In this work, the bending fatigue strengths of injection-molded symmetric and asymmetric nylon 66 gears were evaluated experimentally, and the results were substantiated using numerical studies. The symmetric (20°/20°) and asymmetric (34°/20° and 20°/34°) configurations were subjected to bending fatigue tests under a load controlled mode. The bending stresses of the symmetric and asymmetric gears were predicted by quasi-static simulations using a commercial finite element analysis software. The form factor () and the stress correction factor () were computed using an adapted ISO method. The 34°/20° configuration exhibited the lowest bending stress and highest bending fatigue life among the tested configurations. The form factor exerted a decisive influence on the magnitude of the bending stress compared to the stress correction factor. For the considered loading conditions, deflection-induced load sharing occurred in the 20°/20° and 20°/34° configurations but was absent in the 34°/20° configuration. Failure analysis indicated that a high stress concentration caused multiple cracks in the fillets of asymmetric gears.
KarimpourMDearnKDWaltonD. A kinematic analysis of meshing polymer gear teeth. Proc IMechE, Part L: J Materials: Design and Applications2010; 224: 101–115.
10.
HaslCLiuHOsterP, et al.Method for calculating the tooth root stress of plastic spur gears meshing with steel gears under consideration of deflection-induced load sharing. Mech Mach Theory2017; 111: 152–163.
11.
Kapelevich AL and Shekhtman Y V. Rating of asymmetric tooth gears. AGMA Technical Paper, October 2015.
12.
CavdarKKarpatFBabalikFC. Computer aided analysis of bending strength of involute spur gears with asymmetric profile. J Mech Des2005; 127: 477–484.
13.
PedreroJIRuedaAFuentesA. Determination of the ISO tooth form factor for involute spur and helical gears. Mech Mach Theory1999; 34: 89–103.
14.
Prabhu SekarRMuthuveerappanG. Estimation of tooth form factor for normal contact ratio asymmetric spur gear tooth. Mech Mach Theory2015; 90: 187–218.
15.
ThomasBSankaranarayanasamyKRamachandraS, et al.Search method applied for gear tooth bending stress prediction in normal contact ratio asymmetric spur gears. Proc IMechE, Part C: J Mechanical Engineering Science2018; 232: 4647–4663.
16.
MoSMaSJinG. Research on composite bending stress of asymmetric gear in consideration of friction. Proc IMechE, Part C: J Mechanical Engineering Science2019; 233: 2939–2955.
17.
Prabhu SekarR. Determination of load dependent gear loss factor on asymmetric spur gear. Mech Mach Theory2019; 135: 322–335.
Brown FW, Davidson SR, Hanes DB, et al. Analysis and testing of gears with asymmetric involute tooth form and optimized fillet form for potential application in helicopter main drives. AGMA Technical Paper, October 2010.
20.
Sanders A, Houser DR, Kahraman A, et al. An experimental investigation of the effect of tooth asymmetry and tooth root shape on root stresses and single tooth bending fatigue life of gear teeth. In: Proceedings of the ASME 2011 international design engineering technical conferences & computers and information in engineering conference, Washington, USA, 2011.
TavcarJGrkmanGDuhovnikJ. Accelerated lifetime testing of reinforced polymer gears. J Adv Mech Des Syst Manuf2018; 12: 1–13.
23.
ZorkoDKulovecSDuhovnikJ, et al.Durability and design parameters of a Steel/PEEK gear pair. Mech Mach Theory2019; 140: 825–846.
24.
MaoKGreenwoodDRamakrishnanR, et al.The wear resistance improvement of fibre reinforced polymer composite gears. Wear2019; 426–427: 1033–1039.
25.
KumarPKommogiRKSenthilvelanS. Injection molded asymmetric spur gear — development and preliminary performance evaluation. Int J Plast Technol2009; 13: 186–192.
26.
Johnney MertensASenthilvelanS. Durability of injection moulded asymmetric involute polymer spur gears. Int J Powertrains2016; 5: 264–280.
27.
WaltonDTessemaAAHookeCJ, et al.Load sharing in metallic and non-metallic gears. Proc IMechE, Part C: J Mechanical Engineering Science1994; 208: 81–87.
28.
KodeeswaranMVermaASureshR, et al.Effects of frequency on hysteretic heating and fatigue life of unreinforced injection molded polyamide 66 spur gears. Proc IMechE, Part L: J Materials: Design and Applications2019; 233: 781–789.
29.
KalinMKupecA. The dominant effect of temperature on the fatigue behaviour of polymer gears. Wear2017; 376–377: 1339–1346.
30.
MaoKLiWHookeCJ, et al.Friction and wear behaviour of acetal and nylon gears. Wear2009; 267: 639–645.
31.
DüzcükoğluH. Study on development of polyamide gears for improvement of load-carrying capacity. Tribol Int2009; 42: 1146–1153.
32.
Van MelickHGH. Tooth bending effects in plastic spur gears. Gear technology2007, pp. 58–66.
33.
Fuentes A, Gonzalez-perez I, Sanchez-marin FT, et al. On the behavior of asymmetric cylindrical gears in gear transmissions. In: Proceedings of the FISITA 2010 world automotive congress. Berlin, Heidelberg: Springer, 2010, pp.143–149.
34.
AndrewsJD. A finite element analysis of bending stresses induced in external and internal involute spur gears. J Strain Anal Eng Des1991; 26: 153–163.
35.
WaltonDTessemaAAHookeCJ, et al.A note on tip relief and backlash allowances in non-metallic gears. Proc IMechE, Part C: J Mechanical Engineering Science1995; 209: 383–388.
