Low transformation temperature welding (LTTW) wire has been found to improve the fatigue strength in welded joints. In the present study, the temperature dependence of the mechanical properties in a dual phase microstructure of austenite and martensite was estimated using the properties of full austenite and full martensite in numerical analyses. A welding method effective for residual stress reduction and fatigue strength improvement was shown by applying a calculation method under transformation superplasticity and transformation induced plasticity in high strength steel welded joints. With this method, the influence of the welding pass sequence on the residual stress distribution and fatigue strength was examined in a boxing fillet welded joint using LTTW. The transformation tensile residual stress in the weld toe was decreased by sectioned welding, and the fatigue limit by sectioned welding with LTTW improved in comparison with the fatigue limit of a joint welded with conventional wire in the same process.
Payares-AsprinoM. C., KatsumotoH. and LiuS.: ‘Effect of martensite start and finish temperature on residual stress development in structural steel welds’, Weld. J., 2003, 5, (8), 279–289.
2.
JonesW. K. C. and AlberryP. J.: ‘A model for stress accumulation in steels during welding’, Met. Technol., 1977, 11, 557–566.
3.
WithersP. J. and BhadeshiaH. K. D. H.: ‘Residual stress part 1 – measurement techniques’, Mater. Sci. Technol., 2001, 17, 355–365.
4.
WithersP. J. and BhadeshiaH. K. D. H.: ‘Residual stress part 2 – nature and origins’, Mater. Sci. Technol., 2001, 17, 366–375.
5.
EckerlidJ., NilssonT. and KarlssonL.: ‘Fatigue properties of longitudinal attachments welded using low transformation temperature filler’, Sci. Technol. Weld. Join., 2003, 8, 353–359.
6.
LixingH., DongpoW., WenxianW. and TainjinY.: ‘Ultrasonic peening and low transformation temperature electrodes used for improving the fatigue strength of welded joints’, Weld. World, 2004, 48, 34–39.
7.
FrancisJ. A., StoneH. J., KunduS., RoggeR. B., BhadeshiaH. K. D. H., WithersP. J. and KarlssonL.: ‘Transformation temperatures and welding residual stresses in ferritic steels’, Proc. PVP2007, San Antonio, TX, USA, July 2007, ASME, 1–8.
8.
DarcisPh. P., KatsumotoH., Payares-AsprinoM. C., LiuS. and SiewertT. A.: ‘Cruciform fillet welded joint fatigue strength improvements by weld metal phase transformations’, Fatig. Fract. Eng. Mater. Struct., 2008, 31, 125–136.
9.
Payares-AsprinoM. C., KatsumotoH. and LiuS.: ‘Effect of martensite start and finish temperature on residual stress development in structural steel welds’, Weld. J. Res. Suppl., 2008, 87, 279s–289s.
10.
DaiH., FrancisJ. A., StoneH. J., BhadeshiaH. K. D. H. and WithersP. J.: ‘Characterising phase transformations and their effects on ferritic weld residual stresses with X-rays and neutrons’, Metall. Mater. Trans. A, 2008, 39A, 3070–3078.
11.
BhadeshiaH. K. D. H.: ‘Possible effects of stress on steel weld microstructures’, in ‘Mathematical modelling of weld phenomena’, (ed. H. Cerjak and H. K. D. H. Bhadeshia), Vol. II, 71–118; 1995, London, Institute of Materials.
12.
YoshihisaE. and RamanS. G. S.: ‘Thermomechanical and isothermal fatigue behavior of type 316 stainless steel base metal, weld, and joint’, Sci. Technol. Weld. Join., 2000, 5, (3), 174–182.
13.
YangY.-S., SonK.-J., ChoS.-K., HongS.-G., KimS.-K. and MoK.-H.: ‘Effect of residual stress on fatigue strength of resistance spot weldment’, Sci. Technol. Weld. Join., 2001, 6, (6), 397–401.
14.
ChapetiM. D., BelmonteJ., TagawaT. and MiyataT.: ‘Integrated fracture mechanics approach to analyse fatigue behavior of welded joints’, Sci. Technol. Weld. Join., 2004, 9, (5), 430–438.
15.
EckerlidJ., NilssonT. and KarlssonL.: ‘Fatigue properties of longitudinal attachments welded using low transformation temperature filler’, Sci. Technol. Weld. Join., 2003, 8, (5), 353–359.
16.
ZenitaniS., HayakawaN.YamamotoJ., HiraokaK., MorikageY., KuboT., YasudaK. and AmanoK.: ‘Development of new low transformation temperature welding consumable to prevent cold cracking in high strength steel welds’, Sci. Technol. Weld. Join., 2007, 12, (6), 516–522.
17.
OhtaA., WatanabeO., MaedaY. and SuzukiN.: ‘Doubled fatigue strength of box welds by using low transformation temperature welding material’, J. Construct. Steel, 1999, 7, 173–180.
18.
OhtaA., WatanabeO., MatsuokaK., ShigaC., NishijimaS., MaedaY., SuzukiN. and KuboT.: ‘Fatigue strength improvement of box welded joints by using low transformation temperature welding material’, Q. J. JWS, 2000, 18, (1), 141–145.
19.
OhtaA., MaedaY. and SuzukiN.: ‘Fatigue strength improvement of butt welded pipe by using low-temperature transformation welding material’, Prep. Natl Meet. JWS, 2000, 66, 120–121.
20.
OhtaA., SuzukiN. and MaedaY.: ‘Fatigue strength improvement of single bevel groove longitudinal welded joints by low transformation temperature welding material’, Prep. Natl Meet. JWS, 2001, 68, 140–141.
21.
SuzukiN., OhtaA., MaedaY. and MachidaF.: ‘Fatigue strength improvement by additional welding using low transformation temperature welding wire’, Prep. NatlMeet. JWS, 2001, 68, 142–143.
22.
OhtaA., WatanabeO., MatsuokaK., MaedaY., SuzukiN. and KuboT.: ‘Fatigue strength improvement of box welds by using low transformation temperature welding material-tripled fatigue strength by postweld heat treatment’, Q. J. JWS, 2001, 19, (2), 373–376.
23.
SuzukiN., OhtaA. and MaedaY.: ‘Repair of fatigue cracks initiated around box welds by using low-transformation temperature welding material’, Q. J. JWS, 2003, 21, (1), 62–67.
24.
OhtaA., WatanabeO., MatsuokaK., MaedaY. and KuboT.: ‘Fatigue strength improvement of box welds by low transformation temperature welding wire and PWHT’, Weld. World, 2000, 44, (3), 19–23.
25.
MuramatsuY., KurodaS. and YamamotoJ.: ‘Application of laser speckle strain measurement on welding with several kind of filler materials’, Prep. Natl Meet. JWS, 2003, 73, 338–339.
26.
MuramatsuY., KurodaS. and YamamotoJ.: ‘Detection of phasetransformation during welding by using ESPI system’, Prep. Natl Meet. JWS, 2003, 73, 340–341.
27.
MuramatsuY., KurodaS., YamamotoJ. and You-ChulK.: ‘Detection of phase-transformation during welding procedure – application of the laser speckle method to strain measurement in the welding process (report 6)’, Q. J. JWS, 2004, 22, (1), 101–106.
28.
MuramatsuY., KurodaS., YamamotoJ. and You-ChulK.: ‘Low transformation-temperature materials and welding residual stress-application of the laser speckle method to strain measurement in the welding process (report 7)’, Q. J. JWS, 2004, 22, (1), 107–116.
29.
MochizukiM., MikamiH., YamazakiK. and ToyodaM.: ‘Study on residual stress reduction by using phase transformation phenomena in welding material’, J. JWS, 2008, 26, 145–151.
30.
YamamotoJ., MeguroS., MuramatsuY., HayakawaN. and HiraokaK.: ‘Analysis of residual stress reduction by using Low transformation-temperature materials', Q. J. JWS, 2007, 25, 560–568.
31.
AnamiK. and MikiC.: ‘Fatigue strength improvement by additional welding with low temperature transformation welding materials’, Proc. 5th Workshop on ‘The ultra-steel’, Tsukuba, Japan, January 2001, National Research Institute for Metal, 240–241.
32.
OhtaA., WatanabeO., MatsuokaK., ShigaT., NishijimaS., MaedaY., SuzukiN. and KuboT.: ‘Fatigue strength improvement by using newly developed low transformation temperature welding material', Weld. World, 1993, 43, 38–42.
33.
MatsuokaK., TakahashiI., YoshiiT., LidakaH. and FujiiE.: ‘Effect of plate thickness and heat input on fatigue strength of non-load-carrying fillet welded joints’, IIW XIII-1407-91, IIW, Villepinte, France.
34.
MatsuokaK., TakahashiI., YoshiiT, LidakaH. and FujiiE.: ‘Influence of residual stress on fatigue strength of non-load-carrying fillet welded joints’, Trans. Jpn Weld. Soc., 1993, 24, 70–77.
35.
MochizukiM., MatsushitaS., MorikageY., KuboT. and ToyodaM.: ‘Study on residual stress reduction by using phase transformation phenomena in welding material – studies on numerical simulation of temperature, microstructure, and thermal stress histories durig welding process and their application to welded structure (report 2)’, J. JWS, 2005, 23, 112–121.
36.
NishiyamaZ.: ‘Martensite transformation’, 195–202; 1971, Tokyo, Maruzen.
