The study investigated the hygrothermal performance and risk of fungal growth in a phenolic foam system with a closed cell structure and a diffusion-open and capillary active lime-cork based insulating plaster, for internal retrofitting purposes. The setup comprised two 40-feet (12.2 m) insulated reefer container with controlled indoor climate, reconfigured with 24 holes (1 × 2 m each) containing solid masonry walls with embedded wooden elements on the interior side. Focus was on the conditions in the masonry/insulation interface and embedded wooden elements, and the performance of the two systems were compared to three diffusion-open insulation systems and one diffusion-tight. The effect of exterior hydrophobisation was also investigated. Relative humidity and temperature were measured in several locations in the test walls over 2½ years, and the risk of fungal growth was evaluated by on-site measurements and the VTT mould-growth model. The findings indicate that internally insulated walls with bare brick exterior surfaces performed poorly with high risk of fungal growth. The effect of exterior hydrophobisation was found to vary with the orientation and the installed insulation system, with a generally positive effect on walls facing south-west but limited effect for north-east. Furthermore, the more diffusion-tight insulation systems were found to perform better in combination with exterior hydrophobisation than the highly diffusion-open systems. The lime-cork insulating plaster showed high relative humidity and risk of moisture-induced problems. The on-site fungal tests showed no growth in the masonry/insulation interface inside the two insulation systems, probably due to high initial pH-value.
CalleKCoupillieCJanssensA, et al. (2020) Implementation of rainwater infiltration measurements in hygrothermal modelling of non-insulated brick cavity walls. Journal of Building Physics43(6): 477–502.
4.
CharolaAE (1995) Water-repellent treatments for building stones: A practical overview. The Journal of Preservation Technology26(2/3): 10–17.
5.
ChristensenGKochAPMøllerEB (2015) Erfaringsblad (31) 151115: Indvendig efterisolering - ældre ydervægge af murværk (Danish). Copenhagen, Denmark. Available at: https://byg-erfa.dk/indvendig-efterisolering-2015 (accessed 2 June 2018)
6.
De MetsTTilmansALoncourX (2017) Hygrothermal assessment of internal insulation systems of brick walls through numerical simulation and full-scale laboratory testing - The 11th Nordic Symposium on Building Physics. In: Energy Procedia, 2017, pp. 753–758. Elsevier B.V. DOI: 10.1016/j.egypro.2017.10.022.
7.
DS/EN ISO 13788 (2013) Hygrothermal Performance of Building Components and Building Elements. Internal Surface Temperature to Avoid Critical Surface Humidity and Interstitial Condensation. Calculation Methods, 2th edn.Charlottenlund, Denmark: Dansk Standard/Danish Standards.
8.
FinkenGRBjarløvSPPeuhkuriRH (2016) Effect of façade impregnation on feasibility of capillary active thermal internal insulation for a historic dormitory - A hygrothermal simulation study. Construction and Building Materials113: 202–214.
9.
GorseCHighfieldD (2009) Refurbishment and Upgrading of Buildings, 2nd edn.New York, USA: Taylor & Francis.
HansenTKBjarløvSPPeuhkuriRH, et al. (2018a) Long term in situ measurements of hygrothermal conditions at critical points in four cases of internally insulated historic solid masonry walls. Energy & Buildings172: 235–248.
12.
HansenTKBjarløvSPPeuhkuriRH, et al. (2018b) Performance of hydrophobized historic solid masonry – Experimental approach. Construction and Building Materials188: 695–708.
13.
HansenTKJensenNFMøllerE, et al. (2020) Monitored conditions in wooden wall plates in relation to wood decaying fungi. In: E3S web conferences volume 172, 2020 12th Nordic Symposium on Building Physics (NSB 2020), Tallinn, Estonia, 2020, p.20004. Elsevier.
14.
HarrestrupMSvendsenS (2016) Internal insulation applied in heritage multi-storey buildings with wooden beams embedded in solid masonry brick façades. Building and Environment99: 59–72.
15.
HäuplPFechnerHPetzoldH (2004) Interior retrofit of masonry wall to reduce energy and eliminate moisture damage: Comparison of modelling and field performance. In: Thermal performance of the exterior envelopes of buildings IX, Clearwater Beach, Florida, US, 2004, pp.1–12. Amer. Soc. Heating, Ref. Air-Conditoning Eng. Inc. Available at: https://web.ornl.gov/sci/buildings/conf-archive/2004%20B9%20papers/096_Haupl.pdf
16.
HäuplPJurkKPetzoldH (2003) Inside thermal insulation for historic facades. Research in Building Physics: 463–469.
17.
HukkaAViitanenHA (1999) A mathematical model of mould growth on wooden material. Wood Science and Technology33(6): 475–485.
JensenNFBjarløvSPOdgaardTR, et al. (2020a) Hygrothermal assessment of diffusion open insulation systems for interior retrofitting of solid masonry walls. Building and Environment182: 107011.
21.
JensenNFBjarløvSPRodeC, et al. (2020b) Hygrothermal assessment of four insulation systems for interior retrofitting of solid masonry walls through calibrated numerical simulations. Building and Environment180: 107031.
22.
JensenNFBjarløvSPRodeC, et al. (2020c) Laboratory based investigation of the materials’ water activity and pH relative to fungal growth in internally insulated solid masonry walls. Submitted to Indoor Air.
23.
JensenNFBjarløvSPRodeC, et al. (2020d) Supplementary Data for ‘Hygrothermal Performance of Six Insulation Systems for Internal Retrofitting Solid Masonry Walls’. Kgs. Lyngby, Denmark: Technical University of Denmark.
24.
JohanssonPGevingSHagentoftC, et al. (2014) Interior insulation retro fi t of a historical brick wall using vacuum insulation panels: Hygrothermal numerical simulations and laboratory investigations. Building and Environment79: 31–45.
25.
KlõšeikoPArumägiEKalameesT (2014) Hygrothermal performance of internally insulated brick wall in cold climate: A case study in a historical school building. Journal of Building Physics38(5): 444–464.
26.
KopeckýPStaněkKBurešM, et al. (2019) Experimental investigations of wooden beam ends in masonry with interior insulation: Measured data in real-scale experimental walls exposed to semi-continental climatic conditions. Journal of Building Physics43(3): 147–170.
27.
KraghJWittchenKB (2014) Development of two Danish building typologies for residential buildings. Energy & Buildings68: 79–86.
MorelliMMøllerEB (2019) Energy savings and risk of mold growth in apartments renovated with internal insulation (Accepted Manuscript). Science and Technology for the Built Environment25: 1199–1211.
32.
MorelliMSvendsenS (2013) Investigation of interior post-insulated masonry walls with wooden beam ends. Journal of Building Physics36(3): 265–273.
NicolaiAGrunewaldJZhangJJ (2007) Recent improvements in HAM simulation tools: Delphin 5 / CHAMPS-BES. In: Proceedings of 12th symposium of building physics, Dresden, Germany, 29–31 March 2007, pp.866–876. Dresden, Germany: Technische Universität Dresden.
39.
NielsenAMøllerEBRasmussenT V, et al. (2012) Use of sensitivity analysis to evaluate hygrothermal conditions in solid brick walls with interior insulation. In: Proceedings of the 5th International Building Physics Conference (IBPC): The role of building physics in resolving carbon reduction challenge and promoting human health in buildings, Kyoto, Japan, 2012, pp.377–384. Kyoto, Japan: Kyoto University.
40.
OdgaardTBjarløvSPRodeC (2018a) Influence of hydrophobation and deliberate thermal bridge on hygrothermal conditions of internally insulated historic solid masonry walls with built-in wood. Energy and Buildings173: 530–546.
41.
OdgaardTBjarløvSPRodeC (2018b) Interior insulation—Characterisation of the historic, solid masonry building segment and analysis of the heat saving potential by 1d, 2d, and 3d simulation. Energy and Buildings162: 1–11.
42.
OdgaardTBjarløvSPRodeC (2018c) Interior insulation – Experimental investigation of hygrothermal conditions and damage evaluation of solid masonry façades in a listed building. Building and Environment129: 1–14.
43.
OjanenTViitanenHPeuhkuriR, et al. (2010) Mold growth modeling of building structures using sensitivity classes of materials. In: Proceedings of thermal performance of the exterior envelopes of whole buildings XI international conference, Clearwater, Florida, USA, 2010. ASHRAE.
44.
PavlíkZČernýR (2009) Hygrothermal performance study of an innovative interior thermal insulation system. Applied Thermal Engineering29: 1941–1946.
45.
ReeslevMMillerM (2000) The MycoMeter-test. A new rapid method for detection and quantification of mold in buildings. Proceedings of Healthy Buildings1: 589–590.
46.
SchefflerGA (2011) Hygric performance of internal insulation with light-weight autoclaved aerated concrete. In: Proceeding of 5th Int. Conf. Autoclaved aerated concrete, Bydgoszcz, Poland, 15–16September2011, pp.323–335. Bydgoszcz, Poland: University of Technology and Life Sciences Press.
47.
SchefflerGGrunewaldJ (2003) Material development and optimisation supported by numerical simulation for a capillary-active inside insulation material. Research in Building Physics: 77–85. Available at: https://www.irbnet.de/daten/iconda/CIB2346.pdf
48.
SouliosVJanEHansenDP, et al. (2020) Hygric behavior of hydrophobized brick and mortar samples. Building and Environment176: 106843.
TomanJVimmrováAČernýR (2009) Long-term on-site assessment of hygrothermal performance of interior thermal insulation system without water vapour barrier. Energy and Buildings41: 51–55.
52.
TommerupHSvendsenS (2006) Energy savings in Danish residential building stock. Energy and Buildings38: 618–626.
53.
UenoKStraubeJVan StraatenR (2013) Field monitoring and simulation of a historic mass masonry building. In: Proceedings of thermal performance of the exterior envelopes of whole buildings XI, Clearwater, Florida, USA, 2013. Available at: https://www.buildingscience.com/file/3732/download?token=qVIIYJUC
54.
VereeckenERoelsS (2014) A comparison of the hygric performance of interior insulation systems: A hot box – cold box experiment. Energy & Buildings80: 37–44.
55.
VereeckenERoelsS (2015) Capillary active interior insulation: Do the advantages really offset potential disadvantages?Materials and Structures48: 3009–3021.
56.
VereeckenERoelsS (2019) Wooden beam ends in combination with interior insulationã: An experimental study on the impact of convective moisture transport. Building and Environment148: 524–534.
57.
VereeckenEVan GelderLJanssenH, et al. (2015) Interior insulation for wall retrofitting – A probabilistic analysis of energy savings and hygrothermal risks. Energy & Buildings89: 231–244.
58.
ViitanenHVinhaJSalminenK, et al. (2010) Moisture and biodeterioration risk of building materials and structures. Journal of Thermal Envelope and Building Science33(3): 201–224.
59.
ViitanenHKrusMOjanenT, et al. (2015) Mold risk classification based on comparative evaluation of two established growth models. Energy Procedia78: 1425–1430.
60.
WegererPNathanaelJBednarT (2015) Measuring the hygrothermal performance of an interior insulation made of woodfibre boards. In: The 6th international building physics conference, IBPC 2015, Energy Procedia, Torino, Italy, 2015, pp.1478–1483. Amsterdam, Holland: Elsevier Procedia.
61.
WittchenKB (2009) SBi 2009:05 Potentielle energibesparelser i det eksisterende byggeri (Danish). Hørsholm, Denmark: Danish Building Research Institute.
62.
WittchenKBKraghJJensenOM (2011) Energy-saving potential – a case study of the Danish building stock. In: Proceeding at eceee 2011 summer study - Energy Efficiency First: The foundation of a low-carbon sociey, 2011, pp.1355–1363. Stockholm, Sweden: European Council for an Energy Efficient Economy.
