High speed rolling (HSR) of 1000 m min−1 was employed to successfully roll AZ31 alloy in one pass with 65 reduction in thickness at 300 and 450°C. The rollability, texture and microstructure after HSR, in comparison with low speed rolling (15 m min−1), improved significantly. It is suggested that the double peak and weaker basal texture obtained after HSR are attributed to the activation of compression and double twins. After annealing, the double peak basal texture is replaced by a single peak one, which may be due to preferential grain growth of basal grains.
AvedesianHBM: ‘ASM specialty handbook. Magnesium and magnesium alloys’; 2000, Materials Park, OH, ASM International.
2.
ShamsiM, SanjariM, HanzakiAZ: ‘Study of fractional softening of AZ31 magnesium alloy under multistage hot deformation’,Mater. Sci. Technol., 2009, 25, (8), 1039–1045.
3.
AgnewSR, YooMH, ToméCN: ‘Application of texture simulation to understanding mechanical behavior of Mg and solid solution alloys containing Li or Y’,Acta Mater., 2001, 49, (20), 4277–4289.
4.
GaliyevA, KaibyshevR, GottsteinG: ‘Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK60’,Acta Mater., 2001, 49, (7), 1199–1207.
5.
MwembelaA, KonoplevaEB, McQueenHJ: ‘Microstructural development in Mg alloy AZ31 during hot working’,Scr. Mater., 1997, 37, (11), 1789–1795.
6.
AgnewSR, DuyguluO: ‘Plastic anisotropy and the role of non-basal slip in magnesium alloy AZ31B’,Int. J. Plast., 2005, 21, (6), 1161–1193.
7.
BarnettMR: ‘A Taylor model based description of the proof stress of magnesium AZ31 during hot working’,Metall. Mater. Trans. A: Phys. Metall. Mater. Sci., 2003, 34, (9), 1799–1806.
8.
MackenzieLWF, PekguleryuzM: ‘The influences of alloying additions and processing parameters on the rolling microstructures and textures of magnesium alloys’,Mater. Sci. Eng. A, 2008, A480, (1–2), 189–197.
9.
KonH, SakaiT, UtsunomiyaH, MinamiguchiS: ‘Deformation and texture evolution during high-speed rolling of AZ31 magnesium sheets’,Mater. Trans., 2007, 48, (8), 2023–2027.
10.
UtsunomiyaH, SakaiT, MinamiguchiS, KohH:‘High-speed heavy rolling of magnesium alloy sheets’‘Magnesum technology 2006’(, LuoA A, et al..), 201–204; 2006, Warrendale, PA, TMS.
11.
HamadaG, SakaiT, UtsunomiyaH: ‘Effect of rolling speed on deformability and microstructure in rolling of AZ31B magnesium alloy’, Adv. Mater. Res., 2010, 227–231.
12.
SakaiT, WatanabeY, UtsunomiyaH: ‘Microstructure and texture of AZ80 magnesium alloy sheet rolled by high speed warm rolling’, Mater. Sci. Forum, 2009, 483–486.
13.
BarnettMR, NaveMD, BettlesCJ: ‘Deformation microstructures and textures of some cold rolled Mg alloys’,Mater. Sci. Eng. A, 2004, A386, (1–2), 205–211.
14.
YanH, XuSW, ChenRS, KamadoS, HonmaT, HanEH: ‘Twins, shear bands and recrystallization of a Mg–2·0Zn–0·8Gd alloy during rolling’,Scr. Mater., 2011, 64, (2), 141–144.
15.
SandlöbesS, ZaeffererS, SchestakowI, YiS, Gonzalez-MartinezR: ‘On the role of non-basal deformation mechanisms for the ductility of Mg and Mg-Y alloys’,Acta Mater., 2011, 59, (2), 429–439.
16.
LiH, HsuE, SzpunarJ, UtsunomiyaH, SakaiT: ‘Deformation mechanism and texture and microstructure evolution during high-speed rolling of AZ31B Mg sheets’,J. Mater. Sci., 2008, 43, (22), 7148–7156.
17.
CottamR, RobsonJ, LorimerG, DavisB: ‘Dynamic recrystallization of Mg and Mg-Y alloys: Crystallographic texture development’,Mater. Sci. Eng. A, 2008, A485, (1–2), 375–382.
LeeBH, BangW, AhnS, LeeCS: ‘Effects of temperature and strain rate on the high-temperature workability of strip-cast Mg–3Al–1Zn alloy’,Metall. Mater. Trans. A: Phys. Metall. Mater. Sci., 2008, 39, (6), 1426–1434.
20.
SanjariM, FarzadfarSA, YueS, EssadiqiE:‘Very high strain rate deformation of AZ31B Mg alloys using split Hopkinson pressure bar’‘Magnesium technology 2010’(, AgnewS, et al..), 481–486; 2010, Warrendale, PA, TMS.
21.
YiS, SchestakowI, ZaeffererS: ‘Twinning-related microstructural evolution during hot rolling and subsequent annealing of pure magnesium’,Mater. Sci. Eng. A, 2009, A516, (1–2), 58–64.
22.
SanjariM, FarzadfarSA, JungIH, EssadiqiE, YueS: ‘Influence of strain rate on hot deformation behaviour and texture evolution of AZ31B’,Mater. Sci. Technol., 2012, 28, (4), 437–447.
23.
MartinÉ, JonasJJ: ‘Evolution of microstructure and microtexture during the hot deformation of Mg-3 Al’,Acta Mater., 2010, 58, (12), 4253–4266.
24.
AbdessameudS, BradaiD: ‘Microstructure and texture evolution in hot rolled and annealed magnesium alloy TRC AZ31’,Can. Metall. Q., 2009, 48, (4), 433–442.
