Experimental Damage Detection on a Wing Panel Using Vibration Deflection Shapes

Abstract

This paper discusses the use of a vibration method to detect fatigue cracks in inaccessible internal structures. On aircraft, the lower wing panels are highly stressed causing cracks to initiate from fastener holes inside the wing box. The wing panel internal sections are usually inspected using conventional nondestructive inspection techniques after removing the wing panels from the wing box structure. When a crack is detected during the inspection, it can sometimes be repaired by reinforcing the damaged wing panel integral stiffener with a set of repair doublers. Of concern is whether the repair is intact for extended periods of aircraft service. The integrity of the repair and the condition of the wing interior structure might be determined by measuring the vibration of the outer surface. To investigate this approach, a series of experiments was conducted. Two piezoceramic actuator patches were bonded on the outside of a wing panel above a stiffener to generate vibration up to 80 kHz. A scanning laser doppler vibrometer was used to measure the normal vibration of the outside of the panel over the crack/repair. The measurements were performed for both the healthy and damaged panel. It was found that a crack extending from a fastener hole to the free edge of a stiffener and loosening of a repair doubler could be detected by changes in the vibration response of the outside of the panel. The crack from the fastener hole was not detectable until it reached the free edge of the stiffener.

Get full access to this article

View all access options for this article.

References

1. Ness, S. and Sherlock, C.N. (1996). Nondestructive Testing Handbook, Vol 10, Nondestructive Testing Overview . American Society for Nondestructive Testing.

2. Sundaresan, M.J., Schulz, M.J., Hill, J., Wheater, E.A., Ferguson, F. and Pai, P.F. (1999). Damage detection on a wind turbine blade section . IMAC XVII Conference, Orlando, Fla, February 3-8.

3. Sundaresan, M.J., Ghoshal, A., Schulz, M.J., Ferguson, F., Pai, P.F. and Wilkerson, C. (1999). Damage detection using a laser vibrometer and active fiber composite patch . 6th International Conference on Composites Engineering, Orlando, Fla.

4. Doebling, S.W., Farrar, C.R., Prime, M.B. and Shevitz, D.W. (1996). Damage Identification and Health Monitoring of Structural and Mechanical Systems from Changes in their Vibration Characteristics: A Literature Review, Los Alamos National Laboratory Report LA-13070-VA5.

5. James, G.H. (April 1996). Development of structural health monitoring techniques using dynamics testing, Sandia Report: SAND96-0810, UC-706.

6. Simmermacher, T., James, G.H. III and Hurtado, J.E. (1997). Structural health monitoring of wind turbines . Proceedings of the International Workshop on Structural Health Monitoring (pp. 788-797 ), September 18-20, Stanford CA.

7. Chen, S., Venkatappa, S., Petro, S.H., Dajani, J.N. and GangaRao, H.V.S. (1998). Damage detection using scanning laser vibrometer . 3rd International Conference on Vibration Measurements by Laser Techniques, June 16-19, Ancona, Italy.

8. Waldron, K., Ghoshal, A., Schulz, M.J., Sundaresan, M.J., Ferguson, F., Pai, P.F. and Chung, J.H. (2002). Damage detection using finite elements and laser operational deflection shapes . J. Finite Elements in Analysis and Design, 38, 193-226 .

9. Pai, P.F., Oh, Y. and Lee, S.Y. (2002). Detection of defects in circular plates using a scanning laser vibrometer . Structural Health Monitoring: An International Journal, 1(1).

10.

10. Li, Jia (1998). Finite element modeling and damage detection on an aircraft panel. MS Thesis, North Carolina A&T State University.

11.

11. Schulz, M.J., Ghoshal, A., Sundaresan, M.J., Pai, P.F. and Chung, J.H. (2003). Theory of damage detection using constrained vibration deflection shapes . Structural Health Monitoring: An International Journal, 2(1).

12.

12. Laser Vibrometer Optics, Fiber Optic Vibrometer, Polytec PI, Auburn, MA, 01501.