The hot ductility of Allvac 718Plus for different solution heat treatments (954°C–15 h, 954°C–1 h, 982°C–1 h and 1050°C–3 h+954°C–1 h) has been investigated using Gleeble testing. Substantial variations in the microstructure among the heat treatments affected the Gleeble test hot ductility only to a very limited extent. Constitutional liquation of the NbC phase was found to be the main cause for the poor ductility at high testing temperatures in the on-heating cycle as well as at the lower temperatures on-cooling. Grain boundary δ phase was seen to assist the constitutional liquation of the NbC phase. Based on established evaluation criteria for Gleeble ductility testing, a ranked indicator for weldability is suggested.
ZicklerGA, RadisR, SchnitzerR, KozeschnikE, StockingerM, LeitnerH: ‘The precipitation behavior of superalloy ATI Allvac 718Plus’,Adv. Eng. Mater., 2010, 12, (3), 176–183.
3.
XieX, WangG, DongJ, XuC, CaoWD, KennedyR: ‘Structure stability study on a newly developed nickel-base superalloy-Allvac 718Plus’, in ‘Superalloys 718, 625, 706 and various derivatives’, (ed. , LoriaE A), 179–191; 2005, Warrendale, PA, TMS.
4.
AnderssonJ, HatamiS, SjöbergG: ‘Notch sensitivity and intergranular crack growth in the Allvac 718Plus superalloy’, Proc. 18th Int. Symp. on ‘Air breathing engines’, International Association of Airbreathing Engines, Beijing, China, September 2007, Paper 1293.
5.
QianM: ‘An investigation of the repair weldability of Waspaloy and alloy 718’, PhD thesis, The Ohio State University, Columbus, OH, USA, 2002.
6.
VishwakarmaK: ‘Microstructural analysis of weld cracking in 718 Plus superalloy’, PhD thesis, University of Manitoba, Winnipeg, MB, Canada, 2007.
7.
RadhakrishnanB, ThompsonRG: ‘A phase diagram approach to study liquation cracking in alloy 718’,Metall. Trans. A, 1991, 22A, 887–902.
8.
BoucherC, VarelaD, DadianM, GranjonH: ‘Hot cracking and recent progress in the weldability of the nickel alloys Inconel 718 and Waspaloy’,Rev. Metall., 1976, 73, 817–831.
9.
VincentR: ‘Precipitation around welds in the nickel-base superalloy Inconel 718’,Acta Metall., 1985, 33, 1205–1216.
10.
AnderssonJ, SjöbergGP, ViskariL, MaheshMC: ‘Effect of different solution heat treatments on the hot ductility of superalloys. Part 1 – alloy 718’, Mater. Sci. Technol., 2012, 28, 609–619.
11.
‘Aerospace material specification no. AMS 5441’, SAE International, Warrendale, PA, USA, 2006.
12.
AnderssonJ, HatamiS: ‘Notch sensitivity and grain boundary embrittlement in Allvac 718Plus – effect of δ-phase morphology’, Master's thesis, The Royal Institute of Technology, Stockholm, Sweden, 2006.
13.
ViskariL, CaoY, NorellM, SjöbergG, StillerK: ‘Grain boundary microstructure and fatigue crack growth in Allvac 718Plus superalloy’,Materials Science and Engineering A, 2011, 5282570–2580.
14.
LippoldJC, KiserSD, DuPontJN: ‘Welding metallurgy and weldability of nickel-base superalloys’; 2009, Hoboken, NJ, John Wiley & Sons.
YeniscavichW: ‘Correlation of hot ductility curves with cracking during welding’, Proc. Symp. on ‘Methods of high alloy weldability evaluation’, New York, USA, April 1969, WRC, 2–12.
17.
LundinCD, QiaoCYP, GillTPS, GoodwinGM: ‘Hot ductility and hot cracking behavior of modified 316 stainless steels designed for high-temperature service’,Weld. J., 1993, 72, 189–200.
18.
CaoWD: ‘Solidification and solid state phase transformation of Allvac 718Plus alloy’, in ‘Superalloys 718, 625, 706 and various derivatives’, (ed. , LoriaE A), 165–177; 2005, Warrendale, PA, TMS.
VishwakarmaKR, RichardsNL, ChaturvediMC: ‘Microstructural analysis of fusion and heat affected zones in electron beam welded Allvac 718 Plus superalloy’,Mater. Sci. Eng. A, 2008, A480, 517–528.
21.
VishwakarmaKR, ChaturvediMC: ‘Effect of band P on HAZ microfissuring of Allvac 718Plus superalloy’,Mater. Sci. Technol., 2009, 25, (3), 351–359.
22.
OjoOA: ‘Letter to the editor’,Mater. Sci. Technol., 2011, 27, (10), 1610–1612.
23.
BenhadadS, RichardsNL, ChaturvediMC: ‘The influence of minor elements on the weldability of an Inconel 718-type superalloy’,Metall. Mater. Trans. A, 2002, 33A, 2005–2017.
24.
DieterGE: ‘Mechanical metallurgy, SI metric edition’; 1988, Singapore, McGraw-Hill.
25.
AnderssonJ, SjöbergG: ‘Repair welding of wrought superalloys: Alloy 718, Allvac 718Plus and Waspaloy’,Sci. Technol. Weld. Join., 2012, 17, 49–59.
