Factors determining the success or failure of combustion initiation using a glow plug have been investigated through experimental work on a single cylinder, common rail diesel engine with a geometric compression ratio of 15.5, and a quiescent combustion bomb with optical access. A glow plug was required to avoid engine misfires when bulk gas temperature at the start of injection was less than 413 °C. The distance between the glow plug and the spray edge, the glow plug temperature, and the bulk gas temperature were important factors in meeting two requirements for successful ignition: a minimum local temperature of 413 °C and a minimum air/fuel vapour equivalence ratio of 0.15–0.35.
McGheeMJShaylerPJLa RoccaAMurphyMPeggI.The influence of injection strategy and glow plug temperature on cycle by cycle stability under cold idling conditions for a low compression ratio, HPCR diesel engine. SAE Int J Engines2012; 5(3): 923–937.
2.
McGheeMJShaylerPJLa RoccaAMurphyMPeggI. Investigations of injection strategies for stable cold idling of an HPCR diesel engine with a compression ratio of 15.5:1. In: IMechE conference C1342 fuel systems for IC engines, London, 14–15 March 2012. Cambridge: Woodhead Publishing.
3.
WeilenmannMFavezJAlvarezR.Cold-start emissions of modern passenger cars at different low ambient temperatures and their evolution over vehicle legislation categories. Atmos Environ2009; 43(15): 2419–2429.
4.
BielaczycPMerkiszJPielechaJ.Investigation of exhaust emissions from DI diesel engine during cold and warm start. SAE paper 2001-01-1260, 2001.
5.
BielaczycPMerkiszJPielechaJ.A method of reducing the exhaust emissions from DI diesel engines by the introduction of a fuel cut off system during cold start. SAE paper 2001-01-3283, 2001.
6.
MacMillanDLa RoccaAShaylerPJMurphyMPeggIG.The effect of reducing compression ratio on the work output and heat release characteristics of a DI diesel under cold start conditions. SAE paper 2008-01-1306, 2008.
7.
PacaudPPerrinHLagetO.Cold start on diesel engine: is low compression ratio compatible with cold start requirements? SAE paper 2008-01-1310, 2008.
8.
CursenteVPacaudPGatellierB.Reduction of the compression ratio on a HSDI diesel engine: combustion design evolution for compliance the future emission standards. SAE paper 2008-01-0839, 2008.
9.
BeatriceCAvolioGGiacomoNDGuidoC.Compression ratio influence on the performance of an advanced single-cylinder diesel engine operating in conventional and low temperature combustion mode. SAE paper 2008-01-1678, 2008.
10.
McGheeM.Factors influencing cycle-by-cycle combustion characteristics of a diesel engine under cold idling conditions. PhD Thesis, University of Nottingham, Nottingham, 2012.
KernCDresslerWLindemannGRothackerV.An innovative glow system for modern diesel engines. SAE paper 1999-01-1240, 1999.
13.
PayriFBroatchASerranoJRRodríguezLFEsmorísA.Study of the potential of intake air heating in automotive DI diesel engines. SAE paper 2006-01-1233, 2006.
14.
MacMillanD.Influences on the cold start behaviour of a diesel engine at reduced compression ratio. PhD Thesis, University of Nottingham, Nottingham, 2009.
15.
WalterBPerrinHDumasJPLagetO.Cold operation with optical and numerical investigations on a low compression ratio diesel engine. SAE paper 2009-01-2714, 2009.
16.
ChartierCAronssonUAnderssonO.Effect of injection strategy on cold start performance in an optical light duty DI diesel engine. SAE paper 2009-24-0045, 2009.
17.
MuellerCMusculusM.Glow plug assisted ignition and combustion of methanol in an optical DI diesel engine. SAE paper 2001-01-2004, 2001.
18.
PastorJVBermúdezVGarcía-OliverJMRamírez-HernándezJG.Influence of spray-glow plug configuration on cold start combustion for high-speed direct injection diesel engines. Energy2011; 36(9): 5486–5496.
19.
PastorJVGarcía-OliverJMPastorJMRamírez-HernándezJG.Ignition and combustion development for high speed direct injection diesel engines under low temperature cold start conditions. Fuel2011; 90(4): 1556–1566.
20.
ImaokaYNishizawaTLioSHasegawaMTerajiAKawamotoK.Three-dimensional numerical analysis of diesel combustion under cold ambient conditions. Int J Engine Res2015; 16(1): 68–80.
21.
BroatchARuizSMargotXGilA.Methodology to estimate the threshold in-cylinder temperature for self-ignition of fuel during cold start of diesel engines. Energy2010; 35: 2251–2260.
22.
MacMillanDLa RoccaAShaylerPJ.Investigating the effects of multiple pilot injections on stability at cold idle for a DI diesel engine. SAE paper 2009-01-0612, 2009.
23.
HeywoodJB.Internal combustion engine fundamentals. New York: McGraw-Hill, 1988.
24.
BruntMFRaiAEmtageAL.The calculation of heat release energy from engine cylinder pressure data. SAE paper 981052, 1998.
25.
BruntMPlattsK.Calculation of heat release in direct injection diesel engines. SAE paper 1999-01-0187, 1999.
26.
EdwardsCFSiebersDLHoskinDH.A study of the autoignition process of a diesel spray via high speed visualization. SAE T1992; 101(3): 187–204.
ANSYS fluent 14.0 theory guide. (accessed through user manual in July 2015).
29.
BekdemirC.Numerical modeling of diesel spray formation and combustion. MSc Thesis, Eindhoven University of Technology, Eindhoven, 2008.
30.
Mohamed IsmailHNgHKGanS. Evaluation of non-premixed combustion and fuel spray models for in-cylinder diesel engine simulation. Appl Energ2012; 90: 271–279.
31.
AbbasGFukudaKBalachandarRBarronR.Numerical investigation of spray characteristics of diesel alternative fuels. SAE paper 2012-01-1265, 2012.
32.
LiuABMatherDReitzRD.Modeling the effects of drop drag and breakup on fuel sprays. SAE paper 930072, 1993.
33.
MillerRSHarstadKBellanJ.Evaluation of equilibrium and non-equilibrium evaporation models for many droplet gas-liquid flow simulations. Int J Multiphas Flow1998; 24(6): 1025–1055.
34.
SazhinSSKristyadiTAbdelghaffarWAHeikalMR.Models for fuel droplet heating and evaporation: comparative analysis. Fuel2006; 85: 1613–1630.
35.
Guan JhongWChia JuiCYu HsuanSYong YuanK. CFD modelling of a turbo-charged common-rail diesel engine. SAE paper 2013-32-9103, 2013.
DesantesJMGarcia-OliverJMPastorJMRamirez-HernandezJG.Influence of nozzle geometry on ignition and combustion for high-speed direct injection diesel engines under cold start conditions. Fuel2011; 90: 3359–3368.
38.
AssanisDNFilipiZSFivelandSBSyrimisM.A predictive ignition delay correlation under steady-state and transient operation of a direct injection diesel engine. J Eng Gas Turb Power2003; 125(2): 450–457.
