A two-stage thermodynamic calculation procedure was developed to analyse alloy compositions for rheocasting. Based on Kazakov's criteria, the processability of AZ91, AZ61 and AM60B for rheocasting was investigated. The results show that these alloys do not satisfy selected criteria fully, and only AZ91 is possible to be used for rheocasting with semisolid slurry having lower fraction solid (0.2–0.4). In microstructure produced by rheocasting, the β-Mg17Al12 phase forms continuous network along primary α-Mg gain boundary and is concentrated in this limited contiguous space. The routes to modify and optimise alloy composition were proposed.
NeiteG., KubotaK., HigashiK. and HehmannF.: ‘Magnesium based alloys’, in ‘Materials science and technology’ (ed. CahnR. W., ,., Vol. 8, 113–212; 1996, Weinheim, VCH.
2.
SachdevaD., TiwariS., SundarrajS. and LuoA.: ‘Microstructure and corrosion characterization of squeeze cast AM50 magnesium alloys’, Metall. Mater. Trans. B,, 2010, 41B, 1375–1383. doi: 10.1007/s11663-010-9433-x
3.
AguilarJ. and Buhrig-PolaczekA.: ‘Processing and properties of magnesium alloys in the semisolid state’, Int. Foundry Res., 2007, 59, 2–11.
4.
ZhaoZ., ChenQ., KangF. and ShuD.: ‘Microstructure evolution and tensile mechanical properties of thixoformed AZ91 magnesium alloy with the addition of yttrium’, J. Alloys Compd, 2009, 482, 455–467. doi: 10.1016/j.jallcom.2009.04.059
5.
JiangJ., WangY., QuJ., DuZ. and LuoS.: ‘Numerical simulation and experimental validation of thixoforming angle frame of AZ61 magnesium alloy’, Trans. Nonferr. Met. Soc. China, 2010, 20, s888–s892. doi: 10.1016/S1003-6326(10)60601-2
6.
CzerwinskiF.: ‘Magnesium injection molding’; 2008, New York, Springer Verlag.
7.
CzerwinskiF.: ‘Near-liquidus molding of Mg–Al and Mg–Al–Zn alloys’, Acta Mater., 2005, 53, 1973–1984. doi: 10.1016/j.actamat.2005.01.009
8.
CzerwinskiF., LipiecA. Z., PinetP. J. and OverbeekeJ.: ‘Correlating the microstructure and tensile properties of a thixomolded AZ91D magnesium alloy’, Acta Mater., 2001, 49, 1225–1235. doi: 10.1016/S1359-6454(01)00015-5
9.
TsukedaT., SaitoK. and KuboH.: ‘Tensile properties of injection molded Mg–Al based alloys’, J. Jpn Inst. Light Met., 1999, 49, 421–425. doi: 10.2464/jilm.49.421
10.
KleinerS., BeffortO., WahlenA. and UggowitzerP. J.: ‘Microstructure and mechanical properties of squeeze cast and semi-solid cast Mg–Al alloys’, J. Light Met., 2002, 2, 277–280. doi: 10.1016/S1471-5317(03)00012-9
11.
KorenZ., RosensonH., GutmanE. M., UnigovskiY. and EliezerA.: ‘Development of semisolid casting for AZ91 and AM50 magnesium alloys’, J. Light Met., 2002, 2, 81–87. doi: 10.1016/S1471-5317(02)00026-3
12.
FanZ., LiuG. and WangY.: ‘Microstructure and mechanical properties of rheo-diecast AZ91D magnesium alloy’, J. Mater. Sci., 2006, 41, 3631–3644. doi: 10.1007/s10853-006-6248-x
13.
JiS., QianM. and FanZ.: ‘Semisolid processing characteristics of AM series Mg alloys by rheo-diecasting’, Metall. Mater. Trans. A, 2006, 37A, 779–787. doi: 10.1007/s11661-006-0049-3
14.
ZhenZ., QianM., JiS. and FanZ.: ‘The effects of rheo-diecasting on the integrity and mechanical properties of Mg–6Al–1Zn’, Scr. Mater., 2006, 54, 207–211. doi: 10.1016/j.scriptamat.2005.09.032
15.
GuoH. M., ZhangA. S., HuB., DingY. and LiuX. B.: ‘Refining microstructure of AZ91 magnesium alloy by introducing limited angular oscillation during initial stage of solidification’, Mater. Sci. Eng. A, 2012, A532, 221–229. doi: 10.1016/j.msea.2011.10.083
16.
CurleU. A., WilkinsD. J. and GovenderG.: ‘R-HPDC of magnesium alloys’, Solid State Phenom., 2013, 192–193, 225–230. doi: 10.4028/www.scientific.net/SSP.192-193.225
17.
GuanR. G., ZhaoZ. Y., ZhangH., LianC., LeeC. S. and LiuC. M.: ‘Microstructure evolution and properties of Mg–3Sn–1Mn (wt) alloy strip processed by semisolid rheo-rolling’, J. Mater. Process. Technol., 2012, 212, 1430–1436. doi: 10.1016/j.jmatprotec.2012.02.001
18.
JorstadJ.: ‘SSM provides important advantages; so, why has SSM failed to achieve greater market share?’, Solid State Phenom., 2015, 217–218, 481–496. doi: 10.4028/www.scientific.net/SSP.217-218.481
19.
MidsonS. P.: ‘Industrial applications for aluminum semi-solid castings’, Solid State Phenom., 2015, 217–218, 487–495. doi: 10.4028/www.scientific.net/SSP.217-218.487
LiuD., AtkinsonH. V. and JonesH.: ‘Thermodynamic prediction of thixoformability in alloys based on the Al–Si–Cu and Al–Si–Cu–Mg systems’, Acta Mater., 2005, 53, 3807–3819. doi: 10.1016/j.actamat.2005.04.028
22.
LiuY. Q., DasA. and FanZ.: ‘Thermodynamic predictions of Mg–Al–M (M = Zn, Mn, Si) alloy compositions amenable to semisolid metal processing’, Mater. Sci. Technol., 2004, 20, 35–41. doi: 10.1179/026708304225011973
23.
KozlovA., DjurdjevicM. and Schmid-FetzerR.: ‘Thermodynamic simulation of phase formation during blending of Mg-alloys by thixomolding’, Adv. Eng. Mater., 2007, 9, 731–738. doi: 10.1002/adem.200700156
24.
PatelJ. B., LiuY. Q., ShaoG. and FanZ.: ‘Rheo-processing of an alloy specially designed for semi-solid metal processing based on the Al–Mg–Si system’, Mater. Sci. Eng. A, 2008, A476, 341–349. doi: 10.1016/j.msea.2007.05.046
25.
GuoH. M., ZhangS. G., YangX. J., LiuX. B. and JinH. L.: ‘Microstructure evolution and mechanical properties of rheo-squeeze cast Mg–9Al–1Zn alloy by experiments and thermodynamic calculation’, Metall. Mater. Trans. A, to be published.
26.
KaufmannH. and UggowitzerP. J.: ‘Fundamentals of the new rheocasting process of magnesium alloys’, Adv. Eng. Mater., 2001, 3, 963–967. doi: 10.1002/1527-2648(200112)3:12<963::AID-ADEM963>3.0.CO;2-X
27.
MartinezR. A. and FlemingsM. C.: ‘Evolution of particle morphology in semisolid processing’, Metall. Mater. Trans. A,, 2005, 36A, 2205–2210. doi: 10.1007/s11661-005-0339-1
28.
WannasinJ., MartinezR. A. and FlemingsM. C.: ‘Grain refinement of an aluminum alloy by introducing gas bubbles during solidification’, Scr. Mater., 2006, 55, 115–118. doi: 10.1016/j.scriptamat.2006.04.003
29.
GuoH. M., YangX. J. and LuoX. Q.: ‘Formation of grain refined and non-dendritic microstructure of an aluminum alloy under angular oscillation’, J. Alloys Compd, 2009, 482, 412–415. doi: 10.1016/j.jallcom.2009.04.035
ReisiM. and NiroumandB.: ‘Growth of primary particles during secondary cooling of a rheocast alloy’, J. Alloys Compd, 2009, 475, 643–647. doi: 10.1016/j.jallcom.2008.07.090
