The purpose of this study is to analyse the differences in the combustion process, and pollutants formation (especially soot) due to top-hat and boot injection-rate shapes at one specific high-load point of a single-cylinder small-bore diesel engine using multidimensional engine simulations. The simulations are performed using a response interactive flamelet model with detailed chemical kinetics. A detailed chemistry-based soot model is used for the prediction of soot emissions. The heights of the first and second stages of the boot shape are varied to observe the effect of the injected fuel mass distribution. In addition, results of boot shapes are compared with a trapezoidal (top-hat) shape. A detailed analysis of soot formation and oxidation is also presented for some selected rate shapes. Through computational analysis it is shown that the boot shapes have the potential to decrease combustion-generated noise and to lower emissions at the investigated load point compared to the top-hat shape. Variations in the temporal distribution of the injected fuel mass show that a lower height of the first stage and a higher height of the second stage of the boot shape result in a relatively slower rise of heat release (lower combustion-generated noise) in the early part of combustion and enhanced soot oxidation as a result of higher spray momentum near the end of injection.
WakisakaY.AzetsuA.Effects of fuel injection rate shaping on combustion and emission formation in intermittent spray. SAE paper 2002-01-1159, 2002.
2.
SeebodeJ.Dieselmotorische einspritzratenformung unter dem einfluss von druckmodulation und nadelsitzdrosselung. PhD Thesis, University of Hannover, Germany, 2004.
3.
DesantesJ. M.BenajesJ.MolinaS.GonzálezC. A.The modification of fuel injection rate in heavy-duty diesel engines, part 1: effects on engine performance and emissions. Appl. Therm. Engng., 2004, 24, 2701–2714.
4.
DesantesJ. M.BenajesJ.MolinaS.GonzálezC. A.The modification of fuel injection rate in heavy-duty diesel engines, part 2: effects on combusion. Appl. Therm. Engng., 2004, 24, 2715–2726.
5.
TanabeK.KohketsuS.NakayamaS.Effect of fuel injection rate control on reduction of emissions and fuel consumption in a heavy-duty direct-injection diesel engine. SAE paper 2005-01-0907, 2005.
6.
PajotO.HouilleS.VidalF.DabireauF.StegemannJ.BrauerM.RoelleT.SeiffertA.Injection rate shaping with the twin common rail system: a coupled experimental and modeling investigation. Injection rate shaping with the twin common rail system: a coupled experimental and modeling investigation. In Proceedings of the Diesel Engine Conference, Lyon, France, 31 May–1 June 2006.
7.
KastnerO.AtzlerF.RotondiR.WeigandA.Evaluation of injection strategies for passenger car diesel engines to meet Euro 6 legislation limits. Conference on Thermo- and Fluid Dynamic Processes in Diesel Engines, 2008.
8.
JunejaH.RaY.ReitzR. D.Optimization of injection rate shape using active control of fuel injection. SAE paper 2004-01-0530, 2004.
9.
MeyerS.KrauseA.KromeD.MerkerG. P.Ein flexibles piezo-common-rail system mit direktgesteuerter duesennadel. Motortech. Zeil., 2002, 63, 86–93.
10.
StegemannJ.Dieselmotorische einspritzverlaufsformung mit piezoaktuierten experimentaleinspritzsystemen. PhD Thesis, University of Hannover, Germany, 2004.
11.
StegemannJ.SeebodeJ.BaltesJ.BaumgartenC.MerkerG. PInfluence of throttle effects at the needle seat on the spray characteristics of a multihole injection nozzle. In Proceedings of the ILASS Europe Conference on Liquid atomization and spray systems, Zaragoza, Spain, 9–11 September 2002, pp. 31–36.
12.
StegemannJ.MeyerS.RölleT.MerkerG. P.Injection system for fully variable control of the shape. Motortech. Zeit., 2004, 65, 13–16.
13.
SeebodeJ.MerkerG. P.LettmannH.Injection strategies under the influence of pressure modulation and free rate shaping in modern direct injection diesel engines. CIMAC Congress, Kyoto, Japan, 2004.
14.
RottmannM.MenneC.PischingerS.LuckhchouraV.PetersN.Injection rate shaping investigations on a small bore direct injection diesel engines. SAE paper 2009-01-0850, 2009.
15.
LuckhchouraV.RobertF.-X.PetersN.RottmannM.PischingerS.Experimental and numerical investigation of injection rate shaping in a small-bore direct-injection diesel engine. In Proceedings of the International Symposium on Towards clean diesel engines, TCDE 2009, 4–5 June 2009, available from, 2009, available from http://sunsite.informatik.rwth-aachen.de/Publications/CEUR-WS/Vol-452/ (accessed 27 May 2009).
16.
PetersN.Turbulent combustion, 2000 (Cambridge University Press, Cambridge, UK).
17.
PitschH.Modellierung der zündung und schadstoffbildung bei der dieselmotorischen verbrennung mit hilfe eines interaktiven flamelet-modells. PhD Thesis, RWTH Aachen, 1997.
18.
BarthsH.AntoniC.PetersN.Three-dimensional simulation of pollutant formation in a DI diesel engine using multiple interactive flamelets. SAE paper 982459, 1998.
19.
HergartC. A.BarthsH.PetersN.Modeling the combustion in a small-bore diesel engine using a method based on representative interactive flamelets. SAE paper 1999-01-3550, 1999.
20.
HasseC.PetersN.Modeling of ignition mechanisms and pollutant formation in direct-injection diesel engines with multiple injections. Int. J. Eng. Rese., 2005, 6, 231–246.
21.
LuckhchouraV.WonH. W.SharmaA.PaczkoG.PetersN.Investigation of combustion noise development with variation in start of injection using 3-dimensional simulations by applying representative interactive flamelet (RIF) model. SAE paper 2008-01-0950, 2008.
22.
GirimajiS. S.Assumed -PDF model for turbulent mixing: validation and extension to multiple scalar mixing. Combust. Sci. Technol., 1991, 18, 177–196.
WilliamsF. A.Spray combustion and atomization. Phys. Fluids, 1958, 541–545.
25.
CroweC. T.SharmaM. P.StockD. E.The particle-source-in cell (psi-cell) model for gas-droplet flows. J. Fluids Engng., 1977, 99, 325–332.
26.
AmsdenA. A.KIVA-3: A KIVA program with block-structured mesh for complex geometries, technical report LA-12503-MS, Los Alamos National Laboratories, 1993.
27.
BealeJ. C.ReitzR. D.Modeling spray atomization with the Kelvin–Helmholtz/Rayleigh–Taylor hybrid model. Atomization Sprays, 1999, 9, 623–650.
28.
AntoniC.Untersuchung des verbrennungsvorgangs im direkteinspritzenden dieselmotor mit zyklusaufgelöster emissionsspektroskopie. PhD Thesis, Rheinisch-Westphälische Technische Hochschule Aachen, 1998.
29.
BarthsH.Simulation of diesel engine and gas turbine combustion using multiple flamelets with detailed chemistry. PhD Thesis, RWTH Aachen, 2001.
30.
BolligM.Berechnung laminarer kohlenwasserstoffflammen in hinblick auf die stickoxidbildung in verbrennungsmotoren. PhD Thesis, RWTH Aachen, 1998.
31.
FrenklachM.HarrisS. J.Aerosol dynamics modeling using the method of moments. J. Collord Interface Sci., 1987, 118, 252–261.
32.
MaussF.Entwicklung eines kinetischen modells der ruß bildung mit schneller polymerisation. PhD Thesis, RWTH Aachen, 1997.
33.
EngJ. A.Characterization of pressure waves in HCCI combustion. SAE paper 2002-01-2859, 2002.
34.
DiwakarR.SinghS.NOx and soot reduction in diesel engine premixed charge compression ignition combustion: a computational investigation. Int. J. Eng. Res. 2008, 9(3), 195–214. DOI: 10.1243/14680874JER00308.
