A study is presented on the influence of the clamping support distance on welding distortion of 6 mm thick gas metal arc welded structural steel T joints. Experiments were performed for two clamping conditions and are compared to simulations based on a previously presented model. It was found that clamping closer to the weld seam reduces angular as well as bending distortion. In order to assess the accuracy of the results, sensitivity analyses were performed on the influence of predeformation and material parameters. It is shown that an initial predeformation has an influence on the final welding distortion. Additionally, it has been found that selection of material properties within the range of variations permitted by the material norms has a strong influence on the predicted distortion. Results were improved using material specific data rather than generic data for the relevant material class. Also the assumed phase volume change plays an important role.
RadajD.: ‘Eigenspannungen und Verzug beim Schweißen – Rechen- und Meßverfahren’; 2002, Düsseldorf, DVS-Verlag.2. K. Masubuchi: ‘Analysis of welded structures’; 1980, New York. Pergamon Press Ltd.
2.
GuanQ., ZhangC. and GuoD.: ‘Dynamic control of welding distortion by moving spot heat sink’, Weld. World, 1994, 33, (4), 308–312.
3.
van der AaE.: ‘Local cooling during welding: prediction and control of residual stresses and buckling distortion’, PhD thesis, TU Delft, Delft, The Netherlands, 2007.
4.
MichalerisP., DantzigJ. and TortorelliD.: ‘Minimization of welding residual stress and distortion in large structures’, Weld. J., 1999, 78, 361–366.
5.
DeoM. and MichalerisP.: ‘Mitigation of welding induced buckling distortion using transient thermal tensioning’, Sci. Technol. Weld. Join., 2003, 8, (1), 49–54.
6.
TsaiC.L., ParkS.C. and ChengW.T.: ‘Welding distortion of a thin-plate panel structure’, Weld. J., 1999, 78, (5), 157–165.
7.
MochizukiM., HayashiM. and HattoriT.: ‘Residual stress distribution depending on welding sequence in multi-pass welded joints with X-shaped groove’, J. Press. Vessel Technol., 2000, 122, 27–32.
8.
RoerenS., SchwenkC., RethmeierM.: Different Approaches to Model Clamping Conditions within a Welding Simulation, in: (ed. H. Cerjak, H. K. D. H. Bhadeshia, E. Kozeschnik): Mathematical Modelling of Weld Phenomena Volume 8, Verlag der Technischen Universität Graz, 2007, pp. 1093–1106.
9.
SchenkT., RichardsonI. M., KraskaM. and OhnimusS.: ‘The influence of clamping on the distortion of welded S355 T-joints’, Sci. Technol. Join. Weld., 2009, 14, (4), 669–675.
10.
SchenkT., RichardsonI. M., KraskaM. and OhnimusS.: ‘A study on the influence of clamping on welding distortion’, Comput. Mater. Sci., 2009, 45, 999–1005.
11.
LiuC. and ZhangJ. X.: ‘Numerical simulation of transient welding angular distortion with external restraints’, Sci. Technol. Weld. Join., 2009, 14, (1), 26–31.
12.
JungG.: ‘Plasticity-based distortion analysis for fillet welded thin plate T-joints’, PhD thesis, Ohio State University, Columbus, OH, USA, 2003.
13.
MandalN. R.: ‘Welding and distortion control’; 2004, New Delhi, Narosa Publishing House.
14.
QiaoG., GuoL. D., LiC. Q. and LeggattR. H.: Low Stress Non-Distortion (LSND), Welding-a New Technique for Thin Materials- Welding in the World (UK), 33(3), p.160–167, 1994.
15.
SagalevichV. M.: ‘Methods for removal of welding distortions and stresses’; 1974, Moscow, Mashinostroenye.
16.
SchenkT., RichardsonI. M., KraskaM. and OhnimusS.: ‘A non-isothermal thermomechanical–metallurgical model and its application to welding simulations’, Sci. Technol. Join. Weld., 2009, 14, (2), 152–160.
17.
ABAQUS user's manual, version 6.8, Hibbit, Karlsson and Sorensen Inc., Providence, RI, USA.
18.
PeilU. and WichersM.: ‘Schweißen unter Betriebsbeanspruchung – Werkstoffkennwerte für einen S355 J2G3 unter temperaturen bis 1200°C’, Stahlbau, 2004, 73, (6), 400–416.
19.
ChabocheJ.-L.: ‘Constitutive equations for cyclic plasticity and cyclic viscoplasticity’, Int. J. Plast., 1989, 5, 247–254.
20.
LeBlondJ. and DevauxJ.: ‘Mathematical modelling of transformation plasticity in steels. I: Case of ideal-plastic phases’, Int. J. Plast., 1989, 5, 551–572.
21.
KoistinenD. and MarburgerE.: ‘A general equation describing the extent of the austenite–martensite transformation in pure iron–carbon alloys and plain carbon steels’, Acta Metall., 1959, 7, 59–60.
22.
DaviesR. G.: ‘Influence of martensite composition and content on the properties of dual phase steels’, Metall. Trans. A, 1978, 9A, 671–679.
23.
GoldakJ.: ‘A finite element model for welding heat sources’, Metall. Trans. B, 1984, 15B, 299–305.
24.
SimoJ.C. and RifaiM. S.: ‘A class of assumed strain methods and the method of incompatible modes’, Int. J. Numer. Methods Eng., 1990, 29, 1595–1638.
25.
LindgrenL.: ‘Finite element modeling and simulation of welding: Part I’, Therm. Stress., 2001, 24, 141–192.
26.
SchumannH.: ‘Metallographie’; 1991, Leipzig, Verlag für Grundstoffindustrie.
27.
DeanD. and HidekazuM.: ‘Prediction of welding residual stress in multi-pass butt-welded modified 9Cr-1Mo steel pipe considering phase transformation effects’, Comput. Mater. Sci., 2006, 37, 209–216.
28.
ChenQ., PawelskiO. and KasparR.: ‘Contribution to the deformation characteristics of dual-phase steels’, Z. Metallkd, 1985, 76, 348–352.
29.
TaljatB., RadhakrishnanB. and ZachariaZ.: ‘Numerical analysis of GTA welding process with emphasis on post-solidification phase transformation effects on residual stresses’, Mater. Sci. Eng. A, 1998, A246, 45–54.
