ManyikaJ. et al.: ‘Manufacturing the future: the next era of global growth and innovation’, McKinsey Global Institute Report, November 2012, accessed from www.nist.gov..
3.
TomlinM. and MeyerJ.: ‘Topology optimization of an additive layer manufactured (ALM) aerospace part’. Proc. 7th Altair CAE Technology Conf., 2011, accessed from http://www.altairhyperworks.com..
4.
DunningP. D., BramptonC. J. and KimH. A.: ‘Simultaneous material and topology optimisation using a level-set method’, Mater. Sci. Technol., 2015, 31, 884–894.
5.
RezayatH., ZhaoW., SirirukA., PenumaduD. and BabuS. S.: ‘Structure–mechanical property relationship in fused deposition modelling’, Mater. Sci. Technol., 2015, 31, 895–903.
6.
MunguiaJ. and DalgarnoK.: ‘Fatigue behaviour of laser sintered Nylon 12 in rotating and reversed bending tests’, Mater. Sci. Technol., 2015, 31, 904–911.
7.
HolshouserC. et al.: ‘Out of bounds additive manufacturing’, Adv. Mater. Process., 2013, 171, 15–17.
8.
BabuS. S.: ‘Introduction to integrated weld modeling’, in ‘ASM Handbook’, Vol. 22B, (ed. FurrerD. U. and SemiatinS. L.); 2010, Materials Park, OH, ASM International.
9.
‘Integrated computational materials engineering: A transformational discipline for improved competitiveness and national security’. National Materials Advisory Board, Washington, DC, 2008, http://www.nap.edu/catalog/12199.html.
10.
GockelJ., FoxJ., BeuthJ. and HafleyR.: ‘Integrated pool and microstructure control for Ti–6Al–4V thin wall additive manufacturing’, Mater. Sci. Technol., 2015, 31, 912–916.
11.
KempenK., ThijsL., Van HumbeeckJ. and KruthJ. -P.: ‘Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation’, Mater. Sci. Technol., 2015, 31, 917–923.
12.
ManvatkarV., DeA. and DebRoyT.: ‘Spatial variation of melt pool geometry, peak temperature and solidification parameter during laser assisted additive manufacturing processes’, Mater. Sci. Technol., 2015, 31, 924–930.
13.
DehoffR. R., KirkaM. M., SamesW. J., BilheuxH., TremsinA. S., LoweL. E. and BabuS. S.: ‘Site-specific control of crystallographic grain orientation through electron beam additive manufacturing’, Mater. Sci. Technol., 2015, 31, 931–938.
14.
DehoffR. R., KirkaM. M., ListF. A.III, UnocicK. A. and SamesW. J.: ‘Crystallographic texture engineering through novel melt strategies via electron beam melting: Inconel 718’, Mater. Sci. Technol., 2015, 31, 939–944.
15.
ZengK., PalD., GongH. J., PatilN. and StuckerB.: ‘Comparison of 3DSIM thermal modelling of selective laser melting using new dynamic meshing method to ANSYS’, Mater. Sci. Technol., 2015, 31, 945–956.
16.
KingW., AndersonA. T., FerenczR. M., HodgeN. E., KamathC. and KhairallahS. A.: ‘Overview of modelling and simulation of metal powder bed fusion processes at Lawrence Livermore National Laboratory’, Mater. Sci. Technol., 2015, 31, 957–968.
17.
VitekJ. M.: ‘The effect of welding conditions on stray grain formation in single crystal welds – theoretical analysis’, Acta Mater, 2005, 53, 53–67.
18.
ReedP. A. S., WuX. D. and SinclairI.: ‘Fatigue crack path predicting in UDIMET 720 nickel-based alloy single crystals’, Metall. Mater. Trans. A, 2000, 31A, 109–123.
19.
AzizM. J.: ‘Model for solute redistribution during rapid solidification’, J. Appl. Phys., 1982, 53, 1158–1168.
20.
AshbyM. F.: ‘Hybrid to fill holes in material property space’, Philos. Mag., 2005, 85, 3235–3257.
21.
Bhat BourellD.: ‘Tribological properties of metal matrix composites coatings produced by electrodeposition of copper’, Mater. Sci. Technol., 2015, 31, 969–974.
