Characterization and application of composite resin of natural rubber latex and polystyrene waste as a binder for water-resistant emulsion paint formulation
Restricted accessResearch articleFirst published online November, 2025
Characterization and application of composite resin of natural rubber latex and polystyrene waste as a binder for water-resistant emulsion paint formulation
Sustainable production of efficient and low-cost coating materials from recycled plastic wastes will have a significant impact on economic advancements in paints and coatings, as well as waste management. Polystyrene waste was reduced to a resin, which was further modified by blending with natural rubber latex (NRL). The recycled polystyrene resin (rPS) and NRL formed homogeneous composite resins (rPS-NRL) blends in various ratios, and the changes in some physicochemical properties of the resins were studied. The rPS-NRL blended in different ratios exhibited higher density (0.83–0.92 g/cm3), refractive index (1.401–1.438), viscosity (935–1287 cP), elongation (5–18 %), and melting point (184°C–217.5°C), as well as lower moisture uptake (1.1–0.88 %) and faster drying time (32–19 min), compared to the rPS resin. Changes in functional, structural, and morphological characteristics of the resins were studied using Fourier transformed infrared (FTIR) spectrometer, X-ray diffractometer (XRD), scanning electron microscope (SEM) and thermogravimetric analyzer (TGA-DTA). The results indicated molecular interactions between NRL and the rPS resin, which form the basis for the unique physicochemical properties of the composite resin compared with the pristine rPS and NRL resins. White (CaCO3) pigmented emulsion paint produced using the rPS-NRL composite resin as binder was tested in comparison with paint produced using the conventional polyvinyl acetate (PVA) binder, where the rPS-NRL paint exhibits superior properties, including outstanding resistance to water.
AkinterinwaABensonAAtikuJU, et al.Development, physicochemical characteristics and applications of paint/coatings: a treatise on the basic science and technology. OmniScience A Multi-disciplinary J2021; 11(3): 11–21.
2.
IfijenIHMalikiMOdiachiIJ, et al.Review on solvents based alkyd resins and water borne alkyd resins: impacts of modification on their coating properties. Chem Africa2022; 5(2): 211–225.
3.
IbrahimBHelwaniZWiranataA, et al.Properties of emulsion paints with binders based on natural latex grafting styrene and methyl methacrylate. Appl Sci2022; 12(24): 12802.
4.
StrokovaVVNikulinaMVBaskakovPS, et al.Influence of a hydrophobic emulsion on the surface properties of coatings of water-dispersion acrylic paint. Mater Sci Forum2021; 1040: 165–171.
5.
MotawieAMSherifMHBadrMM, et al.Synthesis and characterization of waterborne epoxy resins for coating application. Aust J Basic Appl Sci2010; 4: 1376–1382.
6.
ZhangJHuangHMaJ, et al.Preparation and properties of corrosion-resistant coatings from waterborne polyurethane modified epoxy emulsion. Front Mater2019; 6: 185.
7.
SinghAPGunasekaranGSuryanarayanaC, et al.Fatty acid based waterborne air drying epoxy ester resin for coating applications. Prog Org Coating2015; 87: 95–105.
8.
HongCZhouXYeY, et al.Synthesis and characterization of UV-curable waterborne Polyurethane–acrylate modified with hydroxyl-terminated polydimethylsiloxane: UV-cured film with excellent water resistance. Prog Org Coating2021; 156: 106251.
9.
IsmailASJawaidMHamidNH, et al.Physical, structural and thermal properties of bio-phenolic/epoxy polymers blends. Mater Today Commun2023; 34: 105455.
10.
TarannumNPoojaKMKhanR. Preparation and applications of hydrophobic multicomponent based redispersible polymer powder: a review. Construct Build Mater2020; 247: 118579.
11.
OsemeahonSANkafamiyaIIMaiteraON, et al.Synthesis and characterization of emulsion paint binder from a copolymer composite of dimethylol urea/polystyrene. J Polym Compos2015; 3(2): 11–21.
12.
KaliveerVRamachandraRKumarP, et al.Recycling and conversion of waste PET bottles into acrylic paints. AIP Conf Proc2020; 2236(1): 040019.
13.
GhosalKNayakC. Recent advances in chemical recycling of polyethylene terephthalate waste into value added products for sustainable coating solutions–hope vs. hype. Mater Adv2022; 3(4): 1974–1992.
14.
OsemeahonSAAkinterinwaAFasinaE, et al.Reduction of polystyrene/polyurethane plastic wastes from the environment into binders for water-resistant emulsion paints. Heliyon2024; 10(6): e27868.
15.
SchwadePVSchneiderGOSantinCK, et al.Development of paint based on residue of expanded polystyrene: polymeric plasticizer evaluation. Macromol Symp2016; 368(1): 8–18.
16.
de Sousa CunhaRMumbachGDMachadoRAF, et al.A comprehensive investigation of waste expanded polystyrene recycling by dissolution technique combined with nanoprecipitation. Environ Nanotechnol Monit Manag2021; 16: 100470.
17.
Gutierrez-VelasquezEIMonteiroSNColoradoHA. Characterization of expanded polystyrene waste as binder and coating material. Case Stud Constr Mater2022; 16: e00804.
18.
OsemeahonSABarminasJTJangAL. Development of Waste Polystyrene as a binder for emulsion paint formulation II: effect of different types of Solvent. J Environ Sci Toxicol Food Technol2013; 5(4): 1–7.
19.
UttaravalliANDindaSGidlaBR, et al.Studies on development of adhesive material from post-consumer (waste) expanded polystyrene: a two-edged sword approach. Process Saf Environ Protect2021; 145: 312–320.
20.
ChaukuraNGwenziWBunhuT, et al.Potential uses and value-added products derived from waste polystyrene in developing countries: a review. Resour Conserv Recycl2016; 107: 157–165.
21.
FotiDVoulgaridouEKarastergiouS, et al.Value-added wood composites made from waste polystyrene as a binder: a review. In: Proceedings of the First International Conference on “Green” Polymer Materials, [Online], 2020, pp. 5–25.
22.
MyintSZakariaMSBAhmedK. Paints based on waste expanded polystyrene. Prog Rubber Plast Recycl Technol2010; 26(1): 21–30.
23.
BellonDZamudioWHTiriaLC, et al.Effect of expanded polystyrene waste in the creation of waterproofing paint. J Phys Conf Ser2019; 1386(1): 012075.
24.
MangalaraSCHVarugheseS. Green recycling approach to obtain nano-and microparticles from expanded polystyrene waste. ACS Sustain Chem Eng2016; 4(11): 6095–6100.
25.
ZhangXHaoHTianR, et al.Quasi-static compression and dynamic crushing behaviors of novel hybrid re-entrant auxetic metamaterials with enhanced energy-absorption. Compos Struct2022; 288: 115399. DOI: 10.1016/j.compstruct.2022.115399.
26.
JiangHXieYZhuR, et al.Construction of polyphosphazene-functionalized Ti3C2TX with high efficient flame retardancy for epoxy and its synergetic mechanisms. Chem Eng J2023; 456: 141049.
27.
JiangYLiuLYanJ, et al.Room-to-low temperature thermo-mechanical behavior and corresponding constitutive model of liquid oxygen compatible epoxy composites. Compos Sci Technol2024; 245: 110357.
28.
HeXWengQGuoR, et al.Elaborate construction of potent antioxidant properties in PBP-Ce(Ш) nanosheets via a one-pot approach for seamless integration of anti-corrosion, wear-resistance, and flame-retardancy. J Mater Sci Technol2024; 201: 197–209.
29.
SekharanRVAbrahamBTThachilET. Utilization of waste expanded polystyrene: blends with silica-filled natural rubber. Mater Des2012; 40: 221–228.
30.
AjithaARThomasS. Introduction: polymer blends, thermodynamics, miscibility, phase separation, and compatibilization. In: Compatibilization of polymer blends. Amsterdam, Netherlands: Elsevier, 2020, pp. 1–29.
31.
SangronizAGonzalezAMartinL, et al.Miscibility and degradation of polymer blends based on biodegradable poly (butylene adipate-co-terephthalate). Polym Degrad Stabil2018; 151: 25–35.
32.
AkinterinwaAOsemeahonSANkafamiyaII, et al.Formulation of emulsion paint from a copolymer composite of dimethylol urea/polystyrene. Chem Mater Res2015; 7(7): 20–26.
33.
Idowu-OyewoleETOsemeahonSADassPM, et al.Synthesis and characterization of an emulsion paint binder from a copolymer composite of trimethylol urea/polyethylene. Int J Mater Sci Eng2016; 4(2): 161–171.
34.
BahruddinBHelwaniZFadhillahI, et al.Opacity and washability properties of emulsion paint with natural rubber latex/polyvinyl acetate blend binder. J Phys Conf Ser2021; 2049(1): 012092.
35.
WichaitaWPromlokDSudjaipraparatN, et al.A concise review on design and control of structured natural rubber latex particles as engineering nanocomposites. Eur Polym J2021; 159: 110740.
36.
WannaphatchaiyongSSuksaereeJWaipribR, et al.Gelatin/gelatinized sago starch biomembranes as a drug delivery system using rubber latex as plasticizer. J Polym Environ2019; 27: 2380–2394.
37.
NuasaenSTangboriboonratP. Optical properties of hollow latex particles as white pigment in paint film. Prog Org Coating2015; 79: 83–89.
38.
StelescuDMAirineiAHomocianuM, et al.Structural characteristics of some high density polyethylene/EPDM blends. Polym Test2013; 32(2): 187–196.
39.
ZhaoPZhouQLiuX, et al.Phase separation in benzoxazine/epoxy resin blending systems. Polym J2013; 45(6): 637–644.
40.
da Cunha SantosAMCáceresCACalixtoLS, et al.In-line optical techniques to characterize the polymer extrusion. Polym Eng Sci2014; 54(2): 386–395.
41.
AkinterinwaAOgwucheSOsameahonSA, et al.Development of a novel and benign emulsion paint binder from epoxidized soybean oil and dimethylol urea blend. Ruhuna J Sci2019; 10(1): 51.
42.
GómezCInciarteHOrozcoLM, et al.Interesterification and blending with Sacha Inchi oil as strategies to improve the drying properties of Castor oil. Prog Org Coating2022; 162: 106572.
43.
FallahiAGuldentopsGTaoM, et al.Review on solid-solid phase change materials for thermal energy storage: molecular structure and thermal properties. Appl Therm Eng2017; 127: 1427–1441.
44.
GodinhoBGamaNBarros-TimmonsA, et al.Recycling of different types of polyurethane foam wastes via acidolysis to produce polyurethane coatings. Sustain Mater Technol2021; 29: e00330.
45.
KhamplodTLoykulnantSKongkaewC, et al.Electron beam radiation grafting of styrene on natural rubber using Taguchi’s design. Polymer2015; 79: 135–145.
46.
WenYWangYZhaoK, et al.The use of natural rubber latex as a renewable and sustainable modifier of asphalt binder. Int J Pavement Eng2017; 18(6): 547–559.
47.
SalamaMHassaboAGEl-SayedAA, et al.Reinforcement of polypropylene composites based on recycled wool or cotton powders. J Nat Fibers2017; 14(6): 823–836.
48.
FicoDRizzoDDe CarolisV, et al.Sustainable polymer composites manufacturing through 3D printing technologies by using recycled polymer and filler. Polymers2022; 14(18): 3756.
49.
WorleeAHomdongNHayeemasaeN. Application of polymer blend based on natural rubber latex and acrylic resin as a binder for wall paints. IOP Conf Ser Mater Sci Eng2020; 773(1): 012032.
50.
VoMLPlankJ. Evaluation of natural rubber latex as film forming additive in cementitious mortar. Construct Build Mater2018; 169: 93–99.
51.
TurkuIKasalaSKärkiT. Characterization of polystyrene wastes as potential extruded feedstock filament for 3D printing. Recycling2018; 3(4): 57.
52.
ChauhanDAgrawalGDeshmukhS, et al.Biofilm formation by Exiguobacterium sp. DR11 and DR14 alter polystyrene surface properties and initiate biodegradation. RSC Adv2018; 8(66): 37590–37599.
53.
MumbachGDBolzanAMachadoRAF. A closed-loop process design for recycling expanded polystyrene waste by dissolution and polymerization. Polymer2020; 209: 122940.
54.
AgrebiFGhorbelNBressonS, et al.Study of nanocomposites based on cellulose nanoparticles and natural rubber latex by ATR/FTIR spectroscopy: the impact of reinforcement. Polym Compos2019; 40(5): 2076–2087.
55.
FangJXuanYLiQ. Preparation of polystyrene spheres in different particle sizes and assembly of the PS colloidal crystals. Sci China Technol Sci2010; 53: 3088–3093.
56.
ChavanVAnandrajJJoshiGM, et al.Structure, morphology and electrical properties of graphene oxide: CuBiS reinforced polystyrene hybrid nanocomposites. J Mater Sci Mater Electron2017; 28: 16415–16425.
57.
NciriNShinTChoN. Towards the use of waste expanded polystyrene as potential modifier for flexible road pavements. Mater Today Proc2020; 24: 763–771.
58.
BarrosNRChagasPAMBorgesFA, et al.Diclofenac potassium transdermal patches using natural rubber latex biomembranes as carrier. J Mater2015; 2015: 1–7.
59.
FaridaEBukitNGintingEM, et al.The effect of carbon black composition in natural rubber compound. Case Stud Therm Eng2019; 16: 100566.
60.
GintingEMBukitNFridaE, et al.Microstructure and thermal properties of natural rubber compound with palm oil boilers ash for nanoparticle filler. Case Stud Therm Eng2020; 17: 100575.
61.
YangXTangHLiY, et al.Synthesis, characterization, and thermal pyrolysis mechanism of high temperature resistant phenolphthalein-based poly (arylene ether nitrile). Polym Degrad Stabil2024; 224: 110754.
62.
ChaudharyAKVijayakumarRP. Studies on biological degradation of polystyrene by pure fungal cultures. Environ Dev Sustain2020; 22: 4495–4508.
MathewAPPackirisamySThomasS. Studies on the thermal stability of natural rubber/polystyrene interpenetrating polymer networks: thermogravimetric analysis. Polym Degrad Stabil2001; 72(3): 423–439.
65.
LiuYHuJ. Investigation of polystyrene-based microspheres from different copolymers and their structural color coatings on wood surface. Coatings2020; 11(1): 14.
66.
LeeDHLiXXChoUR. Comparison on mechanical properties of SSBR composites reinforced by modified carbon black, silica, and starch. Elastom Compos2018; 53(3): 175–180.
67.
ChangMZhangYPeiJ, et al.Low-temperature rheological properties and microscopic characterization of asphalt rubbers containing heterogeneous crumb rubbers. Materials2020; 13(18): 4120.
68.
CirisanoFFerrariM. Superhydrophobicity and durability in recyclable polymers coating. Sustainability2021; 13(15): 8244.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
