Abstract
Conventional transformation induced plasticity (TRIP) steels have high Si levels, which makes it difficult to coat them satisfactorily by hot dip galvanising. As a consequence, new low Si TRIP steels in which Al or P substitutes for the Si are being examined. The compositions, processing, and properties of these new steels are discussed and compared with those of dual phase steels at the same strength level. It is shown that although the presence of retained austenite always gives some benefit to ductility, it is very difficult to produce hot dipped galvanised TRIP steels with very high (> 30%) elongations by a commercial processing route. In contrast, dual phase steels, although having worse properties, still give relatively good formability and can at present be more readily coated.
Get full access to this article
View all access options for this article.
References
1.
`Ultralight steel autobody', ULSAB Final Report, American Iron and Steel Institute, New York, USA
, 1998 .
2.
‘Hot dip galvanising of TRIP and other inter-critically annealed steel sheets’, ILZRO Research Plan ZCO- 33, International Lead Zinc Research Organization, New Research Triangle Park, NC, USA, 1998.
3.
HELLER
T.
ENGL
B.
ERHARDT
B.
ESDOHR
J.
: ISS MWSP Conf. Proc ., 1998 , 36 , 25 –34 .
4.
PICHLER
A.
STIASZNY
P.
POTZINGER
R.
TIKAL
R.
WERNER
E.
: ISS MWSP Conf. Proc . , 1998 , 36 , 259 –274 .
5.
KOJIMA
N.
FUKUI
K.
MIZUI
N.
: ISS MWSP Conf. Proc . , 1998 , 36 , 17 –24 .
6.
ITAMI
A.
TAKAHASHI
M.
SHIODA
K.
: Proc. Symp. on ‘High strength steels for automotives’, Baltimore, MD, USA, October 1994, ISS, 245-253.
7.
MIZUI
N.
KUKUI
F.
KOJIMA
N.
YAMATO
M.
KAWAGUCHI
Y.
OKAMOTO
A.
NAKAZAMA
Y.
: SAE paper 970156, Society of Automotive Engineers, Warrendale, PA, USA, 1997 , 39 -44 .
8.
SUGIMOTO
K.
SHIMIZU
Y.
SAKAGUCHI
J.
: ISS MWSP Conf. Proc . , 1998 , 36 , 275 –281 .
9.
OJIMA
Y.
SHIROI
Y.
TANIGUCHI
Y.
KATO
K.
: ‘Application to body parts of high strength steel sheet containing large volume fractions of retained y’, SAE paper 980954, Society of Automotive Engineers, Warrendale, PA, USA, 1998, 39 -48.
10.
MIURA
K.
TAKAGI
S.
FURUKIMA
O.
OBORA
T.
TANIMURA
S.
: ‘Dynamic deformation behaviour of steel sheets for auto-mobiles’, SAE paper 960019, Society of Automotive Engineers, Warrendale, PA, USA, 1996, 1 -5.
11.
EBERLE
K.
Ph.
HARLET,
P. CANTINIEAUX
VANDE POPULI-ERE
M.
ISS MWSP Conf. Proc . , 1998 , 36 , 251 –257 .
12.
RASHID
M. S.
: in ‘Dual phase and cold pressing vanadium steels in the automobile industry’ , 32 –42 ; 1978 , Berlin , Vanitec .
13.
HEISTERKAMP
F.
STUART
H.
: Proc. Int. Symp. on ‘Tantalum and niobium’, Goslar, Germany, September 1995, Tantalum—Niobium International Study Centre, 97-111.
14.
RIGSBEE
J. M.
AREND
P. J. VANDER
: in ‘Structure and properties of dual phase steels’, (ed.
Kot
R. A.
Morris
J. W.
, 56 -86; 1979 , New York, AIME.
15.
MESSIEN
P.
HERMAN
J. C.
GREDAY
T.
: in ‘Fundamentals of dual phase steels’, (ed.
Kot
R. A.
Bramfitt
B. L.
, 161 -178; 1981 , Warrendale, PA, TMS-AIME.
16.
OKITA
T.
MISUIJI
H.
INOUE
I.
NAKANO
F.
HASHIMOTO
Y.
: Nippon Kokan Tech. Rep. (Overseas), 1985 , (43 ), 25 -32 .
17.
THOMAS
G.
Koo
J. Y.
: in ‘Structure and properties of dual phase steels’, (ed.
Kot
R. A.
Morris
J. W.
, 183 -201; 1979 , New York, AIME.
18.
KIM
N. J.
THOMAS
G.
: Metall. Trans. A , 1981 , 12A , 483 .
19.
STEVEN
W. S.
HAYNES
A. G.
: J. Iron Steel Inst . , 1956 , 183 , 349 .
20.
TOBIYAMA
Y.
OSAWA
K.
HIRATA
M.
: Kawasaki Seitetsu Gihou , 1999 , 31 , 181 .
21.
TANAKA
T.
et al.: in ‘Structure and properties of dual phase steels’ , (ed.
Kot
R. A.
Morris
J. W.
, 221 -241; 1979 , New York, AIME.
22.
KRUPITZER
R. P.
REIS
F.
MINTUS
R. E.
FRANKLIN
J. E.
: Iron Steelmaker , 1981 , 8 , (8 ), 36 –42 .
23.
CRAWLEY
A. F.
SHEHATA
M. T.
: in ‘Metallurgy of continu-ously annealed sheet steel’ , 347 –364 ; 1982 , Warrendale, PA , TMS-AIME .
24.
YOON
J.
JANG
S.
: Proc. 19th ATS Journées Siderurgique, Paris, France, 1998; Rev. Metal!. , to be published.
25.
FUKAGAWA
T.
OKADA
H.
MAEHARA
Y.
: ISIJ Int. , 1994 , 34 , (11 ), 906 –911 .
26.
KREPSKI
R. P.
: in ‘Microstructure and properties of HSLA steels’, (ed.
De Ardo
A. J.
, 497 -505; 1988 , Warrendale, PA, TMS.
27.
KATO
C.
SEKINE
T.
UMINO
S.
YAMASHITA
T.
MOCHIZUKI
K.
MASUDA
M.
: Zairyo to Purosesu (Curr. Adv. Mater. Process .), 1994 , 7 , 1511 .
28.
HIROSE
Y.
TOGAWA
H.
SUMITANI
J.
: Tetsu-to-Hagane (J. Iron Steel Inst. Jpn) , 1982 , 68 , 665 .
29.
ICHIDA
T.
: in ‘International Galvatech '95’ , 359 ; 1995 , Warrendale, PA , ISS .
30.
ISOBE
M.
KATO
C.
MOCHIZUKI
K.
: ISS MWSP Conf. Proc . , 1998 , 35 , 121 –125 .
31.
MAKIMATTILA
S.
: Proc. Int. Conf. on ‘Zinc coated steels’, Madrid, Spain, June 1985, International Lead Zinc Research Organization, E1-5.
32.
ZIEGLER
s. A.
: Iron Steel Eng. , 1986 , 63 , (5 ), 35 .
33.
MACKOWIAK
J.
SHORT
N. R.
: Int. Met. Rev . , 1979 , 24 , 1 –19 .
34.
LANKILA
A.
RANTA-ESKOLA
A.
: in ‘Development in the annealing of sheet steels’, (ed.
Pradham
R.
Gupta
I.
, 151 -158; 1992 , Warrendale, PA, TMS.
35.
MINOTE
T.
TORZUKA
S.
OGAWA
A.
NIIKURA
M.
: ISIJ Int. , 1996 , 36 , (2 ), 201 –207 .
36.
RADTKE
s. F.
: Proc. 1st Int. Conf. on Galvanizing in South Africa: ‘Galvanizing into the next century’, Pretoria, South Africa, November 1986, National Institute for Materials Research of CSIR/South African Hot Dip Galvanizers' Association, 1-15.
37.
MAKIMATTILA
s. J.
SIPPOLA
P.
: in ‘Hot and cold rolled sheet steels’, (ed.
Pradhan
P.
Ludkowski
C.
, 255 -270; 1988 , Warrendale, PA, TMS.
38.
SUZUKI
Y.
OSAWA
K.
KATO
C.
SAKATA
K.
FURUKIMI
O.
mocmzuxi
K.
: Proc. ‘Galvanised steel sheet forum — auto-motive’, London, UK, May 2000, IoM Communications, 57-66.
39.
PICHLER
A.
HRIBERNIG
G.
TRAGL
E.
ANGERER
R.
RADLMAYR
K.
SZINYUR
J.
TRAINT
S.
WERNER
E.
STIASZNY
P.
: ISS MWSP Conf. Proc. , 1999 , 37 , 37 -60 .
40.
SUGIMOTO
K.
MISU
M.
KOBAYASHI
M.
SHIRASAWA
H.
: ISIJ Int. , 1993 , 33 , (7 ), 775 –782 .
41.
ESDOHR
J.
HELLER
T.
: Proc. IBEC ‘97: 'Automotive body materials’, Stuttgart, Germany, 1997, 151-156.
42.
VRIEZE
J.
VORTREFFLICH
W.
BOELEN
B.
ZWETSLOOT
R.
WINTER
L. DE
: ISS MWSP Conf. Proc . , 1999 , 37 , 277 –294 .
43.
VRIEZE
J.
DEKKER
A.
WINTER
H.
ZWETSLOOT
R.
: Proc. ‘Galvanised sheet steel forum — automotive’, London, UK, May 2000, IoM Communications, 17-26.
44.
KOT
R. A.
W
J. W.
(eds.): ‘Structure and properties of dual-phase steels’, 1979, Warrendale, PA, TMS.
45.
DAVENPORT
A. T.
(ed.): ‘Formable HSLA and dual-phase steels’, 1979 , Warrendale, PA, TMS.
46.
KOT
R. A.
BRAMFITT
B. L.
(eds.): `Fundamentals of dual-phase steels', 1981, Warrendale, PA, TMS.
47.
ZACKAY
V. F.
et al.: Trans. ASM , 1967 , 60 , 252 –259 .
48.
MINTZ
B.
WRIGHT
J. C.
: J. Iron Steel. Inst . , 1970 , 208 , 401 –405 .
49.
REISNER
G.
WERNER
E. A.
KERSCBAUMMAYR
P.
PAPST
I.
FISCHER
F. D.
: J. Met . , 1997 , 49 , (9 ), 62 –65 .
50.
HALL
J. A.
ZACKAY
V. F.
PARKER
E. R.
: Trans. ASM , 1969 , 62 ,965 –976 .
51.
MEYER
M. DE
VANDERSCHUEREN
D.
BLAUWE
K. DE
COOMAN
B. B. DE
: ISS MWSP Conf. Proc . , 1999 , 37 , 483 –491 .
52.
MATSUMURA
O.
SAKUMA
Y.
ISHII
Y.
ZHAO
J.
: ISIJ Int. , 1992 , 32 , (10 ), 1110 –1116 .
53.
SUGIMOTO
K.
KOBAYASHI
M.
HASHIMOTO
H.
: Metal!. Trans. B , 1992 , 23A , 3085 –3091 .
54.
SPEICH
G. R.
DEMEREST
V. A.
MILLER
R. L.
: Metal!. Trans. A , 1981 , 12A , 1419 –1428 .
55.
GARCIA
C.
DEARDO
A. J.
: in ‘Structure and properties of dual phase steels’, (ed.
Kot
R. A.
Morris
J. W.
, 40 -61; 1979 , New York, AIME.
56.
DATTA
D. P.
GIKHALE
A. M.
: Metal/. Trans. A , 1981 , 12A , 443 –450 .
57.
NAVARA
E.
BENGTSSON
B.
EASTERLING
K. E.
: Mater. Sci. Technol . , 1986 , 2 , 1196 –1201 .
58.
FURUKAWA
T.
MORIKAWA
H.
TAKECHI
H.
KOYAMA
K.
: in ‘Structure and properties of dual phase steels’, (ed.
Kot
R. A.
Morris
J. W.
, 281 -303; 1979 , New York, AIME.
59.
BHADESHIA
H. K. D. H.
EDMONDS
D. V.
: Met. Sci . , 1983 , 17 , 411 –419 .
60.
BHADESHIA
H. K. D. H.
EDMONDS
D. V.
: Metal/. Trans. A , 1979 , 10A , 895 –907 .
61.
KIM
J. K.
KIM
J. Y.
: SEAISI Q. , Oct. 1995 , 44 –53 .
62.
TAKAHASHI
M.
BHADESHIA
H. D. K. H.
: Mater. Trans., JIM , 1991 , 32 , 689 –696 .
63.
COLDREN
A. P.
ELDIS
G. T.
: J. Met . , March 1980 , 32 , 41 –48 .
64.
CHEN
IL C.
: SEAISI Q. , April 1991 , 44 –49 .
65.
EVANS
P. J.
: Corus Welsh Technology Centre, Port Talbot, UK, personal communication, 1999.
66.
PEARCE
D. C.
: Proc. Seminar on ‘Galvanising of Si containing steels’, Liege, Belgium, 1975, International Lead Zinc Research Organization, 32-47.
67.
SANDELIN
W. R.
: Wire Wire Prod. , 1940 , 15 , (11 ), 721 –749 .
68.
NORUMA
S.
: Zairyo to Purosesu (Curr. Adv. Mater. Process .), 1992 , 5 , 950 .
69.
PLICHTA
M. R.
AARONSON
H.
: Metal!. Trans . , 1974 , 5 , 2611 .
70.
HOUILLER
R. LE
BEGIN
G.
DUBE
A.
: Metal!. Trans . , 1971 , 2 , 2645 .
71.
LESLIE
W. C.
RAUCH
G. C.
: Metal!. Trans. A , 1978 , 9A , 343 .
72.
MAHIEU
J.
CLAESSENS
S.
MEYER
M. DE
COOMAN
B. C. DE
: Proc. `Galvanised steel sheet forum — automotive', London, UK, May 2000, IoM Communications, 185-196.
73.
HERTVELDT
I.
COOMAN
B. C. DE
CLAESSENS
S.
: Proc. Galvatech'98: 4th Int. Conf. on ‘Zinc and zinc alloy coated steel sheet’, Chiba, Japan, Iron and Steel Institute of Japan, 230-235.
74.
GUTTMAN
H.
NIESSEN
P.
: Can. Metal!. Q . , 1972 , 11 , (4 ), 609 –615 .
75.
MESPLONT
C.
WATERSCHOOT
T.
VANDERPUTTE
S.
VANDERSCHUEREN
D.
COOMAN
B. C. DE
: Proc. Conf. TMP2000: Thermomechanical processing of steels', Vol. 2, 495-504; 2000, London, IoM Communications.
76.
RO
K. S.
CHUNG
J. H.
PARK
S. H.
: in ‘High-strength steel sheet for automotive industry’ , 45 –52 ; 1994 , Warrendale, PA , ISS .
77.
SUGIMOTO
K.
USUI
N.
KOBAYASHI
M.
HASHIMOTO
S.
: ISIJ Int. , 1992 , 32 , 1311 –1318 .
78.
SAKUMA
Y.
MATSUMURA
O.
TAKECHI
H.
: Metal/. Trans. A , 1991 , 22A , 489 –498 .
79.
EVANS
P. J.
CRAWFORD
L. K.
JONES
A.
: Ironmaking Steelmaking , 1997 , 24 , 361 –367 .
80.
SUGIMOTO
K.
KOBAYASHI
M.
: in ‘Hot workability of steels and light-alloy composites’, (ed.
McQueen
H. J.
et al.), 503 -514; 1996 , Montreal, Metallurgical Society of CIM.
81.
SUGIMOTO
K.
KOBAYASHI
M.
NAGASAKA
A.
HISHIMOTO
S.
: ISIJ Int. , 1995 , 35 , 1407 –1414 .
82.
SAKUMA
Y.
MATSUMURA
O.
AKISUE
O.
: ISIJ Int. , 1991 , 31 , 1348 –1353 .
83.
IWAYA
T.
TANAKA
T.
MIYAHARA
M.
KORIDA
K.
: Proc. 15th Biennial Cong. of IDDRG Working Group 2 (Material), Toronto, Canada, 1987, 5.
84.
NAGOA
N.
KUNISHIGE
K.
HAMATSU
S.
NUNOKAWA
T.
: Proc. Int. Conf. on ‘Accelerated cooling’, 463-479; 1985, Warrendale, PA, TMS-AIME.
85.
HASHIMOTO
S.
SUDO
M.
HOSODA
T.
SHIBATA
Z.
: Proc. Conf. on ITSLA steels: metallurgy and applications', Beijing, China, 1011-1120; 1985, Materials Park, OH, ASM International.
86.
YOSHITAKE
A.
SAIO
K.
OKITA
T.
: ‘Impact absorbed energy of hat square column in high strength steels’, Paper 960020, Society of Automotive Engineers, Warrendale, PA, USA, 1996, 7 -15.
87.
THIORON
J. L.
HOURMAN
T.
CORNETTE
D.
: ISS MWSP Conf. Proc . , 1998 , 36 , 35 –51 .
88.
PALUSZNY
A.
: ‘State-of-art review of automobile structural crashworthiness’ , 33 –45 ; 1992 , Washington, DC , AISI .
89.
MATSUMURA
O.
SAKURAI
H.
FURUKAWA
F.
: in ‘Hot work-ability of steels and light-alloy composites’, (ed.
McQueen
H. J.
et al), 467 -476 ; 1996 , Montreal, Metallurgical Society of CIM.
90.
MINTZ
B.
NASSAR
A.
ADEJOLU
K.
: Mater. Sci. Technol . , 1997 , 14 , 313 –318 .
91.
MINTZ
B.
: Metall. Mater. Trans. A , 1997 , 28A , 2073 –2084 .
92.
GODET
S.
JACQUES
P.
DELANNEY
F.
: Proc. Conf. TMP2000: `Thermomechanical processing of steels', Vol. 2, 459-465; 2000, London, IoM Communications.
93.
YOKOI
T.
KAWASAKI
K.
TAKAHASHI
M.
KOYAMA,
K.
mizrn
M.
Tech. Notes/Jpn Soc. Automotive Eng. Rev. , 1996 , 17, 210 -212 .
94.
SUGIMOTO
K.
KOBAYASHI
M.
INOUE
K.
MASUDA
S.
: Tetsu-to-Hagané (J. Iron Steel Inst. Jpn) , 1999 , 85 , 856 .
95.
SODERLUND
E.
LARSSON
M.
LINDER
J.
MELANDER
A.
: ‘Fatigue testing of galvanized steel for automotive underbody applications’, Report ZCO-6-1, International Lead Zinc Research Organization, Research Triangle Park, NC, USA/Report IM-1999-529, Swedish Institute for Metals Research, Stockholm, Sweden, 1999.
96.
NILSSON
T.
ENGBERG
G.
TROGAN
H.
: Scand. J. Metall . , 1989 , 18 , 166 –175 .
97.
SAKUMA
Y.
MATLOCK
D. K.
KRAUSS
G.
: Metall. Trans A , 1992 , 23A , 1221 –1232 .
98.
ITAMI
A.
TAKAHASHI
M.
USHIODA
K.
: ISIJ Int. , 1995 , 35 , 1121 –1127 .
99.
HUANG
H.
MATSUMURA
O.
FURUKAWA
T.
: Mater. Sci. Technol . , 1994 , 10 , 621 –626 .
100.
MAMALIS
A. G.
HAIDEMENOPOULOS
G. N.
: J. Mater. Process. Technol . , 1992 , 30 , 211 –230 .
101.
‘High strength warm and cold band’, ECSC Project EUR 18557 (B. Erhardt), CEC, Brussels, Belgium, 1998.
102.
NOMURA
s.
et al.: ‘High tensile strength steel sheet having improved formability’, US Patent 5,470,529, 28 November 1995 (Sumitomo Metal Industries).
103.
MINTZ
B.
: ISIJ Int. , 1999 , 39 , 833 –855 .
104.
CHEN
H. C.
ERA
H.
soomzu
M.
: Metall. Trans. A , 1989 , 20A , 437 –445 .
105.
PICHLER
A.
STIASZNY
R
Mater. Technol. , Steel Res . , 1999 , 70 , (11 ), 459 –464 .
106.
JACQUES
P.
EBERLE
K.
HARLET
Ph.
DELANNY
F.
: ISS MWSP Conf. Proc . , 1998 , 36 , 239 –249 .
107.
XIE
Z. L.
LIU
Y.
HANNINEN
H.
: Acta Metall. Mater . , 1994 , 42 , 4117 –4133 .
108.
JEONG
W. C.
MATLOCK
D. K.
KRAUSS
G.
: Mater. Sci. Eng. A, 1993, A165, 9-18.
109.
MOON
W. J.
KANG
C. Y.
SUNG
J. H.
: J. Korean Inst. Met. Mater . , 1997 , 35 , 297 –304 .
110.
YUE
S.
CHIRO
A. DE
ZAREI-HANZAKI
A.
: J. Met. , Sept. 1997 , 47 , 59 -61 .
111.
MISHA
s.
JHA
B. K.
: Proc. Int. Symp. on ‘Modern low C and ultra-low C steels for cold forming: processing and properties’, (ed.
Bleck
W.
Vol. 1, 109-120; 1998, Aachen, Verlag Mainz.
112.
SUGIMOTO
K.
MISU
M.
KOBAYASHI
M.
SHIRASAWA
H.
: ISIJ Int. , 1993 , 33 , 775 –782 .
113.
RAO
B. V. N.
RASHID
M. S.
: Metallography , 1983 , 16 , 19 –37 .
114.
BRANDT
M. L.
OLSON
G. B.
: Iron Steelmaker, 1993, 20 , (5 ), 55 -60 .
115.
JEONG
W. C.
: in ‘High-strength steel sheet for automotive industry’ , 267 –274 ; 1994 , Warrendale, PA , ISS .
116.
SAMAJDAR
I.
GIRAULT
E.
VERLINDEN
B.
AERNAUT
E.
HUMBEECK
J.
: ISIJ Int. , 1998 , 38 , 998 –1006 .
117.
MIIHKINEN
V. T. T.
EDMONDS
D. V.
: Mater. Sci. Technol . , 1987 , 3 , 422 –431 .
118.
FU
H. T.
YUE
S.
: ISS MWSP Conf. Proc . , 1998 , 36 , 505 –511 .
119.
PARK
S. H.
HAN
H. N.
LEE
J. K.
: ISS MWSP Conf. Proc . , 1998 , 36 , 283 –291 .
120.
PARK
S. H.
CHOO
W. Y.
KO
K. J.
KIM
N. J.
: in ‘Hot workability of steels and light-alloy composites’, (ed.
McQueen
H. J.
et al), 493 -501 ; 1996 , Montreal, Metallurgical Society of CIM.
121.
ZANEI-HANZAKI
A.
YUE
S.
: in ‘Hot workability of steels and light-alloy composites’, (ed.
McQueen
H. J.
et al), 479 -492 ; 1996 , Montreal, Metallurgical Society of CIM.
122.
ONINK
M.
ZIJP
J.
BODIN
A.
: ISS MWSP Conf. Proc . , 1999 , 37 , 61 –66 .
123.
JONES
A.
EVANS
R J.
: in `Low-carbon steels for the 90s', (ed.
Asfahani
R.
Tither
G.
, 1 -15; 1990 , Warrendale, PA, TMS.
124.
JIAO
S.
PENNING
J.
LEYSEN
F.
HOUBAERT
Y.
: ISS MWSP Conf. Proc . , 1999 , 37 , 499 –508 .
125.
WATERSHOOT
J.
COOMAN
B. C. DE
VADERSCHUEREN
D.
STAELENS
B.
: Proc. Conf. TMP2000: Thermomechanical pro-cessing of steels', Vol. 2, 407-417; 2000, London, IoM Communications.
126.
MORRIS
P. F.
WADE
B. A.
BELL
C.
: Proc. Conf. TMP2000: Thermomechanical processing of steels', Vol. 2, 486-494; 2000, London, IoM Communications.
127.
HELLER
T.
ENGL
B.
STICH
G.
THIEMAN
G.
: Proc. Conf. TMP2000: `Thermomechanical processing of steels', Vol. 2, 438-445; 2000, London, IoM Communications.
128.
EBERLE
K.
CANTINEAUX
P.
HARLET
Ph.
Ironmaking Steelmaking , 1999 , 26 , 176 –181 .
129.
RAO
B. V. N.
: US Patent 4,544,422, 1 October 1985.
130.
MINTZ
B.
VIPOND
R.
NASSAR
A.
: Mater. Sci. Technol . , 1993 , 9 , 760 –772 .
131.
FOLEY
R. P.
MATLOCK
D. K.
KRAUSS
G.
: ‘Survey of ongoing approaches to development of high strength steels’, Report ZCO-1-2, International Lead Zinc Research Organization, New Research Triangle Park, NC, USA, 1995.
132.
CLAESSENS
S.
: personal communication , 2000 .
133.
TANG
N. Y.
: Proc. ‘Galvanised steel sheet forum — automotive’, London, UK, May 2000, IoM Communications, 143-151.
134.
GUTTMANN
M.
: Mater. Sci. Forum, 1994, 155-156, 527-548.
135.
STEPHENSON
V.
: Corus RT&D Welsh Technology Centre, Port Talbot, UK, personal communication, 1999.
136.
PELERIN
J.
HOFFMAN
J.
LEROY
V.
: Metallwissenschaft Technik. , 1981 , 35 , 870 –873 .
137.
SEREBRYAKOVA
I. B.
TARASOVA
A. A.
DUBROV
N. F.
: Steel USSR , June 1973 , 3 , 530 –532 .
138.
SCHUMACHER
B.
MEURE
M.
BIELE
B.
MACHEREY
F.
: Proc. ‘Galvanised steel sheet forum — automotive’, London, UK, May 2000, IoM Communications, 163-171.
139.
TOKI
T.
OSHIMA
K.
NAKAMORI
T.
SAITO
Y.
TSUDA
T.
HOBO
Y.
: in ‘The physical metallurgy of zinc coated steels’, (ed.
Marder
A. R.
, 169 -180; 1993 , Warrendale, PA, TMS.
140.
HORI
H.
NAKAMORI
T.
USUKI
N.
TOKI
T.
ARAI
M.
: Proc. Galvatech'98: 4th Int. Conf. on ‘Zinc and zinc alloy coated steel sheet’, Chiba, Japan, Iron and Steel Institute of Japan, 221.
141.
INAKE
J.
NISHIMOTO
A.
NAGAOKA
K.
: Tetsu-to-Hagané (J. Iron Steel Inst. Jpn) , 1982 , 68 , S377 .
142.
ZHANG
L.
BENSINGER
T. R.
: in ‘International Galvatech '95’ , 115 –120 ; 1995 , Warrendale, PA , ISS .
143.
EVANS
P.
: Corus RT&D Welsh Technology Centre, Port Talbot, UK, personal communication, 1999.
144.
BORDIGNON
L.
: ‘Enhanced hot-dip galvanising by controlled oxidation in the annealing furnace’ , CRM , Liege , Belgium , 1999 .
145.
GOODWIN
F. E.
VENKATARAMAN
R.
SIMPSON
T. C.
: Proc. ‘Galvanised sheet steel forum — automotive’, London, UK, May 2000, IOM Communications, 47-56.
146.
Japanese Patent 08-170159,
1996
(Sumitomo Metals).
147.
FLINCHIM
C.
et al.: ‘Method of coating low alloy steels’, US Patent 3,925,579, 9 December 1975 (Armco Steel Corp.).
148.
BEATENS
M.
DILEWUNS
J.
VANDERSCHUEREN
D.
: Proc. Int. Symp. on ‘Modern low C and ultra-low C steels for cold forming: processing and properties’, (ed.
Bleck
W.
579 ; 1998 , Aachen , Verlag Mainz .
149.
STIASZNY
P.
PICHLER
A.
SPINDLER
H.
TRAGL
E.
: Proc. ‘Galvanised sheet steel forum — automotive’, London, UK, May 2000, IOM Communications, 7-16.
150.
MEYER
M. DE
COOMAN
B. C. DE
: Iron Steelmaker , 2000 , 27 , (2 ), 55 –63 .
151.
PRICE
S. E.
PICLINGI
M.
RANDLE
V.
: Proc. 19th ATS Journées Siderurgique, Paris, France, 1998; Rev. Metall. , to be published.
152.
MIYOSHI
Y.
YOSHIDA
K.
AZAMI
T.
KANAMARU
T.
KADO
S.
: Tetsu-to-Hagané (J. Iron Steel Inst. Jpn) , 1980 , 66 , 858 –867 .
153.
MINOR
R. E.
BUTLER
J. F.
DUNBAR
F. C.
: in ‘International Galvatech '95’ , 407 –412 ; 1995 , Warrendale, PA , ISS .
154.
LEE
H. H.
HIAM
D.
: Corrosion , 1989 , 45 , 852 –856 .
155.
MIYOSHI
Y.
OKA
J.
MAEDA
S.
: Trans. Iron Steel Inst. Jpn , 1983 , 23 , 974 .
156.
FRIEDEL
F.
MAID
O.
WARNECKE
w.
: Proc. ‘Galvanised sheet steel forum — automotive’, London, UK, May 2000, IOM Communications, 89-101.
157.
COFFIN
C.
THOMPSON
s. w.
: in ‘International Galvatech '95’ , 121 –130 ; 1995 , Warrendale, PA , ISS .
158.
NISHIMOTO
A.
ICHI
J.
NAKAOKA
K.
: Trans. Iron Steel Inst. Jpn , 1986 , 26 , 807 –813 .
159.
NAKAYAMA
M.
KANEMARU
T.
KISHIDA
K.
: Tetsu-to-Hagane (J. Iron Steel Inst. Jpn) , 1980 , 66 , S1050 .
160.
TAKADA
H.
SUDO
M.
TSUKATANI
I.
TAKAI
D.
HASE
A.
TSUJI
K.
: Tetsu-to-Hagané (J. Iron Steel Inst. Jpn) , 1982 , 68 , 1397 .
161.
LIN
C. S.
MESHIE
M.
in ‘International Galvatech '95’ , 335 –342 ; 1995 , Warrendale, PA , ISS .
162.
KIM
J.-S.
CHUNG
J.H.
: Proc. ‘Galvanised sheet steel forum — automotive’, London, UK, May 2000, IOM Communications, 103-108.
163.
HISAMATSU
Y.
: Proc. Conf. Galvatech '89, 3-12; 1989, Tokyo, Iron and Steel Institute of Japan.
164.
ABE
M.
KANARA
S.
OKUYAMA
T.
: Trans. Iron Steel Inst. Jpn , 1985 , 25 , (1 ), B19 .
165.
HERTVELDT
I.
COOMAN
B. C. DE
DILEWUNS
J.
: ISS MWSP Conf. Proc . , 1998 , 35 , 105 –113 .
166.
ARIA
M.
: Zairyo to Purosesu (Curr. Adv. Mater. Process .), 1992 , 5 , 1645 .
167.
GUTTMANN
M.
LEPRETRE
Y.
AUBRY
A.
ROCH
M. J.
MOREAU
T.
DRILLET
P.
MATAIGNE
J. M.
BAUDIN
H.
: in ‘International Galvatech '95’ , 295 –307 ; 1995 , Warrendale, PA , ISS .
168.
URAI
M.
ARIMURA
M.
SAKAI
H.
: Tetsu-to-Hagane (J. Iron Steel Inst. Jpn) , 1994 , 80 , 545 –550 .
169.
SAITO
M.
UCHIDA
Y.
KITTAKA
T.
HIROSE
Y.
HITMATSU
Y.
: Tetsu-to-Hagane (J. Iron Steel Inst. Jpn) , 1991 , 77 , 89 –96 .
170.
ALLEGRA
L.
HART
R. G.
TOWNSEND
H. E.
: Metall. Trans. A , 1983 , 14A , 401 –411 .
171.
JORDAN
C. E.
MARDER
A. R.
: Metall. Mater. Trans. A , 1997 , 28A , 2683 –2694 .
172.
JORDAN
C. E.
ZUHR
R.
MARDER
A. R.
: Metall. Mater. Trans. A , 1997 , 28A , 2695 –2703 .
173.
MATSUMURA
O.
SAKUMA
Y.
TAKESHI
H.
: Trans. ISIJ , 1987 , 27 , 570 –579 .
174.
MATSUMURA
O.
SAKUMA
Y.
TAKECHI
H.
: Ser. Metall . , 1987 , 21 , 1301 –1306 .
175.
MOULD
P. R.
SKENA
C. C.
: in ‘Formable HSLA and dual phase steels’, (ed.
Davenport
A. D.
, 181 -204; 1979 , New York, AIME.
176.
CRAWLEY
F.
et al.: in ‘Fundamentals of dual phase steels’ , (ed.
Kot
R. A.
Bramfitt
B. L.
, 181 -197; 1981 , New York, AIME.