This article describes the use of a Lagrangian discrete droplet model to evaluate the liquid fuel impingement characteristics on the internal surfaces of an early injection gasoline direct injection engine. This study focuses on fuel impingement on the intake valve and cylinder liner between start of injection and 20° after start of injection using both a single- and a multi-component fuels. The single-component fuel used was iso-octane and the multi-component fuel contained fractions of iso-pentane, iso-octane and n-decane to represent the light, medium and heavy fuel fractions of gasoline, respectively. A detailed description of the impingement and liquid film modelling approach is also provided. Fuel properties, wall surface temperature and droplet Weber number and Laplace number were used to quantify the impingement regime for different fuel fractions and correlated well with the predicted onset of liquid film formation. Evidence of film stripping was seen from the liquid film formed on the side of the intake valve head with subsequent ejected droplets being a likely source of unburned hydrocarbons and particulate matter emissions. Differences in impingement location and subsequent location of liquid film formation were also observed between single- and multi-component fuels. A qualitative comparison with experimental cylinder liner impingement data showed the model to well predict the timing and positioning of the liner fuel impingement.
StevensESteeperR.Piston wetting in an optical DISI engine: fuel films, pool fires, and soot generation. SAE technical paper 2001-01-1203, 2001.
3.
AleiferisPGVan RomundeZR.An analysis of spray development with iso-octane, n-pentane, gasoline, ethanol and n-butanol from a multi-hole injector under hot fuel conditions. Fuel2013; 105: 143–168.
4.
Serras-PereiraJAleiferisPRichardsonDWallaceS. Spray development in a direct-injection spark-ignition engine. SAE technical paper 2007-01-2712, 2007.
5.
Serras-PereiraJAleiferisPGRichardsonD.Imaging and heat flux measurements of wall impinging sprays of hydrocarbons and alcohols in a direct-injection spark-ignition engine. Fuel2012; 91: 264–297.
6.
Serras-PereiraJ.Spray formation and combustion of alcohols and gasoline in a direct-injection spark-ignition engine. PhD Thesis, University College London, London, 2010.
7.
Van RomundeRZ. Factors affecting the development of sprays produced by multihole injectors for direct-injection engine applications. PhD Thesis, University College London, London, 2011.
8.
BeavisNJIbrahimSSManickamPKMalalasekeraW. Characteristics of GDI engine flow structures. In: 12th international congress, engine combustion processes, current problems and modern technologies (ed LeipertzA), Ludwigsburg, 12–13 March 2015, pp.385–396. Erlangen: ESYTEC GmbH, https://dspace.lboro.ac.uk/2134/20016
9.
KellerPKnorschTWensingMHasseC. Experimental and numerical analysis of iso-octane/ethanol sprays under gasoline engine conditions. Int J Heat Mass Tran2015; 84: 497–510.
10.
Serras-PereiraJvan RomundeZAleiferisPGRichardsonDWallaceSCracknellRF. Cavitation, primary break-up and flash boiling of gasoline, iso-octane and n-pentane with a real-size optical direct-injection nozzle. Fuel2010; 89: 2592–2607.
11.
YakhotVOrszagSA. Renormalization group analysis of turbulence. I. Basic theory. J Sci Comput1986; 1: 3–51.
12.
YakhotVOrszagSAThangamSGatskiTBSpezialeCG. Development of turbulence models for shear flows by a double expansion technique. Phys Fluids A: Fluid1992; 4: 1510–1520.
13.
AngelbergerCPoinsotTDelhayB.Improving near-wall combustion and wall heat transfer modeling in SI engine computations. SAE technical paper 972881, 1997.
14.
GosmanADIoannidesSI.Aspects of computer simulation of liquid-fuelled combustors. J Energy1983; 7: 482–490.
15.
PilchMErdmanCA.Use of breakup time data and velocity history data to predict the maximum size of stable fragments for acceleration-induced breakup of a liquid drop. Int J Multiphas Flow1987; 13: 741–757.
16.
O’RourkePJ.Collective drop effects on vaporising liquid sprays. PhD Thesis, University of Princeton, Princeton, NJ, 1981.
17.
SchmidtDPRutlandCJ.A new droplet collision algorithm. J Comput Phys2000; 164: 62–80.
18.
AamirMAWatkinsAP. Dense propane spray analysis with a modified collision model. In: 15th annual conference on liquid atomization and spray systems, Toulouse, France, 15–17 July 1999. France: ILASS-Europe.
19.
NordinN.Complex chemistry modelling of diesel spray combustion. PhD Thesis, Chalmers University of Technology, Göteborg, 2001.
20.
SendaJFujimotoHG.Multidimensional modeling of impinging sprays on the wall in diesel engines. Appl Mech Rev1999; 52: 119–138.
21.
SendaJKandaTAl-RoubMFarrellPVFukamiTFujimotoHG. Modeling spray impingement considering fuel film formation on the wall. SAE technical paper 970047, 1997.
22.
AshidaKTakahashiTTanakaTYeomJ-KSendaJFujimotoHG. Spray-wall interaction model considering superheating degree of the wall surface. In: Eighth international conference on liquid atomization and spray systems, Pasadena, CA, USA, 16–20 July 2000. USA: ILASS-Americas.
23.
SendaJKobayashiMIwashitaSFujimotoHG. Modeling of diesel spray impinging on flat wall. In: The international symposium on diagnostics and modeling of combustion in internal combustion engines (COMODIA), Yokohama, Japan, 11–14 July 1994, pp.411–416. Japan: JSME.
24.
MatsudaTSendaJ.Modeling on spray-wall interaction for direct gasoline injection engines. J JSME2003; 69: 2698–2705.
25.
BaiCGosmanAD.Development of methodology for spray impingement simulation. SAE technical paper 950283, 1995.
26.
RosaNGVilledieuPDewitteJLavergneG. A new droplet-wall interaction model. In: Tenth international conference on liquid atomization and spray systems, Kyoto, Japan, 27 August–1 September 2006, Paper ID ICLASS06-167. Japan: ILASS-Japan.
27.
HabchiC.A comprehensive model for liquid film boiling in internal combustion engines. Oil Gas Sci Technol2010; 65: 331–343.
28.
SpieglerPHopenfeldJSilberbergMBumpusCFNormanA. Onset of stable film boiling and the foam limit. Int J Heat Mass Tran1963; 6: 987–989.
29.
BaiCGosmanAD.Mathematical modelling of wall films formed by impinging sprays. SAE technical paper 960626, 1996.
30.
WhiteFM. Mass and heat transfer. 1st ed. Reading, MA: Addison-Wesley, 1988.
31.
FriedrichMALanHWegenerJLDrallmeierJAArmalyBF. A separation criterion with experimental validation for shear-driven films in separated flows. J Fluid Eng2008; 130: 051301.
32.
FoucartHHabchiCLe CozJFBaritaudT. Development of a three dimensional model of wall fuel liquid film for internal combustion engines. SAE technical paper 980133, 1998.
33.
Al-RoubMFarrellPVSendaJ.Near wall interaction in spray impingement. SAE technical paper 960863, 1996.
34.
Al-RoubM.Hydrodynamics and heat transfer of multiple droplet impingement. PhD Thesis, University of Wisconsin–Madison, Madison, WI, 1996.
35.
StantonDWRutlandCJ.Multi-dimensional modeling of heat and mass transfer of fuel films resulting from impinging sprays. SAE technical paper 980132, 1998.
36.
MaroteauxFLloryDLe CozJ-FHabchiC. Liquid film atomization on wall edges, separation criterion and droplets formation model. J Fluid Eng2002; 124: 565–575.
37.
MaroteauxFLloryDLe CozJ-FHabchiC. Potential of inertial instabilities for fuel film separation in port fuel injection engine conditions. Int J Engine Res2003; 4: 11–26.
38.
Serras-PereiraJAleiferisPGRichardsonDWallaceS. Mixture preparation and combustion variability in a spray-guided DISI engine. SAE technical paper 2007-01-4033, 2007.
39.
RimmerJET. An optical investigation into the effect of fuel spray, turbulent flow and flame propagation on DISI engine performance. PhD Thesis, Loughborough University, Loughborough, 2011.
40.
DrakeMCFanslerTDSolomonASSzekelyGA. Piston fuel films as a source of smoke and hydrocarbon emissions from a wall-controlled spark-ignited direct-injection engine. SAE technical paper 2003-01-0547, 2003.
41.
YaoSCCaiKY.The dynamics and leidenfrost temperature of drops impacting on a hot surface at small angles. Exp Therm Fluid Sci1988; 1: 363–371.
