The effect of aging treatment on fracture toughness in Mg–6Zn–1Mn (wt-) was investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, scanning transmission electron microscopy, uniaxial tensile and fracture toughness tests, respectively. The results showed that the fracture toughness of Mg–6Zn–1Mn alloy can be enhanced by aging treatment. The fracture toughness and strength showed a reverse trend in single aged and double aged alloy. Synergetic effect of fine grains and precipitates improved the fracture toughness more sharply than aging treatment. The precipitate free zones and grain boundary precipitates made the largest contribution to the reduction of toughness. Under as extruded and aged conditions, the main origins of cracks were elastic incompatibility and plastic deformation.
LuoAA: ‘Magnesium casting technology for structural applications’, J. Magnes. Alloy, 2013, 1, (1), 2–22.
2.
AkbaripanahF, Fereshteh-SanieeF, MahmudiR and KimHK: ‘The influences of extrusion and equal channel angular pressing (ECAP) processes on the fatigue behavior of AM60 magnesium alloy’, Mater. Sci. Eng. A, 2013, A565, (1), 308–316.
3.
BaeDH, KimSH, KimDH and KimWT: ‘Deformation behavior of Mg–Zn–Y alloys reinforced by icosahedral quasicrystalline particles’, Acta Mater., 2002, 50, (9), 2343–2356.
4.
SomekawaH, OsawaY and MukaiT: ‘Effect of solid-solution strengthening on fracture toughness in extruded Mg–Zn alloys’, Scr. Mater., 2006, 55, (7), 593–596.
5.
SomekawaH, SinghA and MukaiT: ‘Effect of precipitate shapes on fracture toughness in extruded Mg-Zn-Zr magnesium alloys’, J. Mater. Res., 2007, 22, (4), 965–973.
6.
SomekawaH, SinghA and MukaiT: ‘High fracture toughness of extruded Mg–Zn–Y alloy by the synergistic effect of grain refinement and dispersion of quasicrystalline phase’, Scr. Mater., 2007, 56, (12), 1091–1094.
7.
SomekawaH and MukaiT: ‘Effect of texture on fracture toughness in extruded AZ31 magnesium alloy’, Scr. Mater., 2005, 53, (5), 541–545.
8.
SomekawaH and MukaiT: ‘Effect of grain refinement on fracture toughness in extruded pure magnesium’, Scr. Mater., 2005, 53, (9), 1059–1064.
9.
SomekawaH, OsawaY, SinghA and MukaiT: ‘Effect of precipitate volume fraction on fracture toughness of extruded Mg–Zn alloys’, J. Mater. Res., 2008, 23, (4), 1128–1135.
10.
YuanSP, LiuG, WangRH, ZhangGJ, PuX, SunJ and ChenKH: ‘Effect of precipitate morphology evolution on the strength–toughness relationship in Al–Mg–Si alloys’, Scr. Mater., 2009, 60, (12), 1109–1112.
11.
ZhangE, YinD, XuL, YangL and YangK: ‘Microstructure, mechanical and corrosion properties and biocompatibility of Mg–Zn–Mn alloys for biomedical application’, Mater. Sci. Eng. C, 2009, C29, (3), 987–993.
12.
YinD, ZhangE and ZengS: ‘Effect of Zn on mechanical property and corrosion property of extruded Mg–Zn–Mn alloy’, Trans. Nonferr. Met. Soc., 2008, 18, (4), 763–768.
13.
ParkSS, BaeGT, KangDH, JungI, ShinKS and KimNJ: ‘Microstructure and tensile properties of twin-roll cast Mg–Zn–Mn–Al alloys’, Scr. Mater., 2007, 57, (9), 793–796.
14.
ParkSS, OhYS, KangDH and KimNJ: ‘Microstructural evolution in twin-roll strip cast Mg–Zn–Mn–Al alloy’, Mater. Sci. Eng. A, 2007, A449, (3), 352–355.
15.
Ben-HamuG, EliezerD and ShinK S: ‘The role of Si and Ca on new wrought Mg–Zn–Mn based alloy’, Mater. Sci. Eng. A, 2007, A447, (1), 35–43.
16.
QiFG, ZhangDF, ZhuZT, XuXX and ShiGL: ‘Effect of heat treatment on microstructure and mechanical properties of extruded ZM61 magnesium alloy’, Mater. Sci. Technol., 2012, 28, (12), 1426–1433.
17.
WeiLY, DunlopGL and WestengenH: ‘Precipitation hardening of Mg–Zn and Mg–Zn–RE alloys’, Metall. Mater. Trans. A, 1995, 26A, (7), 1705–1716.
18.
ClarkJB: ‘Transmission electron microscopy study of age hardening in a Mg–5 wt. Zn alloy’, Acta Metall., 1965, 13, (12), 1281–1289.
19.
BrownKR and BarattaFI: ‘Overview on chevron-notch fracture test experience: metals and non-metals’, Proc. Symp. on ‘Chevron-notch fracture test experience: metals and non-metals’, Indianapolis, IN, USA, May 1991, ASTM, Paper 1.
20.
GrantTJ, WeberL and MortensenA: ‘Plasticity in Chevron-notch fracture toughness testing’, Eng. Fract. Mech., 2000, 67, (3), 263–276.
21.
LynchSP, WanhillRJH, ByrnesRT and BrayGH: ‘Fracture toughness and fracture modes of aerospace aluminum–lithium alloys’, in‘Aluminum-lithium alloys’, (ed. PrasadN E et al.), 1st edn, 415–455; 2014, Boston, MA, Butterworth-Heinemann.
22.
GaoX and NieJF: ‘Characterization of strengthening precipitate phases in a Mg-Zn alloy’, Scr. Mater., 2007, 56, (8), 645–648.
23.
PanH, PanF, WangX, PengJ, SheJ, ZhaoC, HuangQ, SongK and GaoZ: ‘High conductivity and high strength Mg–Zn–Cu alloy’, Mater. Sci. Technol., 2014, 30, (7), 759–764.
24.
NieJ: ‘Precipitation and hardening in magnesium alloys’, Metall. Mater. Trans. A, 2012, 43A, (11), 3891–3939.
25.
Oh-ishiK, HonoK and ShinKS: ‘Effect of pre-aging and Al addition on age-hardening and microstructure in Mg–6 wt Zn alloys’, Mater. Sci. Eng. A, 2008, A496, (1–2), 425–433.
26.
SasakiTT, Oh-ishiK, OhkuboT and HonoK: ‘Enhanced age hardening response by the addition of Zn in Mg-Sn alloys’, Scr. Mater., 2006, 55, (3), 251–254.
27.
OguraT, HirosawaS, CerezoA and SatoT: ‘Atom probe tomography of nanoscale microstructures within precipitate free zones in Al-Zn-Mg(-Ag) alloys’, Acta Mater., 2010, 58, (17), 5714–5723.
28.
XuC, ZhengMY, WuK, WangED, FanGH, XuSW, KamadoS, LiuXD, WangGJ and LvXY: ‘Effect of ageing treatment on the precipitation behaviour of Mg–Gd–Y–Zn–Zr alloy’, J. Alloys Compd, 2013, 550, 50–56.
29.
YuanSP, LiuG, WangRH, ZhangGJ, PuX, SunJ and ChenKH: ‘Aging-dependent coupling effect of multiple precipitates on the ductile fracture of heat-treatable aluminum alloys’, Mater. Sci. Eng. A, 2009, A499, (1–2), 387–395.
30.
YuanSP, LiuG, WangRH, PuX, ZhangG, SunJ and ChenK: ‘Coupling effect of multiple precipitates on the ductile fracture of aged Al–Mg–Si alloys’, Scr. Mater., 2007, 57, (9), 865–868.
31.
FanZ Y: ‘The grain size dependence of ductile fracture toughness of polycrystalline metals and alloys’, Mater. Sci. Eng. A, 1995, A191, (1–2), 73–83.
