERMAL EFFECTS OPEN HOLE COMPRESSION FIBRE MICROBUCKLING COHESIVE ZONE MODEL

Get full access to this article

View all access options for this article.

References

Potter

R. T.

and Purslow

: Composites , 1983, 14, (3), 206–225.

Barker

A. J.

and Balasundaram

: Composites , 1987, 18, (3), 217–226.

Soutis

and Turkmen

: Appl. Comp. Mater. , 1995, 6, (2), 327–342.

Soutis

and Turkmen

: Adv. Comp. Lett. , 1995, 4, (4), 115–120.

Soutis

and Turkmen

: J. Comp. Mater. , 1997, 31, (8), 832–849.

Browning

C. E.

, Husman

C. E.

and Whitney

J. M.

: ‘Moisture effects in epoxy matrix composites’, 1977, AFML-TR-77-41.

Copley

S. M.

: ‘A computer program to model moisture diffusion and its application to accelerated ageing of composites’, 1982, Royal Aircraft Establishment (RAE), TR-82010.

Curtis

P. A.

: ‘CRAG test methods for the measurement of the engineering properties of fibre-reinforced plastics’, 1985, RAE, TR-85099.

Soutis

and Fleck

N. A.

: J. Comp. Mater. , 1990, 24, 538–556.

10.

Soutis

, Flek

N. A.

and Smith

P. A.

: J. Comp. Mater. , 1991, 25, 1476–98.

11.

Soutis

, Curtis

P. T.

and Fleck

N. A.

: Proc. R. Soc. Lon. A , 1993, 440A, 241–256.

12.

de Wilde

W. P.

and Frolkovic

: Composites , 1994, 25, (2), 119–127.

13.

Shen

and Springer

G. S.

: J. Comp. Mater. , 1976, 10, 2–20.

14.

Naeem

: ‘The resistance of glass reinforced thermosetting polymers to thermohumid conditions’, PhD thesis, Loughborough University of Technology, UK, 1995.

15.

Budiansky

: Comput. Struct. , 1983, 16, (1), 3–12.

16.

Soutis

and Curtis

P. T.

: Composites A , 2000, 31A, (7), 733–740.

17.

Laminate Analysis Program (LAP), Composite Materials Design Tool, Version 4, 2002, Anaglyph Ltd.

18.

Soutis

: Proc. 13th European Conference of Composite Materials (ECCM13), Stockholm, Sweden, June 2008, SICOMP AB, Paper no ECCM-ID-0703.

19.

Lee

and Soutis

: Comp. Sci. Technol , 2007, 67, (10), 2015–2026.

20.

Soutis

and Lee

: Comp. Sci. Technot , 2008, 68, (12), 2359–2366.