In this article, Inconel 718 was fabricated on the CuCrZr substrate with cold-sprayed intermediate layer using wire-laser directed energy deposition. The interface microstructure and mechanical properties of IN718/CuCrZr bimetallic structure were examined for both as-deposition and heat treatment conditions. It was found that IN718/CuCrZr interface exhibited sound metallurgical bonding without defects. Fine equiaxed grain zone with the average grain size of 1.3 ± 0.6 μm was observed at as-deposited interface and broadened after heat treatment. Hardness and elongation of the IN718/CuCrZr interface enhanced upon heat treatment. Remelting and rapid solidification of the grain edges near the interface contributed to wider fine grain zone. Precipitation strengthening of Cr phase generated by heat treatment led to the increment of mechanical properties of interface region.
DiaoZYangFwangR, et al.Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing. J Alloys Compd2023; 967: Article 171786.
2.
WangWZhuJQinN, et al.Effects of minor rare earths on the microstructure and properties of Cu-Cr-Zr alloy. J Alloys Compd2020; 847: Article 155762.
3.
LiLWangQWangK, et al.Precipitation behavior of supersaturated solid-solubility CuCrZr alloy by additive manufacturing. Mater Sci Eng A2024; 901: Article 146557.
4.
JiangZYangKXinY, et al.Microstructure, high-temperature oxidation and tribological performance of cold-sprayed CuCrZr coating. Surf Coat Technol2023; 469: Article 129810.
5.
ZhangXLeiQZhangM, et al.Mo2C particle-reinforced CuCrZr composite with enhanced wear and softening resistance. Mater Charact2023; 203: Article 113077.
6.
BambachMSizovaIKiesF, et al.Directed energy deposition of Inconel 718 powder, cold and hot wire using a six-beam direct diode laser set-up. Additive Manufacturing2021; 47: Article 102269.
7.
JeongWLeeTSeong-JuneY, et al.Effect of decomposed TiCp on the mechanical properties of laser powder directed energy depositioned Inconel 718. J Mater Sci Technol2024; 224: 66–79.
8.
LiuKYanZWangF, et al.Microstructure, texture and mechanical properties of Inconel GH4169 superalloy fabricated by wire arc additive manufacturing with arc oscillation. J Alloys Compd2023; 952: Article 170070.
9.
Blakey-MilnerBGradlPSneddenG, et al.Metal additive manufacturing in aerospace: a review. Mater Des2021; 209: Article 110008.
10.
KerstensFCervoneAGradlP. End to end process evaluation for additively manufactured liquid rocket engine thrust chambers. Acta Astronaut2021; 182: 454–465.
11.
GradlPRGreeneSWammenT. Bimetallic channel wall nozzle development and hot-fire testing using additively manufactured laser wire direct closeout technology. In: AIAA Propulsion and Energy 2019 Forum, 2019, pp.4361.
MunroCChenJ. Direct comparison of cold metal transfer to laser hot-wire cladding for AISI 4340 structural steel repair. Sci Technol Weld Joining2021; 26: 11–19.
14.
DebRoyTWeiHLZubackJS, et al.Additive manufacturing of metallic components-process, structure and properties. Prog Mater Sci2018; 92: 112–224.
ShahwazMNathPSenI. Recent advances in additive manufacturing technologies for Ni-based Inconel superalloys-A comprehensive review. J Alloys Compd2025; 1010: 177654.
17.
OnuikeBHeerBBandyopadhyayAJAM. Additive manufacturing of Inconel 718-copper alloy bimetallic structure using laser engineered net shaping (LENS™). Addit Manuf2018; 21: 133–140.
18.
LiuKYanZPanR, et al.Interfacial bonding and microstructural evolution in Inconel-copper bimetallic structures fabricated by directed energy deposition-arc. Mater Sci Eng A2024; 898: Article 146381.
19.
LiuKYanZPanR, et al.Effect of deposition sequence on interfacial characteristics of Inconel-copper functional bimetallic structures fabricated by directed energy deposition-arc. Mater Lett2023; 345: Article 134487.
20.
ChangTFangXZhouY, et al.Heterogeneous interfaces of aluminum bronze/Inconel 718 dissimilar alloys under different wire arc directed energy deposition sequences. Int J Extreme Manuf2025; 7: 015003.
21.
ZhangLDongPZengY, et al.Additive manufacturing of Inconel 718/CuCrZr multi-metallic materials fabricated by laser powder bed fusion. Addit Manuf2024; 92: Article 104377.
22.
HuRLuoMLiuT, et al.Thermal fluid dynamics of liquid bridge transfer in laser wire deposition 3D printing. Sci Technol Weld Joining2019; 24: 401–411.
23.
YanCHanHWangR, et al.Effect of laser oscillation mode on LWAM deposition morphology and melting pool fluctuation. Sci Technol Weld Joining2024; 29: 251–260.
24.
FroendMVentzkeVDornF, et al.Microstructure by design: an approach of grain refinement and isotropy improvement in multi-layer wire-based laser metal deposition. Mater Sci Eng A2020; 772: Article 138635.
25.
JiangMLiBChenX, et al.Enhanced surface finish and reduced porosity of TiC nanoparticles reinforced 2219 aluminum alloy deposit fabricated via oscillating laser-arc hybrid additive manufacturing. J Manuf Process2024; 120: 414–425.
26.
LiBChenXJiangM, et al.Microstructure and mechanical properties of TiC nanoparticles reinforced 7075 aluminium alloy fabricated by oscillating laser-arc hybrid additive manufacturing. Sci Technol Weld Joining2023; 28: 495–505.
27.
KaufmannFMöttingdörferRRothS, et al.Investigation of coupling efficiency in laser beam welding of copper materials using brilliant infrared and green laser radiation. J Manuf Process2024; 131: 2037–2050.
28.
WeiYWenYDuJ, et al.Melt pool behavior of pure copper-stainless steel multi-materials fabricated by the coaxial hybrid blue-infrared lasers additive manufacturing. J Manuf Process2024; 125: 50–63.
29.
ZhangPLiuXYanHJS, et al.Phase composition, microstructure evolution and wear behavior of Ni-Mn-Si coatings on copper by laser cladding. Surf Coat Technol2017; 332: 504–510.
30.
LiuFLiuCChenS, et al.Pulsed Nd: YAG laser post-treatment Ni-based crack-free coating on copper substrate and its wear properties. Surf Coat Technol2007; 201: 6332–6339.
31.
LiuFLiuCChenS, et al.Laser cladding Ni-Co duplex coating on copper substrate. Opt Lasers Eng2010; 48: 792–799.
32.
DiaoZYangFZhangY, et al.Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing. J Alloys Compd2023; 967: Article 171786.
33.
SopousekJVrestalJPinkasJ, et al.Cu-Ni nanoalloy phase diagram-prediction and experiment. Calphad2014; 45: 33–39.
34.
WangZGuanKGaoM, et al.The microstructure and mechanical properties of deposited-IN718 by selective laser melting. J Alloys Compd2012; 513: 518–523.
35.
ParimiLLARGClarkD, et al.Microstructural and texture development in direct laser fabricated IN718. Mater Charact2014; 89: 102–111.
36.
ArrizubietaJIKlockeFKlingbeilN, et al.Evaluation of efficiency and mechanical properties of Inconel 718 components built by wire and powder laser material deposition. Rapid Prototyp J2017; 23: 965–972.
37.
CooperDRAllwoodJM. Influence of diffusion mechanisms in aluminium solid-state welding processes. Procedia Eng2014; 81: 2147–2152.
38.
ChenJBiGZhaoD, et al.Subsequent enhancement of mechanical properties using heat treatment of steel/copper bimetallic structures manufactured by laser powder bed fusion. J Mater Res Technol2024; 33: 8944–8957.
