Finishing the surface micro-layer of additively manufactured TiAl alloy using electro-thermal discharge assisted post-processing

Abstract

Selective laser melting (SLM) of titanium–aluminium (TiAl) alloy components has gained significant attention in the modern industrial world. The flexibility of the SLM process in producing complex shapes with minimum utilization of material and energy makes it dominant over other manufacturing techniques. As aerospace and biomedical industries demand complex-shaped TiAl alloy components, part fabrication using SLM becomes the ultimate solution. However, the unacceptable level of surface integrity and anisotropic behavior of SLM components demand post processing operations such as laser polishing, chemical polishing, and conventional polishing methods. In this study, a recently developed polishing method called wire electrical discharge polishing (WEDP) is performed on TiAl alloys for obtaining a smooth and defect-free surface. This study aims to investigate the micro-layer modification occurring to the WEDP-processed surface in detail. The experimental results establish the effectiveness of WEDP method in terms of improved surface integrity. The surface finish (Sa) got enhanced by ~88% after WEDP processing. In addition, the thickness of recast layer formed by WEDP was found to be minimum. Moreover, post-processing of TiAl alloy resulted in better surface morphology specifically at lower settings of peak current. It is noteworthy that the migration of wire material was minimum with zinc-coated brass electrode compared to the normal brass electrode. Hence, coated wire electrodes are recommended for WEDP process. In short, an excellent surface integrity can be achieved using WEDP process through favorable surface modification aided by lower peak current and coated wire electrodes. Furthermore, less electrode wear observed in WEDP process enables the deployment of lower feed rates leading to minimal electrode consumption.

Keywords

SLM surface finish WEDP additive manufacturing

Get full access to this article

View all access options for this article.

References

Ngo

, Kashani

, Imbalzano

, . Additive manufacturing (3D printing): A review of materials, methods, applications and challenges. Composites, Part B 2018; 143: 172–196. https://doi.org/10.1016/j.compositesb.2018.02.012

Liu

and Shin

. Additive manufacturing of Ti6Al4V alloy: A review. Mater Des 2019; 164: 107552. https://doi.org/10.1016/j.matdes.2018.107552

Zhang

, Li

and Bai

. Defect formation mechanisms in selective laser melting: A review. Chin J Mech Eng 2017; 30: 515–527. https://doi.org/10.1007/s10033-017-0121-5

Boban

, Ahmed

, Jithinraj

, . Polishing of additive manufactured metallic components: retrospect on existing methods and future prospects. Int J Adv Manuf Technol 2022; 121: 83–125. https://doi.org/10.1007/s00170-022-09382-y

Marimuthu

, Triantaphyllou

, Antar

, . Laser polishing of selective laser melted components. Int J Mach Tools Manuf 2015; 95: 97–104. https://doi.org/10.1016/j.ijmachtools.2015.05.002

Gora

, Tian

, Cabo

, . Enhancing surface finish of additively manufactured titanium and cobalt chrome elements using laser based finishing. Physics Procedia 2016; 83: 258–263. https://doi.org/10.1016/j.phpro.2016.08.021

, Guan

and Zhou

. Laser polishing of additive manufactured Ti alloys. Opt Lasers Eng 2017; 93: 171–177. https://doi.org/10.1016/j.optlaseng.2017.02.005

Worts

, Jones

and Squier

. Surface structure modification of additively manufactured titanium components via femtosecond laser micromachining. Opt Commun 2019; 430: 352–357. https://doi.org/10.1016/j.optcom.2018.08.055

, Ouyang

, Liu

, . Effects of laser polishing on surface morphology and mechanical properties of additive manufactured TiAl components. J Manuf Processes 2021; 65: 51–59. https://doi.org/10.1016/j.jmapro.2021.03.014

10.

Ermergen

and Taylan

. Review on surface quality improvement of additively manufactured metals by laser polishing. Arab J Sci Eng 2021; 46: 7125–7141. https://doi.org/10.1007/s13369-021-05658-9

11.

Eyzat

, Chemkhi

, Portella

, . Characterization and mechanical properties of As-Built SLM Ti-6Al-4V subjected to surface mechanical post-treatment. Procedia CIRP 2019; 81: 1225–1229. https://doi.org/10.1016/j.procir.2019.03.298

12.

Bagehorn

, Wehr

and Maier

. Application of mechanical surface finishing processes for roughness reduction and fatigue improvement of additively manufactured Ti-6Al-4V parts. Int J Fatigue 2017; 102: 135–142. https://doi.org/10.1016/j.ijfatigue.2017.05.008

13.

Al-Rubaie

, Melotti

, Rabelo

, . Machinability of SLM-produced Ti6Al4V titanium alloy parts. J Manuf Processes 2020; 57: 768–786. https://doi.org/10.1016/j.jmapro.2020.07.035

14.

Milton

, Morandeau

, Chalon

, . Influence of finish machining on the surface integrity of Ti6Al4V produced by selective laser melting. Procedia CIRP 2016; 45: 127–130. https://doi.org/10.1016/j.procir.2016.02.340

15.

Zhang

, Li

, Che

, . Chemical leveling mechanism and oxide film properties of additively manufactured Ti–6Al–4V alloy. J Mater Sci 2019; 54: 13753–13766. https://doi.org/10.1007/s10853-019-03855-4

16.

Bezuidenhout

, Ter Haar

, Becker

, . The effect of HF-HNO3 chemical polishing on the surface roughness and fatigue life of laser powder bed fusion produced Ti6Al4V. Mater Today Commun 2020; 25: 101396. https://doi.org/10.1016/j.mtcomm.2020.101396

17.

Jain

, Corliss

, Tai

, . Electrochemical polishing of selective laser melted Inconel 718. Procedia Manuf 2019; 34: 239–246. https://doi.org/10.1016/j.promfg.2019.06.145

18.

Zhang

, Liao

, Wang

, . Development of a novel chemical mechanical polishing slurry and its polishing mechanisms on a nickel alloy. Appl Surf Sci 2020; 506: 144670. https://doi.org/10.1016/j.apsusc.2019.144670

19.

Boban

, Ahmed

and Assam

. Effect of recirculation zone on debris evacuation during EDM deep hole drilling. Procedia CIRP 2021; 102: 393–398. https://doi.org/10.1016/j.procir.2021.09.067

20.

Ahmed

, Boban

and Rahman

. Novel EDM deep hole drilling strategy using tubular electrode with orifice. CIRP Ann 2021; 70: 151–154. https://doi.org/10.1016/j.cirp.2021.04.004

21.

Boban

, Ahmed

, Rahman

, . Wire electrical discharge polishing of additive manufactured metallic components. Procedia CIRP 2020; 87: 321–326. https://doi.org/10.1016/j.procir.2020.02.023

22.

Boban

and Ahmed

. Improving the surface integrity and mechanical properties of additive manufactured stainless steel components by wire electrical discharge polishing. J Mater Process Technol 2021; 291: 117013. https://doi.org/10.1016/j.jmatprotec.2020.117013

23.

Boban

and Ahmed

. Electric discharge assisted post-processing performance of high strength-to-weight ratio alloys fabricated using metal additive manufacturing. CIRP J Manuf Sci Technol 2022; 39: 159–174. https://doi.org/10.1016/j.cirpj.2022.08.002

24.

Jithinraj

, Ahmed

and Boban

. Improving the surface integrity of additively manufactured curved and inclined metallic surfaces using thermo-electric energy assisted polishing. Surf Coat Technol 2022; 446: 128803. https://doi.org/10.1016/j.surfcoat.2022.128803

25.

Han

, Salvatore

, Rech

, . Effect of abrasive flow machining (AFM) finish of selective laser melting (SLM) internal channels on fatigue performance. J Manuf Processes 2020; 59: 248–257. https://doi.org/10.1016/j.jmapro.2020.09.065

26.

Vilardell

, Krakhmalev

, Fredriksson

, . Influence of surface topography on fatigue behavior of Ti6Al4V alloy by laser powder bed fusion. Procedia CIRP 2018; 74: 49–52. https://doi.org/10.1016/j.procir.2018.08.028

27.

Abhilash

and Chakradhar

Image processing algorithm for detection, quantification and classification of microdefects in wire electric discharge machined precision finish cut surfaces. J Micromanuf 2021; 5(2): 25165984211015410. https://doi.org/10.1177/25165984211015410

28.

Abhilash

and Chakradhar

Failure detection and control for wire EDM process using multiple sensors. CIRP J Manuf Sci Technol 2021; 33: 315–326. https://doi.org/10.1016/j.cirpj.2021.04.009

29.

Abhilash

and Chakradhar

Wire EDM failure prediction and process control based on sensor fusion and pulse train analysis. Int J Adv Manuf Technol 2022; 118: 1453–1467. https://doi.org/10.1007/s00170-021-07974-8

30.

Ahmed

, Tanjilul

, Rahman

, . Ultrafast drilling of Inconel 718 using hybrid EDM with different electrode materials. Int J Adv Manuf Technol 2020; 106: 2281–2294. https://doi.org/10.1007/s00170-019-04769-w

31.

Ahmed

, Dhakar

, Kaul

, . Hardfacing of AISI304 steel: fabrication of oxide-boride-nitride ceramic matrix composite layer by laser-assisted high temperature chemical reaction. Transactions of the IMF 2017; 95: 207–216. https://doi.org/10.1080/00202967.2017.1330247