Upcoming legislations aim to significantly reduce carbon dioxide and hydrocarbon emissions compared to current regulations. Accordingly, options have to be evaluated to not only convert the raw emissions in a catalytic converter, but also to reduce the raw emissions from the combustion process in the first place. Therefore, thermal piston top land coatings, which lead to an oscillating piston surface temperature were investigated on a single cylinder research engine using a gasoline RON95E10 fuel. Measurements were conducted at a compression ratio of 12.2 and a long Miller intake event. In this manuscript the results achieved with yttria stabilized zirconia in comparison to an uncoated piston are displayed. Significant effects of the coatings on the indicated efficiency could be observed mainly at low engine speeds and loads due to the high share of fuel energy in the wall heat losses and incomplete combustion. At these operating points, the reduction of wall heat losses can almost be fully transferred into indicated efficiency, leading to an increase in indicated efficiency of 6.3% by the yttria stabilized zirconia coating. At higher engine speeds and loads, the advantage in indicated efficiency vanishes and a decrease of 0.5% can be observed. Near full load operation the indicated efficiency slightly lower. However, the effects of a thermal swing coating on combustion efficiency and wall heat losses strongly depend on the operation conditions.
SamarasZCKontsesADimaratosA, et al. A European regulatory perspective towards a Euro 7 proposal. In: SAE technical paper series, 21 June 2022. Warrendale, PA: SAE International.
2.
LeachFKalghatgiGStoneRMilesP. The scope for improving the efficiency and environmental impact of internal combustion engines. Transp Eng2020; 1.
3.
WangZShuaiSLiZYuW. A review of energy loss reduction technologies for internal combustion engines to improve brake thermal efficiency. Energies2021; 14: 6656.
4.
AchenbachJFischerMLehrheuerBGuentherMPischingerS. Influence of thermal piston insulation on the indicated efficiency of SI-engines. In: COMODIA 2022, 5–8 July 2022, Sapporo, Japan.
5.
HasseCBolligMPetersNDwyerHA. Quenching of laminar iso-octane flames at cold walls. Combust Flame2000; 122: 117–129.
6.
MemmeSWallaceJS. The influence of thermal barrier coating surface roughness on spark-ignition engine performance and emissions. In: ASME 2012 Internal combustion engine division fall technical conference, Vancouver, BC, 23–26 September 2012, pp.893–905. American Society of Mechanical Engineers.
7.
BüyükkayaEEnginTCeritM. Effects of thermal barrier coating on gas emissions and performance of a LHR engine with different injection timings and valve adjustments. Energy Convers Manag2006; 47: 1298–1310.
8.
AndrieMKokjohnSPaliwalS, et al. Low heat capacitance thermal barrier coatings for internal combustion engines. In: SAE technical paper series, 9 April 2019. Warrendale, PA: SAE International.
9.
ChanSHKhorKA. The effect of thermal barrier coated piston crown on engine characteristics. J Mater Eng Perform2000; 9: 103–109.
10.
KamoRAssanisDBryzikW. Thin thermal barrier coatings for engines. SAE Int J Engines1989; 98: 131–136.
UchidaN. A review of thermal barrier coatings for improvement in thermal efficiency of both gasoline and diesel reciprocating engines. Int J Engine Res2022; 23: 3–19.
13.
BabuAKoutsakisGKokjohnS, et al. Experimental and analytical study of temperature swing piston coatings in a medium-duty diesel engine. In: WCX SAE world congress experience. Warrendale, PA: SAE International.
14.
Uczak de GoesWMarkocsanNGuptaM. Thermal Swing Evaluation of thermal spray coatings for internal combustion engines. Coatings2022; 12: 830.
15.
DhomneSMahalleAM. Thermal barrier coating materials for SI engine. J Mater Res Technol2019; 8: 1532–1537.
16.
VaßenRMackDETandlerM, et al. Unique performance of thermal barrier coatings made of yttria-stabilized zirconia at extreme temperatures (>1500°C). J Am Ceram Soc2021; 104: 463–471.
BobzinKLugscheiderEBagcivanN. Thermal cycling behavior of yttria stabilized zirconia and lanthanum zirconate as graded and bilayer EB-PVD thermal barrier coatings. High Temp Mater Process2006; 10: 103–116.
19.
PlanquesPVidalVLoursP, et al. Mechanical properties of yttria-stabilised-zirconia for thermal barrier coating systems effects of testing procedure and thermal aging. In: ITSC 2017 - international thermal spray conference and exposition (ed ASM International), Dusseldorf, Germany, 2017, pp.302–307.
20.
BryzikWKamoR. TACOM/Cummins Adiabatic Engine Program. In: SAE international congress and exposition. Warrendale, PA: SAE International.
21.
WoschniGSpindlerWKolesaK. Heat insulation of combustion chamber walls — a measure to decrease the fuel consumption of I.C. engines?SAE technical paper1987. DOI: 10.4271/870339.
22.
KawaguchiAIgumaHYamashitaH, et al. Thermo-swing wall insulation technology; - a novel heat loss reduction approach on engine combustion chamber. In: SAE technical paper series, 24 October 2016. Warrendale, PA: SAE International.
23.
SomhorstJUczak de GoesWOevermannM, et al. Experimental evaluation of novel thermal barrier coatings in a single cylinder light duty diesel engine. In: SAE technical paper series, 15 September 2019. Warrendale, PA: SAE International.
24.
AndruskiewiczPNajtPDurrettR, et al. Analysis of the effects of wall temperature swing on reciprocating internal combustion engine processes. Int J Engine Res2018; 19: 461–473.
25.
ChérelJZaccardiJ-MBouteillerBAllimantA. Experimental assessment of new insulation coatings for lean burn spark-ignited engines. Oil Gas Sci Technol2020; 75: 11.
26.
RumplmayrPSchuttingEEichlsederH. Experimental investigation of anodic oxidation coatings to reduce wall heat losses on a diesel engine. Wien, 2020.
27.
AndruskiewiczPNajtPDurrettRPayriR. Assessing the capability of conventional in-cylinder insulation materials in achieving temperature swing engine performance benefits. Int J Engine Res2018; 19: 599–612.
28.
GordonDWoutersCWickM, et al. Development and experimental validation of a real-time capable field programmable gate array–based gas exchange model for negative valve overlap. Int J Engine Res2020; 21: 421–436.
29.
WoutersCBurkardtPFischerMBlombergMPischingerS. Effects of stroke on spark-ignition combustion with gasoline and methanol. Int J Engine Res2022; 23: 804–815.
30.
WoutersCBurkardtPPischingerS. Limits of compression ratio in spark-ignition combustion with methanol. Int J Engine Res2022; 23: 793–803.
31.
Spindt RS. Air-fuel ratios from exhaust gas analysis. SAE Transactions. 1966; 74: 788–793.
HeywoodJB. Internal combustion engine fundamentals. New York: McGraw-Hill Inc., 1988.
34.
Deutsches Institut für Normung e.V. 21920-2. Geometrische Produktspezifikation (GPS) – Oberflächenbeschaffenheit: Profile – Teil 2: Begriffe und Kenngrößen für die Oberflächenbeschaffenheit.
35.
EspositoSMauermannPLehrheuerB, et al. Effect of engine operating parameters on space- and species-resolved measurements of engine-out emissions from a single-cylinder spark ignition engine. In: SAE technical paper series. Warrendale, PA: SAE International.
36.
FischerMLehrheuerBPischingerS. Evaluation of the near-wall gas composition in SI-engines using fast gas sampling. Int J Engine Res2023; 24: 3376–3387.
37.
ChoiSKolodziejCPHothA, et al. Development and validation of a three pressure analysis (TPA) GT-power model of the CFR F1/F2 engine for estimating cylinder conditions. In: SAE technical paper series, 10 April 2018. Warrendale, PA: SAE International.
38.
WoschniG. A universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine, 1967.
39.
SchwarzC. Simulation of transient operation of supercharged Diesel engines. Technische University, München.
40.
SpindtRS. Air-fuel ratios from exhaust gas analysis. SAE technical paper 650507, 1965.
41.
Gamma Technologies. GT-SUITE: flow theory manual: Version 2019. Westmondt: Gamma Technologies, 2019.
42.
CourantRFriedrichsKLewyH. On the partial difference equations of mathematical physics. IBM J Res Dev1967; 11: 215–234.
43.
WentworthJT. More on origins of exhaust hydrocarbon deposit location, and surface roughness. SAE Trans1972; 1972: 2726–2734.
44.
YamashitaCYamashitaHKawaguchiA. Development of the heat insulation coating by temperature swing for the combustion chamber wall of gasoline engine. In: 2019 JSAE Congress (Autumn), Sendai, 9–11 Japan October2019, Paper no. JSAE 20196086.
45.
KosakaHWakisakaYNomuraY, et al. Concept of “temperature swing heat insulation” in combustion chamber walls, and appropriate thermo-physical properties for heat insulation coat. SAE Int J Engines2013; 6: 142–149.
46.
PoolaRNagalingamBGopalakrishnanK. Performance of Thin-ceramic-coated combustion chamber with gasoline and methanol as fuels in a two-stroke SI engine. SAE technical paper1994.
47.
Jennings MarkJMorelT. Modeling of turbulent heat transfer with applications to IC engines. SAE Transactions1987; 96: 523–533.
48.
GlarborgPBentzenLLB. Chemical effects of a high CO2 concentration in oxy-fuel combustion of methane. Energy Fuels2008; 22: 291–296.
49.
LuoHUchitomiSNishidaK, et al. Experimental investigation on Fuel Film Formation by spray impingement on flat walls with different surface roughness. Atomization Sprays2017; 27: 611–628.
MahulkarAVMarinGBHeynderickxGJ. Droplet–wall interaction upon impingement of heavy hydrocarbon droplets on a heated wall. Chem Eng Sci2015; 130: 275–289.
52.
MinKChengWHeywoodJ. The effects of crevices on the engine-out hydrocarbon emissions in SI engines. SAE Trans1994; 103: 371–385.
53.
FischerMNolteAWuX, et al. Influence of yttria-stabilized zirconium oxide thermal swing coating on the flame-wall interaction in spark ignition engines. Energies2023; 16: 2872.
54.
SileghemLAlekseevVAVancoillieJ, et al. Laminar burning velocity of gasoline and the gasoline surrogate components iso-octane, n-heptane and toluene. Fuel2013; 112: 355–365.
55.
Date AW. Analytic combustion: with thermodynamics, chemical kinetics and mass transfer. 2nd ed.Singapore: Springer, 2020.
56.
EspositoS. Analysis of gaseous pollutant emissions from spark-ignition engines. Dissertation, RWTH, Aachen, 2020.
57.
WuHHochgrebS. Numerical simulation of post-flame oxidation of hydrocarbons in spark ignition engines. SAE Int J Engines1997; 106: 1453–1462.
58.
FilipiZSAssanisDN. The effect of the stroke-to-bore ratio on combustion, heat transfer and efficiency of a homogeneous charge spark ignition engine of given displacement. International Journal of Engine Reserach 2000; 1: 191–208.
ThompsonNDWallaceJS. Effect of engine operating variables and piston and ring parameters on crevice hydrocarbon emissions. SAE Transactions 1994; 103: 718–736.
61.
DemuynckJDe PaepeMVerhaertIVerhelstS. Heat loss comparison between hydrogen, methane, gasoline and methanol in a spark-ignition internal combustion engine. Energy Proc2012; 29: 138–146.
