Effect of Zn on the microstructure, age hardening response and mechanical properties of Mg–3Sn–1Al alloy which is immediately aged at 180°C after extrusion process (T5) was investigated. It was found that the Zn can refine the microstructure, remarkably improve the aging response with the peak hardness increases to 75 HV and the time to peak hardness reduces from ∼110 to ∼60 h, which is attributed to the solid solution hardening of Al, Zn and an amount of finer Mg2Sn precipitates. The as aged Mg–3Sn–2Zn–1Al alloy exhibits better mechanical property at room temperature or 150°C than that of Mg–3Sn–1Al alloy, which is ascribed to the fine grained microstructure and thermally stable Mg2Sn particles dispersed at grain boundaries and in the matrix.
KondoriB and MahmudiR: ‘Impression creep characteristics of a cast Mg alloy’, Metall. Mater. Trans. A, 2009, 40A, 2007–2015.
4.
Nayeb-HashemiAA and ClarkJB: ‘Phase diagrams of binary magnesium alloys’, 1988, Materials Park, OH, ASM International.
5.
KangDH, ParkSS and KimNJ: ‘Development of creep resistant die cast Mg–Sn–Al–Si alloy’, Mater. Sci. Eng. A, 2005, A413–A414, 555–560.
6.
ZhangL, CaoZY, LiuYB, SuGH and ChengLR: ‘Effect of Al content on the microstructures and mechanical properties of Mg–Al alloys’, Mater. Sci. Eng. A, 2009, A508, (1–2), 129–133.
7.
MendisCL, BettlesCJ, GibsonMA and HutchinsonCR: ‘An enhanced age hardening response in Mg–Sn based alloys containing Zn’, Mater. Sci. Eng. A, 2006, A435–A436, 163–171.
GibsonMA, FangX, BettlesCJ and HutchinsonCR: ‘The effect of precipitate state on the creep resistance of Mg–Sn alloys’, Scr. Mater., 2010, 63, 899–902.
10.
ParkSS and YouBS: ‘Low-temperature superplasticity of extruded Mg–Sn–Al–Zn alloy’, Scr. Mater., 2011, 65, 202–205.
11.
SasakiTT, YamamotoK, HonmaT, KamadoS and HonoK: ‘A high-strength Mg–Sn–Zn–Al alloy extruded at low temperature’, Scr. Mater., 2008, 59, 1111–1114.
12.
van der PlankenJ: J. Mater. Sci. Lett., 1967, 4, 927–929.
13.
SasakiTT, Oh-IshiK, OhkuboT and HonoK: ‘Effect of double aging and microalloying on the age hardening behavior of a Mg–Sn–Zn alloy’, Mater. Sci. Eng. A, 2011, A530, 1–8.
14.
SasakiTT, Oh-IshiK, OhkuboT and HonoK: ‘Enhanced age hardening response by the addition of Zn in Mg–Sn alloys’, Scr. Mater., 2006, 55, (3), 251–254.
15.
ChenJH, ChenZH, YanHG, ZhangFQ and KunL: ‘Effects of Sn addition on microstructure and mechanical properties of Mg–Zn–Al alloys’, J. Alloys Compd, 2008, 461, 209–215.
16.
ElsayedaFR, SasakiTT, MendisCL, OhkuboT and HonoK: ‘Compositional optimization of Mg–Sn–Al alloys for higher age hardening response’, Mater. Sci. Eng. A, 2013, A566, 22–29.
17.
HonoK, MendisCL, SasakiTT and Oh-IshiK: ‘Towards the development of heat-treatable high-strength wrought Mg alloys’, Scr. Mater., 2010, 63, 710–715.
18.
KimBH, JeonJJ, ParkKC, ParkBG, ParkYH and ParkIM: ‘Microstructural characterization and mechanical properties of Mg–xSn–5Al–1Zn alloys’, Int. J. Cast Met. Res.2008, 21, (1–4), 186–192.
19.
ParkSS, TangWN and YouBS: ‘Microstructure and mechanical properties of an indirect-extruded Mg–8Sn–1Al–1Zn alloy’, Mater. Lett., 2010, 64, 31–34.
20.
LiuHM, ChenYG, TangYB, WeiSH and NiuG: ‘The microstructure, tensile properties, and creep behavior of as-cast Mg–(1–10)Sn alloys’, J. Alloys Compd, 2007, 440, 122–126.
21.
ChengWL, ParkSS, YouBS and KooBH: ‘Microstructure and mechanical properties of binary Mg–Sn alloys subjected to indirect extrusion’, Mater. Sci. Eng. A, 2010, A527, 4650–4653.
22.
LeeYC, DahleAK and StjohnDH: ‘The role of solute in grain refinement of magnesium’, Metall. Mater. Trans. A, 2000, 31A, 2895–2906.
23.
KimYM, WangL and YouBS: ‘Grain refinement of Mg–Al cast alloy by the addition of manganese carbonate’, J. Alloys Compd, 2010, 490, 695–699.
24.
DongXG, FuJW, WangJ and YangYS: ‘Microstructure and tensile properties of as-cast and as-aged Mg–6Al–4Zn alloys with Sn addition’, Mater. Des., 2013, 51, 567–574.
25.
RabkinE: ‘Zener drag in the case of anisotropic grain boundary energy’, Scr. Mater., 1998, 39, 1631–1637.
26.
LiWB and EasterlingKE: ‘The influence of particle shape on zener drag’, Acta Metall. Mater., 1990, 38, 1045–1052.
27.
ZhaoDQ, DongQ, ZhouJX, LiuYT, DongXG, WangJ and YangYS: ‘Microstructure and mechanical properties of Mg–4Zn–2Al–2Sn alloys extruded at low temperatures’, Acta Metall. Sin., 2014, 50, (1), 41–48.
28.
SonH.-T, LeeJ.-B, JeongH.-G and KonnoTJ: ‘Effects of Al and Zn additions on mechanical properties and precipitation behaviors of Mg–Sn alloy system’, Mater. Lett., 2011, 65, 1966–1969.
29.
EmburyJD and NicholsonRB: ‘The nucleation of precipitates: the system Al–Zn–Mg’, Acta Metall., 1965, 13, 403–417.
30.
ZhangJ, YuanFQ and DuY: ‘Enhanced age-strengthening by two-step progressive solution treatment in an Mg–Zn–Al–Re alloy’, Mater. Des., 2013, 52, 332–336.
31.
PanH, PanF, WangX, PengJ, SheJ, ZhaoC, HuangQ, SongK and GaoZ: ‘High conductivity and high strength Mg–Zn–Cu alloy’, Mater. Sci. Technol., 2014, 30, (7), 759–764.
32.
Oh-IshiK, HonoK and ShinK: ‘Effect of pre-aging and Al addition on age-hardening and microstructure in Mg–6wt Zn alloys’, Mater. Sci. Eng. A, 2008, A496, (1), 425–433.
33.
HenesS and GeroldV: ‘Roentgenographic investigation of the separation processes in magnesium–lead and magnesium–zinc alloys’, Z. Metallkd, 1962, 53, 743–751.
34.
YangZ, LiJ, ZhangJ, LorimerGW and RobsonJ: ‘Review on research and development of magnesium alloys,’Acta Metall. Sin., 2008, 21, (5), 313–328.
35.
BohlenJ, DobronP, SwiostekJ, LetzigD, ChmelíkF, LukacP and KainerKU: ‘On the influence of the grain size and solute content on the AE response of magnesium alloys tested in tension and compression’, Mater. Sci. Eng. A, 2007, A462, 302–306.
36.
KimHK, LeeYI and ChungCS: ‘Fatigue properties of a fine-grained magnesium alloy produced by equal channel angular pressing’, Scr. Mater., 2005, 52, (6), 473–477.
37.
FangDQ, MaN, CaiKL, CaiXC, ChaiYS and PengQM: ‘Age hardening behaviors, mechanical and corrosion properties of deformed Mg–Mn–Sn sheets by pre-rolled treatment’, Mater. Des., 2014, 54, 72–78.
38.
YamashitaA, HoritaZ and LangdonTG: ‘Improving the mechanical properties of magnesium and a magnesium alloy through severe plastic deformation’, Mater. Sci. Eng. A, 2001, A300, 142–147.
39.
EmleyEF: ‘Principles of magnesium technology’; 1966, New York, Pergamon.
40.
HaroshS, MilleL, LeviG and BambergerM: ‘Microstructure and properties of Mg–5·6Sn–4·4Zn–2·1Al alloy’, J. Mater. Sci., 2007, 42, 9983–9989.
41.
XiaoWL, JiaSS, WangLD, WuYM and WangLM: ‘Effects of Sn content on the microstructure and mechanical properties of Mg–7Zn–5Al based alloys’, Mater. Sci. Eng. A, 2010, A527, 7002–7007.
42.
PanXQ, ChenJH, YanHG, SuB, WeiJY and FanC: ‘Effects of Zn/Sn mass ratio on microstructure and mechanical properties of Mg–Zn–Sn–Al–Ca alloys’, Mater. Sci. Technol., 2013, 29, (2), 169–176.
43.
LeeSH, LeeSH and KimDH: ‘Effect of Y, Sr, and Nd additions on the microstructure and microfracture mechanism of squeeze-cast AZ91-X magnesium alloys’, Metall. Mater. Trans. A, 1998, 29A, 1221–1235.
44.
JayalakshmiS, KailasSV and SeshanS: ‘Tensile behavior of squeeze cast AM100 magnesium alloy and its Al2O3 fibre reinforced composites’, Composites Part A, 2002, 33A, 1135–1140.
45.
ArztE and AshbyMF: ‘Threshold stresses in materials containing dispersed particles’, Scr. Metall., 1982, 16, 1285–1290.
46.
WeiSH, ChenYG, TangYB, LiuHM, XiaoSF, NiuGZhangXP and ZhaoYH: ‘Compressive creep behavior of as-cast and aging-treated Mg–5 wtSn alloys’, Mater. Sci. Eng. A, 2008, A492, 20–23.
47.
NayyeriG and MahmudiR: ‘Enhanced creep properties of a cast Mg–5Sn alloy subjected to aging-treatment’, Mater. Sci. Eng. A, 2010, A527, 4613–4618.
