The plastic deformation of a high entropy alloy Al0.5CoCrFeNi was investigated by instrumented nanoindentation over a broad range of strain rates at room temperature. Results show that the creep behaviour depends on the strain rate remarkably. In situ scanning images showed a significant pile up around the indents, demonstrating that a highly localised plastic deformation occurred in the process of nanoindentation. Under different strain rates, contact stiffness and elastic modulus basically remain unchanged. However, the hardness decreases as indentation depth increases due to indentation size effect. For the same maximum load, serrations became less prominent as the loading rate of indentation increased. Similar serrations have been observed in the current alloy upon quasi-static compression.
YehJ. W.: ‘Recent progress in high-entropy alloys’, Ann. Chim. Sci. Mater., 2006, 31, 633–648.
2.
YehJ. W., ChenS. K., LinS. J., GanJ. Y., ChinT. S., ShunT. T., TsauC. H. and ChangS. Y.: ‘Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes’, Adv. Eng. Mater., 2004, 6, 299–303.
3.
SenkovO. N., WilksG. B., MiracleD. B., ChuangC. P. and LiawP. K.: ‘Refractory high-entropy alloys’, Intermetallics, 2010, 18, 1758–1765.
4.
LiuW. H., WuY., HeJ. Y., NiehT. G. and LuZ. P.: ‘Grain growth and the Hall-Petch relationship in a high-entropy FeCrNiCoMn alloy’, Scr. Mater., 2013, 68, 526–529.
5.
ZhangW. Q., LouC. S., WuX. C., FuH. M. and ZhangH. F.: ‘Microstructures and mechanical property of AlCoNiCrFe alloy annealed in high magnetic field’, Mater. Sci. Technol.; http://dx.doi.org/10.1179/1743284714Y.00000006982014..
6.
QiaoJ. W., MaS. G., HuangE. W., ChuangC. P., LiawP. K. and ZhangY.: ‘Microstructural characteristics and mechanical behaviors of AlCoCrFeNi high-entropy alloys at ambient and cryogenic temperatures’, Mater. Sci. Forum, 2011, 688, 419–425.
7.
ZhangY., ZuoT. T., TangZ., GaoM. C., DahmenK. A., LiawP. K. and LuZ. P.: ‘Microstructures and properties of high-entropy alloys’, Prog. Mater. Sci., 2014, 61, 1–93.
8.
CantorB., ChangI. T. H., KnightP. and VincentA.: ‘Microstructural development in equiatomic multicomponent alloys’, Mater. Sci. Eng. A, 2004, A375–A377, 213–218.
9.
YehJ. W., LinS. J., ChinT. S., GanJ. Y., ChenS. K., ShunT. T., TsauC. H. and ChangS. Y.: ‘Formation of simple crystal structures in solid solution alloys with multiprincipal metallic elements’, Metall. Mater. Trans. A, 2004, 35A, 2533–2536.
10.
Fischer-CrippsA. C.: ‘Nanoindentation’; 2011, New York, Springer.
11.
OliverW. C. and PharrG. M.: ‘An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments’, J. Mater. Res., 1992, 7, 1564–1583.
12.
OliverW. C. and PharrG. M.: ‘Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology’, J. Mater. Res., 2004, 19, 3–20.
13.
DaoM., ChollacoopN., Van vlietK. J., VenkateshT. A. and SureshS.: ‘Computational modeling of the forward and reverse problems in instrumented sharp indentation’, Acta Mater., 2001, 49, 3899–3918.
14.
Fischer-CrippsA. C.: ‘A simple phenomenological approach to nanoindentation creep’, Mater. Sci. Eng. A, 2004, A385, 74–82.
15.
SureshS. and GiannakopoulosA. E.: ‘A new method for estimating residual stresses by instrumented sharp indentation’, Acta Mater., 1998, 46, 5755–5767.
16.
ZhuC., LuZ. P. and NiehT. G.: ‘Incipient plasticity and dislocation nucleation of FeCoCrNiMn high-entropy alloy’, Acta Mater., 2013, 61, 2993–3001.
17.
WangW. R., WangW. L. and YehJ. W.: ‘Phases, microstructure and mechanical properties of AlxCoCrFeNi high-entropy alloys at elevated temperatures’, J. Alloys Compd, 2014, 589, 143–152.
18.
WangW. J., GuoS., WangQ., LiuZ. Y., WangJ. C., YangY. and LiuC. T.: ‘Nanoindentation characterized initial creep behavior of a high-entropy-based alloy CoFeNi’, Intermetallics, 2014, 53, 183–186.
19.
SimmonsG. and WangH.: ‘Single crystal elastic constants and calculated aggregate properties’; 1971, Cambridge, MA, The M.I.T Press.
20.
WangW. R., WangW. L., WangS. C., TsaiY. C., LaiC. H. and YehJ. W.: ‘Effects of Al addition on the microstructure and mechanical property of AlxCoCrFeNi high-entropy alloys’, Intermetallics, 2012, 26, 44–51.
21.
XiaoG. S., YuanG. Z., JiaC. N., YangX. X., LiZ. G. and ShuX. F.: ‘Strain rate sensitivity of Sn-3.0Ag-0.5Cu solder investigated by nanoindentation’, Mater. Sci. Eng. A, 2014, A613, 336–339.
22.
ChudobaT. and RichterF.: ‘Investigation of creep behaviour under load during indentation experiments and its influence on hardness and modulus results’, Surf. Coat. Technol., 2001, 148, 191–198.
23.
MilmanY. V., GolubenkoA. A. and DubS. N.: ‘Indentation size effect in nanohardness’, Acta Mater., 2011, 59, 7480–7487.
24.
ManikaL. and ManiksJ.: ‘Size effects in micro- and nanoscale indentation’, Acta Mater., 2006, 54, 2049–2056.
25.
LucasB. N. and OliverW. C.: ‘Indentation power-law creep of high-purity indium’, Metall. Mater. Trans. A, 1999, 30A, 601–610.
26.
SchuhC. A. and NiehT. G.: ‘A nanoindentation study of serrated flow in bulk metallic glasses’, Acta Mater., 2003, 51, 87–99.
27.
KubinL. P., ChihabK. and EstrinY.: ‘The rate dependence of the portevin-Le chatelier effect’, Acta Metall., 1988, 36, 2707–2718.
28.
SenkovO. N. and JonasJ. J.: ‘Dynamic strain aging and hydrogen-induced softening in alpha titanium’, Metall. Mater. Trans. A, 1996, 27A, 1877–1887.
29.
AntonagliaJ., XieX., TangZ., TsaiC. W., QiaoJ. W., ZhangY., LaktionovaM. O., TabachnikovaE. D., CarrollR., YehJ. W., SenkovO. N., GaoM., UhlJ. T., LiawP. K. and DahmenK. A.: ‘Temperature effects on deformation and serration behavior of high-entropy alloys (HEAs)’, JOM, 2014, 66, 2002–2008.
