Experimental studies on friction stir welding of aluminium alloy 5083 and prediction of temperature distribution using arbitrary Lagrangian–Eulerian-based finite element method
Restricted accessResearch articleFirst published online May, 2022
Experimental studies on friction stir welding of aluminium alloy 5083 and prediction of temperature distribution using arbitrary Lagrangian–Eulerian-based finite element method
The present work focused on welding aluminium alloy 5083 using the friction stir welding process. Suitable welding process parameters were identified to fabricate a defect-free butt joint with a tool rotational speed of 1600 rpm, traverse speed of 20 mm/min and tilt angle of 3°. The microstructure at the nugget zone, thermo mechanically affected zone, heat-affected zone and base metal zone are examined. Mechanical properties of the weldment exhibited promising results with an average joint efficiency and hardness of 75.70% and 94.0 ± 5.0 vickers hardness, respectively. Fractography revealed ductile mode of failure in base and weld metal tensile samples. Furthermore, a 3D thermomechanical finite element model was utilized to simulate the friction stir welding process using the selected process parameters. Arbitrary Lagrangian–Eulerian-based model aided in predicting residual stress distributions and thermal history during the friction stir welding process.
TaheriHKilpatrickMNorvallsM, et al.Investigation of nondestructive testing methods for friction stir welding. Metals (Basel)2019; 9: 1–22.
2.
MyungDNohWKimJH, et al.Probing the mechanism of friction stir welding with ALE based finite element simulations and its application to strength prediction of welded aluminum. Met. Mater. Int2021; 27: 650–666.
3.
IqbalMPTripathiAJainR, et al.Numerical modelling of microstructure in friction stir welding of aluminium alloys. Int. J. Mech. Sci2020; 185: 105882.
4.
AhmedMMZAtayaSEl-Sayed SelemanMM, et al.Heat input and mechanical properties investigation of friction stir welded AA5083/AA5754 and AA5083/AA7020. Metals (Basel)2021; 11: 1–20.
5.
LombardHHattinghDGSteuwerA, et al.Effect of process parameters on the residual stresses in AA5083-H321 friction stir welds. Mater. Sci. Eng. A2009; A501: 119–124.
6.
KumarRSinghKPandeyS. Process forces and heat input as function of process parameters in AA5083 friction stir welds. Trans. Nonferrous Met. Soc. China2012; 22: 288–298.
7.
KanwerSAPandeySSchaperM, et al.Effect of process parameters on friction stir welding of aluminum alloy 2219-T87. Int J Adv Manuf Technol2010; 50: 941–952.
8.
VorontsovAZykovaAChumaevskiiA, et al.Advanced high-strength AA5083 welds by high-speed hybrid laser-arc welding. Mater. Lett2021; 291: 129594.
9.
TamasgavabariREbrahimiARAbbasiSM, et al.Effect of harmonic vibration during gas metal arc welding of AA-5083 aluminum alloy on the formation and distribution of intermetallic compounds. J. Manuf. Process2020; 49: 413–422.
10.
KunduJSinghH. Friction stir welding of AA5083 aluminium alloy: multi-response optimization using taguchi-based grey relational analysis. Adv. Mech. Eng2016; 8: 1–10.
11.
JainVKSMuhammedPMMuthukumaranS, et al.Microstructure, mechanical and sliding wear behavior of AA5083 – B4C / SiC / TiC surface composites fabricated using friction stir processing. Trans. Indian Inst Met2018; 71: 1519–1529.
12.
MiknoZBartnikZ. Heating of electrodes during spot resistance welding in FEM calculations. Arch. Civ. Mech. Eng2016; 16: 86–100.
13.
RagabMLiuHYangGJ, et al.Friction stir welding of 1Cr11Ni2W2MoV martensitic stainless steel: numerical simulation based on coupled eulerian lagrangian approach supported with experimental work. Appl. Sci2021; 11: 1–18.
14.
AjriARohatgiNShinYC. Analysis of defect formation mechanisms and their effects on weld strength during friction stir welding of Al 6061-T6 via experiments and finite element modeling. Int. J. Adv. Manuf. Technol2020; 107: 4621–4635.
15.
GrujicicMRamaswamiSSnipesJS, et al.Prediction of the grain-microstructure evolution within a friction stir welding (FSW) joint via the use of the monte carlo simulation method. J. Mater. Eng. Perform2015; 24: 3471–3486.
16.
SarikavakY. An advanced modelling to improve the prediction of thermal distribution in friction stir welding (FSW) for difficult to weld materials. J. Brazilian Soc. Mech. Sci. Eng2021; 43: 1–14.
17.
SalloomiKNAl-SumaidaeS. Coupled eulerian–lagrangian prediction of thermal and residual stress environments in dissimilar friction stir welding of aluminum alloys. Journal of Advanced Joining Processes2021; 3: 100052.
18.
GuoYMaYZhangX, et al.Study on residual stress distribution of 2024-T3 and 7075-T6 aluminum dissimilar friction stir welded joints. Eng. Failure Anal2020; 118: 104911.
19.
AlinaghianIAminiSHonarpishehM. Residual stress, tensile strength, and macrostructure investigations on ultrasonic assisted friction stir welding of AA 6061-T6. J Strain Analysis2018; 53: 494–503.
20.
El-SayedMMShashAYMahmoudTS, et al.Effect of friction stir welding parameters on the peak temperature and the mechanical properties of aluminum alloy 5083-O. Adv. Struct. Mater2018; 72: 11–25.
21.
GrujicicMHeTArakereG, et al.Fully coupled thermomechanical finite element analysis of material evolution during friction-stir welding of AA5083. Proc. Inst Mech. Eng. Part B J. Eng. Manuf2010; 224: 609–625.
22.
KimDBadarinarayanHKimJH, et al.Numerical simulation of friction stir butt welding process for AA5083-H18 sheets. Eur. J. Mech. A/Solids2010; 29: 204–215.
23.
JainVKSMuthukumaranS. Influence of SiC content on microstructure and tribological properties of friction stir-processed SiC/AA5083 surface composites. Metall. Mater. Trans. A Phys. Metall. Mater. Sci2019; 50: 2933–2944.
24.
MohajeraniSBordatchevEVTutunea-FatanOR, et al.Thermophysical simulation and experimental verification of remelting lines during laser polishing of H13 tool steel. Lasers Manuf. Mater. Process2020; 7: 317–337.
25.
GadakhVSAdepuK. Heat generation model for taper cylindrical pin profile in FSW. J Mater Res Technol2013; 2: 370–375.
26.
ArafatEAl BadourFMerahN. Fully coupled thermo-mechanical finite element modeling of friction stir processing of super duplex stainless steel. Int. J. Adv. Manuf. Technol2021; 112: 3485–3500.
27.
ZhangZZhangHW. A fully coupled thermo-mechanical model of friction stir welding. Int. J. Adv. Manuf. Technol2008; 37: 279–293.
28.
SchmidtHHattelJ. A local model for the thermomechanical conditions in friction stir welding. Modell. Simul. Mater. Sci. Eng2004; 13: 77–93.
29.
ZhangZLiuYChenJ. Effect of shoulder size on the temperature rise and the material deformation in friction stir welding. Int. J. Adv. Manuf. Technol2009; 45: 889–895.
30.
MeyghaniBWuC. Progress in thermomechanical analysis of friction stir welding. Chinese J. Mech. Eng2020; 33: 1–33.
31.
El-SayedMMShashAYAbd-RabouM. Finite element modeling of aluminum alloy AA5083-O friction stir welding process. J. Mater. Process. Technol2018; 252: 13–24.
32.
DurdanovicMBMijajlovicMMMilcicDS,et al.Heat generation during friction stir welding process. Tribology in industry2009; 31: 8–14.
33.
Kumar SMSankarapandianSShanmugamNS. Investigations on mechanical properties and microstructural examination of activated TIG-welded nuclear grade stainless steel. J. Braz. Soc. Mech. Sci. Eng2020; 42: 292.
34.
DattaSBandyopadhyayAPalPK. Grey-based taguchi method for optimization of bead geometry in submerged arc bead-on-plate welding. Int. J Adv. Manuf. Technol2008; 39: 1136–1143.
35.
BirolYKasmanS. Effect of welding parameters on microstructure and mechanical properties of friction stir welded en AW 5083 H111 plates. Mater. Sci. Technol2013; 29: 1354–1362.
36.
ChoiDHAhnBWQuesnelDJ, et al.Behavior of β phase (Al3Mg2) in AA 5083 during friction stir welding. Intermetallics2013; 35: 120–127.
37.
VermaRPPandeyKN. Fracture behavior of GMA welded joints of dissimilar and similar aluminum alloys of 6061-T6/5083-O. J Fail. Anal. and Preven2017; 17: 248–254.
38.
ChauhanPJainRPalSK, et al.Modeling of defects in friction stir welding using coupled eulerian and lagrangian method. J. Manuf. Process2018; 34: 158–166.
39.
PalSPhanirajMP. Determination of heat partition between tool and workpiece during FSW of SS304 using 3D CFD modeling. J. Mater. Process. Technol2015; 222: 280–286.
40.
PanWLiDTartakovskyAM, et al.A new smoothed particle hydrodynamics non-newtonian model for friction stir welding: process modeling and simulation of microstructure evolution in a magnesium alloy. Int. J. Plast2013; 48: 189–204.
