The influence of threaded and wear simulated (half thread) tools on the mechanical properties of dissimilar Al alloy friction stir spot welds is investigated. With lower tool rotational speed settings, the failure loads of Al 5754/Al 6111 lap joints made using a threaded tool were clearly higher than that of a half thread tool. However, the failure load of the joints made using a half thread tool increased when the tool rotational speed increased, and finally, as the rotational speed was further increased, the failure load became almost the same as the failure load of joints made using a threaded tool. In Al 5052/Al 6061 butt joints made using the threaded and half thread tools, the area of the stir zone on the bonded cross-section corresponded with the actual bonded region on the fracture surface. Therefore, the thread on the rotating pin has limited influence on the mechanical properties of the friction stir spot lap joints.
SakanoR, MurakamiK, YamashitaK, HyoeT, FujimotoM, InuzukaM, NaganoY, KashikiH: ‘Development of spot FSW robot system for automobile body members’, Proc. 3rd Int. Conf. on ‘Friction stir welding’, Kobe, Japan, September 2001, TWI,645–650.
2.
OkamotoK, HuntF, HiranoS: ‘Development of friction stir welding technique and machine for aluminum sheet metal assembly – friction stir welding of aluminum for automotive applications(2)-’, SAE Tech. Pap., 2005, 2005-01-1254.
3.
SuP, GerlichA, NorthTH: ‘Friction stir spot welding of aluminum and magnesium alloy sheets’, SAE Tech. Pap., 2005, 2005-01-1255.
4.
TanakaK, KumagaiM, YoshidaH: ‘Dissimilar joining of aluminum alloy and steel sheets by friction stir spot welding’, J. Jpn Inst. Light Met., 2006, 56, (6), 317–322.
5.
GerlichA, SuP, NorthTH: ‘Friction stir spot welding of mg-alloys for automotive applications’, Proc. Conf. Magnesium Technology 2005, San Francisco, CA, USA, February 2005, The Minerals, Metals & Materials Society, 383–388.
6.
PradoRA, MurrLE, SotoKF, McClureJC: ‘Self-optimization in tool wear for friction-stir welding of Al6061+20%Al2O3 MMC’, Mater. Sci. Eng. A, 2003, A349, 156–165.
7.
ShindoDJ, RiveraAR, MurrLE: ‘Shape optimization for tool wear in the friction-stir welding of cast Al359–20% SiC MMC’, J. Mater. Sci., 2002, 37, 4999–5005.
8.
FujiiH, CuiL, MaedaM, NogiK: ‘Friction stir welding of aluminum alloys using tool without screw’, Preprints Natl Meet. Jpn Weld. Soc., 2004, (75), 12–13.
9.
FujimotoM, KogaS, AbeN, SatoYS, KokawaH: ‘Analysis of plastic flow of the Al alloy lap joint produced by friction stir spot welding’, Q. J. Jpn Weld. Soc., 2008, 26, (1), 67–73.
10.
FujimotoM, WatanabeD, AbeN, SatoYS, KokawaH: ‘Effects of process time thread on tensile shear strength of Al alloy lap joint produced by friction stir spot welding’, Q. J. Jpn Weld. Soc., 2008, 26, (4), 253–258.
11.
SuP, GerlichA, NorthTH, BendzsakGJ: ‘Intermixing in dissimilar friction stir spot welding’, Metall. Mater. Trans. A, 2007, 38A, (3), 584–595.
12.
SakamuraM, OhishiK, TakeyasuY, TsumuraT, NakataK: ‘Development of friction stir spot welding for steel sheets. 1. Effects of the change of a tool shape’, Bull. Hiroshima Prefect. Technol. Res. Inst., 2008, 21, 1–8.
13.
ChoiDH, LeeCY, AhnBW, ChoiJH, YeonYM, SongK, ParkHS, KimYJ, YooCD, JungSB: ‘Friction wear evaluation of WC–Co alloy tool in friction stir spot welding of low carbon steel plates’, Int. J. Refract. Met. Hard Mater., 2009, 27, 931–936.
14.
AotaK, IkeuchiK: ‘Development of friction stir spot welding using rotating tool without probe and its application to low carbon steel plates’, Q. J. Jpn Weld. Soc., 2008, 26, (1), 54–60.
15.
TozakiY, UematsuY, TokajiK: ‘A newly developed tool without probe for friction stir spot welding and its performance’, J. Mater. Process. Technol., 2010, 210, 844–851.
16.
YinYH, SunN, NorthTH, HuSS: ‘Microstructures and mechanical properties in dissimilar AZ91/AZ31 spot welds’, Mater. Charact., 2010, 61, 1018–1028.
17.
BadarinarayanH, ShiY, LiX, OkamotoK: ‘Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets’, Int. J. Mach. Tools Manuf., 2009, 49, 814–823.
18.
BuffaaG, CampanileG, FratiniL, PriscoA: ‘Friction stir welding of lap joints -influence of process parameters on the metallurgical and mechanical properties-’, Mater. Sc. Eng. A, 2009, A519, 19–26.
19.
Unpublished research, Department of Materials Science and Engineering, University of Toronto, Toronto, Ont., Canada, 2010.
20.
YinYH, SunN, NorthTH, HuSS: ‘Influence of tool design on mechanical properties of AZ31 friction stir spot welds’, Sci. Technol. Weld. Join., 2010, 15, (1), 81–86.
21.
YinYH, IkutaA, NorthTH: ‘Microstructural features and mechanical properties of AM60 and AZ31 friction stir spot welds’, Mater. Des., 2010, 31, 4764–4776.
22.
FujimotoM, KogaS, AbeN, SatoYS, KokawaH: ‘Microstructural analysis of the stir zone of Al alloy produced by friction stir spot welding’, Q. J. Jpn Weld. Soc., 2007, 25, (4), 553–559.
