One of the most relevant aspects of friction stir welding is the possibility to weld different materials. In the present paper, the authors present an improved continuum finite element model for the simulation of friction stir welding processes aimed to obtain T joints, made of a stringer in AA7175-T73511 and of a skin in AA2024-T4. The model, taking into account the thermomechanical behaviours of the two different materials, is utilised to study the occurring material flow and residual stress state. Numerical results are compared with experimental observations: the model is able to predict the material flow, obtaining important information on the joint failure mode.
ZinkW.: ‘Laser beam welding for aircraft structures’, Proc. Aeromat 2000; 2000, Bremen, Daimler Chrysler Aerospace Airbus.
2.
GibsonA. and SterlingS.: ‘A design and test programme involving welded sheet-stringer compression panels’, Proc. ICAS 1998, Melbourne, Australia, August 1998, ICAS, ICAS-98-7-7–4.
3.
FinchD. M. and BurekinF. M.: ‘Effect of welding residual stresses on significance of defects in various types of welded joints’, Eng. Fract. Mech., 41, (5), 721–735.
4.
SticklerP. B. and RamuluM.: ‘Investigation of mechanical behaviour of transverse stitched T-joints with PR520 resin in flexure and tension’, Compos. Struct., 52, 307–314.
5.
TengT. L., FungC. P., ChangP. H. and YangW. C.: ‘Analysis of residual stresses and distortions in T-joint fillet welds’, Int. J. Pres. Ves. Pip., 78, 523–538.
6.
MashiriF. R., ZhaoX. L. and GrundyP.: ‘Stress concentration factors and fatigue behaviour of welded thin-walled CHS-SHS T-joints in-plane bending’, Eng. Struct., 26, 1861–1865.
7.
CarpinteriA., BirghentiR., HuthH. and VantadoriS.: ‘Fatigue growth of a surface crack in a welded T-joint’, Int. J. Fatigue, 2005, 27, 59–69.
8.
ShaikhH., KhatakH. S., MahendranN. and SethiV. K.: ‘Failure analysis of a T-joint of AISI type 316L stainless steel’, Eng. Fail. Anal., 2003, 10, 113–118.
9.
PangH. L. and PukasS. R.: ‘Residual stress measurements in a cruciform welded joint using hole drilling and strain gauges’, Strain, 1989, 25, 7–14.
10.
FinchD. M. and BurekinF. M.: ‘Effect ofwelding residual stresses on significance of defects in various types of welded joints’, Eng. Fract. Mech., 1992, 41, (5), 721–735.
11.
MaN. X., UedaY., MurakawaH. and MadeaH.: ‘FEM analysis of 3D welding residual stresses and angular distortion in T-type fillet welds’, Trans. JWRI, 1995, 24, (2), 115–122.
12.
MishraR. S. and MaZ. Y.: ‘Friction stir welding and processing’, Mater. Sci. Eng. R, 2005, R50, 1–78.
13.
NandanR., DebRoyT. and BhadesiaH. K. D. H.: ‘Recent advances in friction-stir welding – process, weldment structure and properties’, Prog. Mater. Sci., 53, 980–1023.
14.
ErbslöhK., Dalle DonneC. and LohwasserD.: ‘Friction stir welding of T-joints’, Mater. Sci. Forum, 2003, 426–432, (4), 2965–2970.
15.
SteelR. J., NelsonT. W., SorensenC. D. and PackerS. M.: ‘Friction stir welding of steel T-joint configurations’, Proc. Int. Offshore and Polar Engineering Conf., Seoul, South Korea, June 2005, ISOPE, 1–5.
16.
FratiniL., BuffaG., MicariF. and ShivpuriR.: ‘On the material flow in FSW of T-joints: influence of geometrical and technological parameters’, Int. J. Adv. Manuf. Technol., 2009, 44, 570–578.
17.
GuerraM., SchmidtC., McClureL. C., MurrL. E. and NunesA. C.: ‘Flow patterns during friction stir welding’, Mater. Charact, 2002, 49, 95–101.
18.
FratiniL., BuffaG., PalmeriD., HuaJ. and ShivpuriR.: ‘Material flow in FSW of AA7075-T6 butt joints: numerical simulations and experimental verifications’, Sci. Technol. Weld. Join., 2006, 11, (4), 412–421.
19.
SongM. and KovacevicR.: ‘Thermal modeling of friction stir welding in a moving coordinate system and its validation’, Int. J. Mach. Tools Manuf., 2003, 43, 605–615.
20.
DengX. and XuS.: ‘Solid mechanics simulation of friction stir welding process’, Trans. NAMRI/SME, 2001, 29, 631–638.
21.
ZadpoorA. A., SinkeJ. and BenedictusR.: ‘Finite element modeling and failure prediction of friction stir welded blanks’, Mater. Des., 2009, 30, (5), 1423–1434.
22.
BuffaG., HuaJ., ShivpuriR. and FratiniL.: ‘A continuum based FEM model for friction stir welding – model development’, Mater. Sci. Eng. A, 2006, A419, (1–2), 389–396.
23.
BuffaG., HuaJ., ShivpuriR. and FratiniL.: ‘Design of the friction stir welding tool using the continuum based FEM model’, Mater. Sci. Eng. A, 2006, A419, (1–2), 381–388.
24.
FratiniL. and BuffaG.: ‘Metallurgical phenomena modelling in friction stir welding of aluminium alloys: analytical vs. neural network based approaches’, ASME J. Eng. Mater. Technol., 2008, 130, (3), 31001.
25.
BuffaG., FratiniL. and ShivpuriR.: ‘Finite element studies on friction stir welding processes of tailored blanks’, Comput. Struct., 2008, 86, (1–2), 181–189.
26.
GerlichA., SuP., YamamotoM. and NorthT. H.: ‘Material flow and intermixing during dissimilar friction stir welding’, Sci. Technol. Weld. Join., 2008, 13, (3), 254–264.
27.
LiyanageT., KilbourneJ., GerlichA. P. and NorthT. H.: ‘Joint formation in dissimilar Al alloy/steel and Mg alloy/steel friction stir spot welds’, Sci. Technol. Weld. Join., 2009, 14, (6), 500–508.
28.
DEFORM 3D V.6–1 user's manual, STC, Columbus, OH, USA.
29.
PrasedY. V. R. K. and SasidharaS. (eds.): ‘Hot working guide – a compendium processing maps’; 1997, Materials Park, OH, ASM International.
30.
BuffaG., FratiniL. and MicariF.: Patent no. RM2009A000144, Universita degli Studi di Palermo, Palermo, Italy.
31.
LiT., ShiQ.-Y., LiH.-K., WangW. and CaiZ.-P.: ‘Residual stresses of friction stir welded 2024-T4 joints’. Mater. Sci. Forum, 2008, 580–582, 263–266.
