This study investigated the effectiveness of carbon fibre-reinforced polymer (CFRP) materials in strengthening the diagonal tension members of steel-truss bridges. Monotonic tensile and cyclic loading tests were performed on CFRP-strengthened specimens with variations in the CFRP-bonding range on the flanges. This study focused on the strengthening methods A and B, which were proposed to address insufficient CFRP anchoring near gusset plates by bonding CFRP sheets to both sides of the flanges of the diagonal tension members. The results of the monotonic tensile loading tests indicated a significant increase in tensile stiffness and substantial improvements in yield strength (27%) and ultimate load-bearing capacity (51%) when the strengthening methods A and B were employed. Delamination of the bonded CFRP sheets was effectively delayed, occurring only after the steel yielded, owing to the use of a ductile adhesive (polyurea putty). On the other hand, the cyclic loading tests demonstrated a significant enhancement in the load-bearing capacities (33% for tensile, 32% for compressive) of the strengthened specimens. Moreover, the energy dissipation capacities of the specimens strengthened by methods A and B exhibited linear increases, with 12% and 14% higher values respectively than those of the non-strengthened specimen. Although the stiffnesses (tensile and compressive) of the strengthened specimens decreased in each loading loop, the strengthening methods A and B maintained the stiffness values at approximately 35% higher than those of the non-strengthened specimen.
AbedAAl-MosaweAAl-MahaidiR, et al. (2017) State-of-the-art review on strengthening elements of steel bridges using CFRP. In: Proceedings of the 10th Austroads Bridge Conference, Melbourne, VIC, April 2017, 1–11.
2.
Abu-SenaABBSaidMZakiMA, et al. (2019) Behavior of hollow steel sections strengthened with CFRP. Construction and Building Materials205: 306–320.
3.
AfefyHMSennahKAkhlagh-NejatH (2016) Experimental and analytical investigations on the flexural behavior of CFRP-strengthened composite girders. Journal of Constructional Steel Research120: 94–105.
4.
AguileraJFamA (2013) Retrofitting tubular steel T-joints subjected to axial compression in chord and brace members using bonded FRP plates or through-wall steel bolts. Engineering Structures48: 602–610.
5.
ColombiPBassettiANussbaumerA (2003) Analysis of cracked steel members reinforced by pre‐stress composite patch. Fatigue & Fracture of Engineering Materials & Structures26(1): 59–66.
6.
FengkySYPhanVNNakamotoD, et al. (2022) Enhancing buckling capacity of angle steel using unbonded CFRP laminates processed by Vacuum-assisted Resin Transfer Molding (VaRTM). Structures41: 173–189.
7.
GaoXYBalendraTKohCG (2013) Buckling strength of slender circular tubular steel braces strengthened by CFRP. Engineering Structures46: 547–556.
8.
HattoriMHiroseTOhgakiK, et al. (2018) Experimental study on reinforcement method using CFRP for bending load bearing capacity of doubly symmetric steel plate girder. Steel Construction Engineering25(99): 31–39, [In Japanese].
9.
HidekumaYOhgakiKKikuchiS, et al. (2019) Experimental study on evaluation of load capacity of reinforced steel column with carbon fiber sheet. Journal of Structural Engineering65A: 769–778, [In Japanese].
10.
HollawayL (1993) Polymer Composites for Civil and Structural Engineering. Glasgow, UK: Blackie Academic and Professional Publisher.
11.
JARA (Japan Road Association) (1994) Specification for Highway Bridges, Part-2 Steel Bridges. Tokyo, Japan: Maruzen Publication. [In Japanese].
12.
JARA (Japan Road Association) (1996) Specification for Highway Bridges, Part-5 Seismic Design. Tokyo, Japan: Maruzen Publication. [In Japanese].
13.
JARA (Japan Road Association) (2012) Specification for Highway Bridges, Part-2 Steel Bridges. Tokyo, Japan: Maruzen Publication.
14.
JH (Japan Highway Public Corporation) (1981) Steel Bridge Standard Design. Tokyo, Japan: Japan Highway Public Corporation. [In Japanese].
15.
JH (Japan Highway Public Corporation) (2016) Report for Seismic Retrofitting Works of Bridges in Japan. Tokyo, Japan: Japan Highway Public Corporation. [In Japanese].
16.
JSCE (Japan Society of Civil Engineers) (1995) Hanshin-Awaji Great Earthquake Investigation Emergency Report Meeting Document. Tokyo, Japan: Japan Society of Civil Engineers. [In Japanese].
17.
KaanBNAlemdarFBennettCR, et al. (2012) Fatigue enhancement of welded details in steel bridges using CFRP overlay elements. Journal of Composites for Construction16(2): 138–149.
18.
KumaraguruSAlagusundaramoorthyP (2021) Flexural strengthening of steel beams using pultruded CFRP composite sheets with anchorage mechanisms. Structures33: 1414–1427.
19.
MatsumuraMKitadaTTokubayashiM, et al. (2004) Experimental study on seismic retrofitting of circular steel bridge piers stiffened in circumference direction by CFRP sheets. Doboku Gakkai Ronbunshu2004(766): 17–31, [In Japanese].
20.
McCormickFC (1972) Why not plastic bridges. Journal of the Structural Division98: 1757–1767.
21.
MiyashitaTNagaiM (2010) Stress analysis for steel plate with multilayered CFRP under uni-axial loading. Journal of Japan Society of Civil Engineers66(2): 378–392, [In Japanese].
22.
MiyashitaTWakabayashiDHidekumaY, et al. (2015) Repair for axial member in steel bridge by bonding CFRP sheet through high-elongation and low elastic putty, Journal of Japan Society of Civil Engineers71(5): II_23–II_38. [In Japanese].
23.
NagaiMHidekumaYMiyashitaT, et al. (2012) Bonding characteristics and flexural stiffening effect of CFRP strand sheets bonded to steel beams. Procedia Engineering40: 137–142.
24.
NarmashiriKRamli SulongNJumaatMZ (2012) Failure analysis and structural behaviour of CFRP strengthened steel I-beams. Construction and Building Materials30: 1–9.
25.
NERI (Nippon Expressway Research Institute) (2015) Design and Installation Manual for Upgrading of Steel Structures with the Use of Carbon Fiber Sheets. Tokyo, Japan: NERI.
26.
NhutPVMatsumotoY (2020) Experimental analytical and theoretical investigations of CFRP strengthened thin-walled steel plates under shear loads. Thin-Walled Structures155: 106908.
27.
OkazakiNNakamuraHKishiY, et al. (2017) Experimental study on rehabilitation of buckled circular steel bridge pier by externally bonded carbon fiber sheets. [In Japanese], Journal of Japan Society of Civil Engineers73(5): 52–61.
28.
PhamNVMiyashitaT (2020) Nonlinear stress analysis for CFRP-sheet-bonded steel plates under uniaxial tensile loading. Journal of JSCE8(1): 127–143.
29.
PhamNVMiyashitaTOhgakiK, et al. (2018a) Repair method using CFRP sheet for corroded gusset plate connection in truss bridges. Journal of JSCE6(1): 91–109.
30.
PhamNVMiyashitaTOhgakiK, et al. (2018b) Analytical study on remaining capacity of corroded gusset plate connection in truss bridges. Journal of JSCE6(1): 127–146.
31.
PhamNVMiyashitaTOhgakiK, et al. (2021a) Load-carrying capacity of corroded gusset plate connection and its repair using CFRP sheets. Journal of Structural Engineering147(6): 04021068.
32.
PhamNVMiyashitaTOhgakiK, et al. (2021b) Repair method and finite element analysis for corroded gusset plate connections bonded to CFRP sheets. Journal of Structural Engineering147(1): 04020310.
33.
PhamNVOhgakiKMikiT, et al. (2022) Seismic retrofitting method using CFRP sheets for H-section steel beam with variable cross section. Journal of Structural Engineering148(4): 04022004.
34.
PhamNVOhgakiKHattoriM, et al. (2023) Seismic retrofit of diagonal tension members in steel deck-truss bridges using CFRP sheets. Journal of Composites for Construction27(3): 04023023.
35.
Phan VietNKitanoYMatsumotoY (2020) Experimental investigations of the strengthening effects of CFRP for thin-walled storage tanks under dynamic loads. Applied Sciences10(7): 2521.
36.
SakuraiSOhgakiKMiyashitaT, et al. (2024) Buckling tests on H-section members in coupled buckling area reinforced by CFRP sheets. Japanese Journal of JSCE80(14): 23–14007. [In Japanese].
37.
SelvarajSMadhavanM (2019) Strengthening of laterally restrained steel beams subjected to flexural loading using low-modulus CFRP. Journal of Performance of Constructed Facilities33(3): 04019032.
38.
SilvaMABiscaiaHRibeiroP (2019) On factors affecting CFRP-steel bonded joints. Construction and Building Materials226: 360–375.
39.
TafsirojjamanTUr Rahman DogarALiuY, et al. (2022) Performance and design of steel structures reinforced with FRP composites: a state-of-the-art review. Engineering Failure Analysis138: 106371.
40.
TakamoriAMiyashitaTPhamNV, et al. (2021) CFRP sheet repair for steel girder with corroded damage nearby connections. Journal of Japan Society of Civil Engineers, Ser. A1 (Structural Engineering & Earthquake Engineering (SE/EE))77(1): 165–179.
41.
UedaTDaiJG (2005) FRP composites for infrastructures in Japan: review and outlook, innovation & Sustainability of structures. In: Proceedings of the International Symposium on Innovation & Sustainability of Structures in Civil Engineering, Nanjing, China, 20–22 November 2005, 305–320.
42.
YangYBiscaiaHSilvaMA, et al. (2019) Monotonic and quasi-static cyclic bond response of CFRP-to-steel joints after salt fog exposure. Composites Part B: Engineering168: 532–549.
43.
YasudaTOhgakiKHidekumaY, et al. (2024) Experimental study on reinforcement by lightweight resin mortar and CFRP molding material from under the steel deck slab. Japanese Journal of JSCE80(14): 23–14002. [In Japanese].
44.
YeLPFengPLuXZ, et al. (2004) FRP in China: the state of FRP research, design guidelines and application in construction. In: FRP Composites in Civil Engineering - CICE 2004, London, UK, December 2004, 109–119.
45.
ZengJJGaoWYLiuF (2018) Interfacial behavior and debonding failures of full-scale CFRP-strengthened H-section steel beams. Composite Structures201: 540–552.
ZhaoJFangJYangY, et al. (2023) Experimental study on mixed mode-I & II bond behavior of CFRP-to-steel joints with a ductile adhesive. Thin-Walled Structures184: 110532.
