Comparison of 3DSIM thermal modelling of selective laser melting using new dynamic meshing method to ANSYS

Abstract

Selective laser melting (SLM) is an additive manufacturing (AM) process in which parts are fabricated by selectively melting regions of the surface of a metallic powder bed in a layer-by-layer fashion. Various thermal phenomena such as heat conduction, convection, radiation, melting and solidification, dynamic phase changes, and evaporation occur during the SLM process. In addition, laser intensity and powder bed scan speeds during processing complicate understanding of the process due to complex dynamic interactions between the powder bed and laser. In order to study these dynamic interactions, a finite element model has been developed which uses a dynamic mesh with spatial non-linear thermal properties to track the point of laser exposure on the powder bed to study thermal evolution during SLM. The model is able to achieve a refined, localised mesh in the melt zone and heat affected zone (HAZ), surrounded by a relatively coarse mesh outside of the HAZ regions. The dynamic meshing for this implementation is achieved using both the sub-modelling functionality in ANSYS and a new set of algorithms being commercialised by 3DSIM, LLC. It was found that dynamic meshing reduces the model size and computational burden. In this paper, the use of the sub-modelling approach for dynamic meshing was verified by comparing it against a uniform fine mesh model. The results of the two models match within an acceptable tolerance. Also, a mesh sensitivity analysis was carried out in order to show solution convergence as a function of increasing mesh density. The results of this analysis were also validated using experiments to show a match between experimental and simulated melt pools. Finally, the ANSYS solution was compared with a new set of dynamic meshing finite element analysis algorithms running in Matlab. It was found that these new algorithms were significantly faster than their ANSYS counterparts for solving problems using a dynamic mesh.

Keywords

SLM Dynamic mesh modelling ANSYS

Get full access to this article

View all access options for this article.

References

Gibson

, Rosen

and Stucker

: ‘Additive manufacturing technologies’; 2010, New York, Springer.

Scott

, Gupta

, Weber

, Newsome

, Wohlers

and Caffrey

: Sci. Technol. Policy Inst., 2012, 1–29.

Kruth

J.-P

, Froyen

, Van Vaerenbergh

, Mercelis

, Rombouts

and Lauwers

: J. Mater. Process. Technol., 2004, 149, (1), 616–622.

Kruth

J.-P

, Mercelis

, Van Vaerenbergh

, Froyen

and Rombouts

: Rapid Prototyp. J., 2005, 11, (1), 26–36.

Taylor

: ‘Direct laser sintering of stainless steel: thermal experiments and numerical modelling’, PhD thesis, The University of Leeds, UK, 2004.

Ibraheem

, Derby

and Withers

: ‘Thermal and residual stress modelling of the selective laser sintering process’, Materials research society symposium proceedings, 47–52; 2003, Cambridge, Cambridge University Press.

Kolossov

, Boillat

, Glardon

, Fischer

and Locher

: Int. J. Mach. Tools Manuf., 2004, 44, (2), 117–123.

Zhang

, Cai

, Liu

, Zhang

and Li

: Int. J. Adv. Manuf. Technol., 2010, 51, (5–8), 649–658.

Roberts

, Wang

, Esterlein

, Stanford

and Mynors

: Int. Mach. Tools Manuf., 2009, 49, (12), 916–923.

10.

Song

, Dong

, Liao

and Coddet

: Int. J. Adv. Manuf. Technol., 2012, 61, (9–12), 967–974.

11.

Cervera

GBM

and Lombera

: Rapid Prototyp. J., 1999, 5, (1), 21–26.

12.

Dai

and Shaw

: Acta Mater., 2005, 53, (18), 4743–4754.

13.

Dong

, Makradi

, Ahzi

and Remond

: J. Mater. Process. Technol., 2009, 209, (2), 700–706.

14.

Gusarov

, Yadroitsev

, Bertrand

and Smurov

: Appl. Surf. Sci., 2007, 254, (4), 975–979.

15.

Shellabear

and Nyrhilä

: ‘Laser assisted netshape engineering 4, Proceedings of the 4th LANE’, Erlangen, Germany, September 2004, Meisenbach Verlag, 21–24.

16.

Childs

, Hauser

and Badrossamay

: CIRP Ann.-Manuf. Technol., 2004, 53, (1), 191–194.

17.

Patil

, Pal

and Stucker

: ‘A new finite element solver using numerical eigen modes for fast simulation of additive manufacturing processes’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.

18.

Pal

, Patil

, Zeng

and Stucker

: J. Manuf. Sci. Eng., 2014, 136, (6), 061022.

19.

Nikoukar

, Patil

, Pal

and Stucker

: ‘Methods for enhancing the speed of numerical calculations for the prediction of the mechanical behavior of parts made using additive manufacturing’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.

20.

Rombouts

, Kruth

J.-P

and Froyen

: Proc. of TMS: Fabrication, materials, processing and properties, 397–404, Vol. 1; 2009, Warrendale, PA, USA, TMS.

21.

Attar

: ‘Simulation of selective electron beam melting processes’, PhD thesis, University of Erlangen-Nuremberg, Erlangen, Germany, 2011.

22.

Körner

, Bauereiß

and Attar

: Modell. Simul. Mater. Sci. Eng., 2013, 21, (8), 085011.

23.

Dowden

: ‘The mathematics of thermal modeling: an introduction to the theory of laser material processing’; 2001, Boca Raton, Florida, USA, CRC Press.

24.

A. M. APDL, ANSYS Release 13, Canonsburg, PA, USA, 2010.

25.

Mills

: ‘Recommended values of thermophysical properties for selected commercial alloys’; 2002, Sawston, Cambridge, UK, Woodhead Publishing.

26.

Fischer

, Locher

, Romano

, Weber

H.-P

, Kolossov

and Glardon

: Int. J. Mach. Tools Manuf., 2004, 44, (12), 1293–1296.

27.

Zeng

, Pal

and Stucker

: ‘A review of thermal analysis methods in laser sintering and selective laser melting’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2012, University of Texas at Austin, 796.

28.

Verhaeghe

, Craeghs

, Heulens

and Pandelaers

: Acta Mater., 2009, 57, (20), 6006–6012.

29.

Cook

: ‘Concepts and applications of finite element analysis’; 2007, Hoboken, NJ, USA, Wiley.

30.

Huang

and Russell

RRD

: ‘Adaptive moving mesh methods’; 2011, Berlin, Heidelberg, Germany, Springer Science+ Business Media.

31.

C. ANSYS, Release 13·0-User Manual, Canonsburg, PA, USA, 2010.

32.

Matsumoto

, Shiomi

, Osakada

and Abe

: Int. J. Mach. Tools Manuf., 2002, 42, (1), 61–67.

33.

Zeng

, Pal

, Patilal

and Stucker

: ‘A new dynamic mesh method applied to the simulation of selective laser melting’, Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.