Keyhole welding with the plasma arc welding process occurs when the engineered nozzle and the plasma gas flowrate impart the arc pressure and heat distribution necessary for the formation of a keyhole weld pool. Experimental investigations were conducted to determine the influence of nozzle orifice diameter on weld width and weld stability for a range of substrate thicknesses in Ti-6Al-4V. The experimental results are compared with a semianalytical heat flow model. Both the experimental results and the semianalytical model show that the nozzle orifice diameter can significantly influence the top width and penetration for a given parameter set, particularly in relatively thin substrates.
HallET, MarkPA: ‘Experience of plasma process in the aero-industry’, ‘Plasma arc – advanced tool for welding and coating’, Proc. Welding Institute National Seminar; 1975, London.
2.
McLeanW, PinfoldBE: ‘Operational envelopes for plasma keyhole welding’, Proc. 3rd Int. Conf. on ‘Advances in welding processes’, 93–104; 1974, Abington, TWI.
3.
SmartMD, PinfoldBE: ‘Comparison of modulated and unmodulated current plasma-arc welding’, Weld. Met. Fabr., 1971, 39, (9), 332–340.
TsayLW, ChenC, ChengSW: ‘Effect of welding parameters on the working envelopes for plasma arc welding’, Int. J. Mater. Prod. Technol., 1991, 6, (3), 217–226.
6.
NaritaK, TakagiK, KimuraT, MitsuiA: ‘Plasma arc welding of pipelines: a study to optimise welding conditions for horizontal fixed joints of mild steel pipes’, Int. J. Pres. Ves. Pip., 1975, 3, (4), 233–266.
7.
ZhangSB, ZhangYM: ‘Stability of keyhole in plasma arc welding’, Proc. IMechE, Part B: J. Eng. Manuf., 2000, 214B, (B5), 401–405.
8.
BashenkoVV, SosninNA: ‘Optimization of the plasma arc welding process’, Weld. J., 1988, 67, (10), 233–237.
9.
NishiguchiK: ‘Plasma arc welding and cutting’, in ‘Advanced joining technologies’, (ed. NorthT H), 36–47; 1990, Suffolk, Chapman and Hall.
10.
MatsunawaA, OhjiT: ‘Role of surface tension in fusion welding. Part 2: hydrostatic effect’, Trans. JWRI, 1983, 12, (1), 123–130.
11.
ZhangYM, ZhangSB: ‘Observation of the keyhole during plasma arc welding’, Weld. J.1999, 78, (2), 53s–58s.
12.
ShortA: ‘Plasma arc welding for fabricating titanium aero-engine structures’, PhD thesis, University Of Nottingham, Nottingham, UK, 2009.
13.
DavidStan A, DebRoyTarasankar, DuPontJohn N, KosekiSmarttToshihikoHerschel B: ‘Parametric envelopes for keyhole plasma arc welding of a titanium alloy’, Proc. 8th Int. Conf. on ‘Trends in welding research’; 2009, Pine Mountain, GA, ASM.
14.
CastroMBG, Dos SantosJF, QuintinoML: ‘Plasma arc welding of the superalloys Inconel 625 and 718: parameter areas and mechanical properties’, Int. J. Join. Mater., 2003, 15, (1–2), 1–8.
McGillicuddyK: ‘Evaluation of the GTA and plasma welding processes applied to Ti–6Al–4V for aerospace applications’, PhD thesis, Cranfield University, Cranfield, UK, 2002.
17.
ShiganovNV, TregubovGP, OrlovMP: ‘Some of the features of the formation of plasma arc welds in high strength steel’, Weld. Prod., 1972, 19, (1), 27–29.
PinfoldBE, JubbJEM: ‘Plasma arc welding. Part 1–6: welding technology data sheet’, Weld. Met. Fabr., 1974, 41(11)–42(7).
20.
ShawCB: ‘Effect of orifice geometry in plasma-arc welding of Ti–6Al–4V’, Weld. J., 1980, 59, (4), 121–125.
21.
GubenkoVA, MolokanovaTV, NovikovAM: ‘Effects of the high-performance arc current, and the rate of flow of gas, on the heating of nozzles’, Autom. Weld., 1975, 28, (5), 31–33.
22.
DemyantsevichVP, SosninNA: ‘Some ways of increasing the efficiency of the plasma arc’, Weld. Prod., 1974, 21, (4), 26–29.
23.
KimuraT, KomatsuA, YoshiokaS, MiyazakiT: ‘Small diameter nozzle plasma arc as a processing tool’, Rev. Sci. Instrum., 1992, 63, (6), 3384–3388.
24.
SosninNA: ‘Prigogine's theorem and the stability of fusion welding of butt joints without a backing strip’, Weld. Int., 2006, 20, (8), 637–642.
25.
JarvisBL: ‘Keyhole gas tungsten arc welding: a new process variant’, PhD thesis, University of Wollongong, Wollongong, NSW, Australia, 2001.
26.
KwonY, WeckmanDC: ‘Analytical thermal model of conduction mode double sided arc welding’, Sci. Technol. Weld. Join., 2008, 13, (6), 539–549.
27.
NestorOH: ‘Heat intensity and current density distributions at the anode of high current, inert gas arcs’, J. Appl. Phys., 1962, 33, (5), 1638–1648.
28.
DowdenJ, KapadiaP, FennB: ‘Space charge in plasma arc welding and cutting’, J. Phys. D: Appl. Phys., 1993, 26D, 1215–1223.
29.
BemisBL, SettleGS: ‘Ultraviolet imaging of the anode attachment in transferred-arc plasma cutting’, IEEE Trans. Plasma Sci., 1999, 27, (1), 44–45.
30.
NemchinskyVA, SeveranceWS: ‘What we know and what we do not know about plasma arc cutting’, J. Phys. D: Appl. Phys., 2006, 39D, (22), R423–R438.
31.
TeuletP, GirardL, RazafinimananaM, GleizesA, BertrandP, Camy-PeyretF, BaillotE, RichardF: ‘Experimental study of an oxygen plasma cutting torch. Part II: arc-material interaction, energy transfer and anode attachment’, J. Phys. D: Appl. Phys., 2006, 39D, (8), 1557–1573.
32.
FuerschbachPW, KnorovskyGA: ‘A study of melting efficiency in plasma arc and gas tungsten arc welding’, Weld. J., 1991, 70, (11), 287–297.
33.
KouS: ‘Heat transfer in materials processing’, 1996.
34.
KomanduriR, HouZ: ‘Thermal analysis of the arc welding process: part I. General solutions’, Metall. Mater. Trans. B, 2000, 31B, (6), 1353–1370.
35.
GrongO: ‘Metallurgical modelling of welding’; 1994, London, Institute of Materials.
