The continued expansion of fibre-reinforced plastics (FRPs) into non-specialist markets depends on the creation of high-quality products using cost-effective production techniques. The assembly of complex FRP products requires the drilling of the FRP, however, currently there tends to be substantial damage to the FRP area around the hole. A number of methodologies have been adopted to minimize this drilling-induced damage. There is a strong ambiguity regarding how the operating parameters affect the cutting forces and thus the drilling-induced damage. The present investigation focuses on the geometry of the drill point as a candidate parameter that influences the drilling-induced damage. The experimental results suggest a strong relationship between the geometry of the drill point and the drilling-induced damage.
HochengH.TsaoC. C., ‘The path towards delamination-free drilling of composite materials’J. Mater. Process. Technol.167 (2002): 251–264.
2.
AbraoA. M.FariaP. E.CamposR. J. C.ReisP.DavimJ. P., ‘Drilling of fibre reinforced plastics: a review’J. Mater. Process. Technol.186 (2002): 1–7.
3.
KhashabaU. A., ‘Delamination in drilling GFR-thermoset composites’Compos. Struct.63 (2002): 313–327.
4.
HochengH.PuwH. Y., ‘On drilling characteristics of fibre-reinforced thermoset and thermoplastics’Int. J. Mach. Tool Mf.32 (4) (1992): 583–592.
5.
RamuluM.BransonT.KimD., ‘A study on the drilling of composite and titanium stacks’Compos. Struct.54, (2001): 67–77.
6.
WangX.WangL. J.TaoJ. P., ‘Investigation on thrust in vibration drilling of fibre-reinforced plastics’J. Mater. Process. Technol.148 (2002): 239–244.
7.
DavimJ. P.ReisP., ‘Study of delamination in drilling carbon fibre reinforced plastics (CFRP) using design experiments’Compos. Struct.59 (2002): 481–487.
8.
MurphyC.BvrneG.GilchristM. D., ‘The performance of coated tungsten carbide drills when machining carbon fibre-reinforced epoxy composite materials’Proc. IMechE, Part B: J. Engineering Manufacture216(2) (2002): 143–152.
9.
TsaoC. C.HochengH., ‘Taguchi analysis of delamination associated with various drill bits in drilling of composite material’Int. J. Mach. Tool Mf.44 (2002): 1085–1090.
10.
MillerJ. A., ‘Drilling graphite/epoxy at Lockheed’Am. Machin. Autom. Mfg131 (1981): 70–71.
11.
SinghI.BhatnagarN., ‘Drilling of uni-directional glass fibre-reinforced plastics (UD-GFRP) composite laminates’Int. J. Adv. Mfg Technol.27 (131) (2006): 870–876.
12.
DavimJ. P.ReisP., ‘Drilling carbon fibre reinforced plastics manufactured by autoclave-experimental and statistical study’Mater. Des.24, (2003): 315–324.
13.
DavimJ. P.ReisP.AntonioC. C., ‘Experimental study of drilling glass fibre reinforced plastics (GFRP) manufactured by hand lay-up’Compos. Sci. Technol.64 (2002): 289–297.
14.
AbraoA. M.CamposR. J. C.FariaP. E.DavimJ. P., ‘The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite’Mater. Des.29 (2) (2008): 508–513.
15.
HochengH.TsaoC. C., ‘Effects of special drill bits on drilling-induced delamination of composite materials’Int. J. Mach. Tool Mf.46 (2002): 1403–1416.
16.
HughesJ. I.SharmanA. R. C.RidgwayK., ‘The effect of tool edge preparation on tool life and workpiece surface integrity’Proc. IMechE, Part B: J. Engineering Manufacture218 (2002): 1113–1123.
17.
FernandesM.CookC., ‘Drilling of carbon composites using a one shot drill bit. Part II: empirical modeling of maximum thrust force’Int. J. Mach. Tool Mf.46, (2006): 76–79.
18.
NegarestaniR.SundarM.SheikhM. A.MativengaP.LiL.LiZ. L.ChuP. L.KhinC. C.ZhengH. Y.LimG. C., ‘Numerical simulation of laser machining of carbon-fiber-reinforced composites’Proc. IMechE, Part B: J. Engineering Manufacture224 (2012): 1017–1027 DOI: 10.1243/09544054JEM1662.
19.
El-SonbatyI.KhashabaU. A.MachalyT., ‘Factors affecting the machinability of GFRP/epoxy composites’Compos. Struct.63 (2002): 329–338.
20.
SinghI.BhatnagarN.ViswanathP., ‘Drilling of uni-directional glass fibre reinforced plastics: experimental and finite element study’Mater. Des.29 (2002): 546–553.
