In this article, the variation of hardness in cross-section of X52 microalloyed steel joints before and after post-weld heat treatment and also the relationship of hardness with ultimate tensile strength, yield strength and microstructure have been investigated. For this purpose, the specimens were prepared in two conditions of as welded and post-weld heat treated, and the hardness maps of their cross-section were provided. Then, some equations were suggested to correlate the obtained hardness with the grain size and tensile and yield strengths. The equations made it possible to predict tensile and yield strengths with high accuracy. According to the results, the maximum hardness and strength belong to the weld junction. Normalisation of the joints at 950°C reduced significantly the hardness difference (and also the strength difference) in various joint areas and homogenised the microstructure considerably. The grain size distribution was also modelled acceptably for the post-weld heat treated joint, and the grain size map was obtained.
SunJ.-Q., DaiH. and ZhangY.-C.: ‘Research on mathematical model of thermal deformation resistance of X80 pipeline steel’, Mater. Des., 2011, 32, (3), 1612–1616. doi: 10.1016/j.matdes.2010.08.045
2.
ÇölM. and YılmazM.: ‘The determination of heat treatment parameters of X52 microalloyed steel after high frequency induction welding’, Mater. Des., 2006, 27, (6), 507–512. doi: 10.1016/j.matdes.2004.11.025
3.
ASM Handbook Committee: ‘Welding, brazing, and soldering’, 1315; 1993, Metals Park, OH, ASM International.
4.
YanP., GüngörÖ. E., ThibauxP., LiebeherrM. and BhadeshiaH. K. D. H.: ‘Tackling the toughness of steel pipes produced by high frequency induction welding and heat-treatment’, Mater. Sci. Eng. A, 2011, A528, (29–30), 8492–8499. doi: 10.1016/j.msea.2011.07.034
5.
GhazanfariH., NaderiM., IranmaneshM., SeydiM. and PoshtebanA.: ‘A comparative study of the microstructure and mechanical properties of HTLA steel welds obtained by the tungsten arc welding and resistance spot welding’, Mater. Sci. Eng. A, 2012, A534, 90–100. doi: 10.1016/j.msea.2011.11.046
6.
NaderiM., Saeed-AkbariA. and BleckW.: ‘Quantitative and qualitative investigation of the heterogeneous microstructures using surface hardness mapping and dilatation data’, Mater. Lett., 2008, 62, (6–7), 1132–1135. doi: 10.1016/j.matlet.2007.07.068
7.
ParkerJ. D. and SiefertJ. A.: ‘Evaluation of options for weld repair of grade 91 piping and components: metallographic characterisation’, Sci. Technol. Weld. Join., 2013, 18, (6), 507–517. doi: 10.1179/1362171813Y.0000000132
8.
SongH. Y., EvansG. M. and BabuS. S.: ‘Effect of microstructural heterogeneities on scatter of toughness in multi-pass weld metal of C–Mn steels’, Sci. Technol. Weld. Join., 2014, 19, (5), 376–384. doi: 10.1179/1362171814Y.0000000194
9.
VitekJ. M. and BabuS. S.: ‘Multiscale characterisation of weldments’, Sci. Technol. Weld. Join., 2011, 16, (1), 3–11. doi: 10.1179/1362171810Y.0000000003
10.
WuX., BakerI., MillerM. K., MoreK. L., CaiZ. and ChenS.: ‘Microstructure and mechanical properties of two-phase Fe30Ni20Mn20Al30. Part I: microstructure’, J. Mater. Sci., 2013, 48, (21), 7435–7445. doi: 10.1007/s10853-013-7558-4
11.
RamjaunT. I., StoneH. J., KarlssonL., KelleherJ., OoiS. W., DalaeiK., KornmeierJ. R. and BhadeshiaH. K. D. H.: ‘Effects of dilution and baseplate strength on stress distributions in multipass welds deposited using low transformation temperature filler alloys’, Sci. Technol. Weld. Join., 2014, 19, (6), 461–467. doi: 10.1179/1362171814Y.0000000209
12.
KeehanE., KarlssonL., AndrénH.-O. and BhadeshiaH. K. D. H.: ‘Influence of carbon, manganese and nickel on microstructure and properties of strong steel weld metals. Part 3 – increased strength resulting from carbon additions’, Sci. Technol. Weld. Join., 2006, 11, (1), 19–24. doi: 10.1179/174329306X77858
13.
Della RovereC. A., RibeiroC. R., SilvaR., BaroniL. F. S., AlcântaraN. G. and KuriS. E.: ‘Microstructural and mechanical characterization of radial friction welded supermartensitic stainless steel joints’, Mater. Sci. Eng. A, 2013, A586, 86–92. doi: 10.1016/j.msea.2013.08.014
14.
GhazanfariH. and NadriM.: ‘Influence of welding parameters on microstructure and mechanical performance of resistance spot welded high strength steels’, Acta Metall. Sinica, 2013, 26, 635–640. doi: 10.1007/s40195-013-0076-1
15.
McWilliamsB. A., YuJ. H. and YenC.-F.: ‘Numerical simulation and experimental characterization of friction stir welding on thick aluminum alloy AA2139-T8 plates’, Mater. Sci. Eng. A, 2013, A585, 243–252. doi: 10.1016/j.msea.2013.07.073
16.
SiefertJ. A., LeisterB. M. and DuPontJ. N.: ‘Considerations in development of CCT diagrams for complex ferritic materials’, Mater. Sci. Technol., 2015, 31, (6), 651–660. doi: 10.1179/1743284714Y.0000000626
17.
HanholdB., BabuS. S. and ColaG.: ‘Investigation of heat affected zone softening in armour steels. Part 1 – phase transformation kinetics’, Sci. Technol. Weld. Join., 2013, 18, (3), 247–252. doi: 10.1179/1362171812Y.0000000100
18.
HanholdB., BabuS. S. and ColaG.: ‘Investigation of heat affected zone softening in armour steels. Part 2 – mechanical and microstructure heterogeneity’, Sci. Technol. Weld. Join., 2013, 18, (3), 253–260. doi: 10.1179/1362171812Y.0000000101
19.
MurrL. E.: ‘Correlating impact related residual microstructures through 2D computer simulations and microindentation hardness mapping: review’, Mater. Sci. Technol., 2012, 28, (9–10), 1108–1126. doi: 10.1179/1743284712Y.0000000008
20.
Kavousi SisiA. and MirsalehiS. E.: ‘Effect of post-weld heat treatment on microstructure and mechanical properties of X52 linepipe HFIW joints’, J. Mater. Eng. Perform., 2015, 24, (4), 1626–1633. doi: 10.1007/s11665-015-1423-3
21.
ASTM: ‘Standard test methods for determining average grain size’, ASTM E112, ASTM International, West Conshohocken, PA, USA, 2004.
22.
API: ‘Specification for line pipe’, API 5L, American Petroleum Institute, Washington, DC, USA, 2007.
23.
YanP.: ‘High frequency induction welding & post-welding heat treatment of steel pipes’, ‘PhD thesis, Girton College, Cambridge, UK’, 2011.
24.
MoonD. W., FondaR. W. and SpanosG.: ‘Microhardness variations in HSLA-100 welds fabricated with new ultra-low-carbon weld consumables’, Weld. J., 2000, 79, (10), 278.
25.
MoonD. W., LambrakosS. G., WongR. J. and MetzbowerE. A.: ‘Temperature, macrostructure and hardness in high strength low alloy steel welds, Sci’, Technol. Weld. Join., 2003, 8, (5), 334–339. doi: 10.1179/136217103225005561
26.
GüngörÖ. E., ThibauxP., LiebeherrM., BhadeshiaH. K. D. H. and YanP.: ‘Investigation into microstructure–toughness relation in high frequency induction welded pipes’, Proc. 8th Int. Pipeline Conf., Calgary, Alta, Canada, September–October, ASME, 1–9; 2010.
YanP., GuüngörÖ. E., ThibauxP. and BhadeshiaH. K. D. H.: ‘Crystallographic texture of induction-welded and heat-treated pipeline steel’, Adv. Mater. Res., 2010, 89, 651–656. doi: 10.4028/www.scientific.net/AMR.89-91.651
29.
SunL., ThomasM. J., WynneB. P., PalmiereE. J., MingardK. P. and RoebuckB.: ‘Mapping microstructure inhomogeneity using electron backscatter diffraction in 316L stainless steel subjected to hot plane strain compression tests’, Mater. Sci. Technol., 2010, 26, (12), 1477–1486. doi: 10.1179/026708310X12688283410280
30.
SatoY. S., UrataM., KokawaH. and IkedaK.: ‘Hall–Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys’, Mater. Sci. Eng. A, 2003, A354, (1–2), 298–305. doi: 10.1016/S0921-5093(03)00008-X
31.
CahoonJ. R., BroughtonW. H. and KutzakA. R.: ‘The determination of yield strength from hardness measurements’, Metall. Trans., 1971, 2, 1979–1983.
32.
CahoonJ. R.: ‘An improved equation relating hardness to ultimate strength’, Metall. Trans., 1972, 3, (11), 3040–3040. doi: 10.1007/BF02652880
33.
PavlinaE. J. and vanC. J.: ‘Tyne: Correlation of yield strength and tensile strength with hardness for steels’, J. Mater. Eng. Perform., 2008, 17, (6), 888–893. doi: 10.1007/s11665-008-9225-5
34.
ZhuM.-L. and XuanF.-Z.: ‘Correlation between microstructure, hardness and strength in HAZ of dissimilar welds of rotor steels, Mater’, Sci. Eng. A, 2010, A527, 4035–4042. doi: 10.1016/j.msea.2010.03.066
35.
YanP., GuüngörÖ. E., ThibauxP. and BhadeshiaH. K. D. H.: ‘Induction welding and heat treatment of steel pipes: evolution of crystallographic texture detrimental to toughness’, Sci. Technol. Weld. Join., 2010, 15, (2), 137–141. doi: 10.1179/136217109X12568132624163
