The Thermal Conductivity of Isocyanate-Based Rigid Cellular Plastics: A Technique for Predicting the 25 Year Values * * This paper was first published in Cellular Polymers,Vol. 16,No. 2,1997
Restricted accessOtherFirst published online November, 1997
The Thermal Conductivity of Isocyanate-Based Rigid Cellular Plastics: A Technique for Predicting the 25 Year Values * * This paper was first published in Cellular Polymers,Vol. 16,No. 2,1997
This paper reviews the factors determining the thermal conductivity of isocyanate- based rigid cellular plastics. It provides research data obtained from a programme conducted at Salford University, to establish the basis of a method based on an accelerated procedure for the determination of the thermal conductivity of these products which can be assumed to apply, without taking into account production variation, to a product over its 50 year life. The latter is used to correspond to the term “reasonable economic life" used in the EU Construction Products Directive. The data is limited to products principally expanded with HCFC 141b and n-pentane blowing agents but the authors believe, although proof will be necessary, that the method has a good chance to be acceptable for all future products which are expanded principally with a gas which is shown to remain, for the most part, in the cells over its reasonable economic life and for which the gaseous composition of the cell gas is changed only by dilution, to varying degrees, by the ingress of air. In essence the ingress of air is accelerated by ageing the test specimen in air at 70°C for 25 weeks. The paper also discusses the merits of various other procedures claiming to produce "realistic aged thermal conductivity values". Finally it provides evidence that the products made with these new blowing agents have similar thermal conductivities and similar thermal conductivity ageing characteristics to their CFC blown counterparts.
Get full access to this article
View all access options for this article.
References
1.
DohertyD.J., HurdR., and LesterG.R., Chemistry and Industry, 20, (1962),1340
2.
BuistJ.M., DohertyD.J., and HurdR., Progress in Refrigeration Science and Technology, (1965), 271
3.
HardingR.H., & JamesB.F., Modern Plastics, 39(7), (1962),133
4.
KnoxR.E., paper, presented to the Plastics Foam Insulation Conference of SPI, April (1962)
DixonR.R., EdelmanL.E., McLainD.K., J. Cell. Plastics6 (1) (1970),44
18.
NortonF.J., J. Cell. Plastics3(1), (1967), 23
19.
BenfordA.E., paper presented at the International Cellular Plastics conference, New York, September1968
20.
SchmidtW., Kaltetechnik, 20 (12), (1968), 387
21.
HiladoC.J., ProopsW.R., J. Cell. Plastics, 5(5), (1969), 299
22.
SchmidtW., Applied Plastics, 11(4), (1968), 19
23.
BallG.W., HurdR., WalkerM.G., J. Cell. Plastics, 6(2), (1970), 3
24.
BallG.W., HealeyW.G., PartingtonJ.B., European J. Cell. Plastics, 1(1), (1978), 50
25.
BS 4841 Rigid urethane foam for building applications. Part 1 Laminated board for general purposes (1993)
26.
ibid: Part 2 Laminated board for use as a wall and ceiling insulation (1975)
27.
ibid: Part 3 Specification for two types of laminated board (roofboards) with auto-adhesively bonded reinforcing facings for use as roofboard thermal insulation for built-up roofs (1994)
28.
BS 6586 Rigid polyurethane (PUR) foam produced by the press injection method: Part 1 Specification for PUR foam for insulated panels for transport containers and insulated vehicle bodies (1993)
29.
BS 4840 Rigid polyurethane (PUR) foam in slab form: Part 2 Specification for PUR foam for use in refrigerator cabinets, cold rooms and stores (1994)
30.
BS 7456 Code of practice for stabilization and thermal insulation of cavity walls (with masonry inner and outer leaves) by filling with polyurethane (PUR) foam systems (1991)
31.
BS 7457 Specification for polyurethane (PUR) foam systems suitable for stabilization and thermal insulation of cavity walls with masonry concrete inner and outer leaves (1991)
32.
BS 5241 Rigid polyurethane (PUR) and polyisocyanurate (P1R) foam when dispensed or sprayed on a construction site: Part 2 Specification for dispensed foam for thermal insulation for buoyancy applications (1991)
33.
ibid: Part 1 Specification for sprayed foam thermal insulation applied externally (1989)
34.
BS 7021 Thermal insulation of roofs externally by means of sprayed rigid polyurethane (PUR) or polyisocyanurate (PIR) foam (1989)
BallG.W., HaggisG.A., HurdR., WoodJ.F., J. Cell. Plastics.4(7), (1968), 248
42.
Montreal Protocol on substances that deplete the ozone layer
43.
Council Regulation (EC) No. 3093/94 of 15 December 1994 on substances that deplete the ozone layer
44.
BallG.W., Cellular Polymers, (13), (1994), 434
45.
ISO 8301 Thermal insulation - Determination of steady-state thennal resistance and related properties - Heat flow meter method
46.
ISO 8302 Thermal insulation - Determination of steady-state thermal resistance and related properties - Guarded hot plate method
47.
BoetesR., Heat Transfer Reduction in Closed Cell Polyurethane Foams, PhD Thesis Delft University of Technology, (1986)
48.
RohsenowW.M., HartnetJ.P., GanicE.N., Handbook of Heat Transfer Fundamentals, 2nd Edition, McGraw-Hill, New York, (1985)
49.
DuCauze, de NazelleG., Thermal Conductivity Ageing of Rigid Closed Cell Polyurethane Foams, PhD Thesis Delft University of Technology, (1995)
50.
BombergM., Scaling factor in ageing of gas-filled cellular plastics, Proc. 1st Int. Workshop Long Term Thermal Performance of Cellular Plastics, Session B, Huntsville, (1989)
51.
RouxG., TramblayG., VenutiG., Prediction of the long-term insulation value of PUR foams: The ACERMI method, Cellular Polymers, 1990
52.
F.I.W., Untersuchungen an Pentan-getriebenen PUR-Hartschaum- Dammplatten ohne gasdiffusionsdichte metallische Deckschichten, 14.04.1992
53.
F.I.W., Untersuchungen an FCKW-freien Polyurethan (PUR)- Hartschaumplatten ohne gasdiffusionsdichte metallische Deckschichten, 29.05.1992
BiesmansG., de VosR., RosbothamI.D., The use of alternative blowing agents in polyurethane foams - A comparison between experimental and predicted ageing, Polyurethanes World Congress1993, Oct.10-13,1993
56.
Kohonen, Dr. Reijo, Kokko, Erkki, Sievanen, Markku, (Technical Research Centre of Finland), The ageing of polyurethane insulation containing CO2, N2 and O2 with gas diffusion-tight facings, Nov.1990
57.
WalterR., Wendel, St., Calculation model for the prediction of gas diffusion and ageing of CFC-free PUR rigid foam, Reprint from UTECH ’92 Conference
58.
HeiligG., WiedermannR., Pentane blown polyurethane rigid foams for construction, Polyurethanes World Congress1993
59.
Mitteilungen des DIBV 1993 zu DIN 18164 Teil 1, Ausgabe 8.92
60.
PompeoC., Study of the thermal characteristics of polyurethane foams containing a gas other than air (CFC 11, pentane), CSTB- Report ELT/HTO 93-01C sponsored by BING, 1993
61.
PompeoC., Study of the thermal characteristics of polyurethane foams containing a gas other than air (HCFC 141b), CSTB-Report ELT/HTO 94-008C sponsored by BING, 1994
62.
LohmeyerS., MullerG., Bestimmung der porengasmenge und zusammensetzung in polyurethanschaumen, Kaltetechnik- Klimatisierung H. 9, S. 291-294,1970
63.
ISO/DIS 11561.2 Determination of the long-term change in thermal resistance of rigid closed cell cellular plastic thermal insulation by slicing and scaling
64.
CEN/TC88/WG6 Draft European Standard: Thermal insulation products for buildings - Factory made products of rigid polyurethane foam - Specification
65.
SimpsonA., FlemingH., Salford University Report dated July 1994 (Private communication), Sponsored by the British Rigid Urethane Foam Manufacturers’ Association (BRUFMA) and its members
66.
SimpsonA., FlemingH., Salford University Report dated November 1996 (Private communication), Sponsored by the British Rigid Urethane Foam Manufacturers’ Association (BRUFMA) and its members
