Wire arc additive manufacturing (WAAM) has emerged as a promising method for additive manufacturing due to its high efficiency and cost-effectiveness. This study aimed to fabricate Co-based Elgiloy by WAAM based on cold metal transfer technology. An 18-layers thin alloy wall was prepared. The microstructure, texture and mechanical properties of the as-deposited samples were investigated. Results indicated that the prepared alloy had good formability and was composed of a single face center cubic structure. The tensile properties of the alloy exhibited anisotropy due to the large number of columnar grains growing along the building direction in the alloy. The tensile samples along the building direction exhibited lower yield strength but better elongation due to the columnar grain growth direction and the softening effect of the remelted zone.
XiaoWCLiuSFZhaoYL, et al.A novel single-crystal L12-strengthened Co-rich high-entropy alloy with excellent high-temperature strength and antioxidant property. J Mater Res Technol2023; 23: 2343–2350.
2.
WangSYHouXYChengY, et al.Investigation on the solidification behavior in a brazed joint of the γ'-strengthened Co-based single crystal superalloy. Mater Charact2022; 186: 111793.
3.
DingHCaoYHuaK, et al.Fretting wear resistance at ambient and elevated temperatures of 316 stainless steel improved by laser cladding with Co-based alloy/WC/CaF2 composite coating. Opt Laser Technol2023; 163: 109428.
4.
Assefpour-DezfulyMBonfieldW. Strengthening mechanisms in Elgiloy. J Mater Sci1984; 19: 2815–2836.
5.
QureshiINRaniSYasminF,et al.TEM study for strengthening mechanisms in Elgiloy. Key Eng Mater2010; 442: 268–274.
6.
SharmaADixitSBalerN, et al.Impact of boron as an alloying addition on the microstructure, thermo-physical properties and creep resistance of a tungsten-free Co-base γ/γ′ superalloy. Mater Sci Eng A2022; 855: 143899.
7.
JungJChoiMLeeH, et al.Effect of line energy on microstructures and mechanical properties of Co-Cr-Mo alloy single-track fabricated by DED method. J Alloys Compd2023; 946: 169381.
8.
LiuAYinBZhangD,et al.Microstructure, mechanical and electrochemical properties of wire-arc additively manufactured duplex stainless steel. Sci Technol Weld Joint2023; 28: 268–276.
9.
RenBZhangMChenC, et al.Effect of heat treatment on microstructure and mechanical properties of stellite 12 fabricated by Laser additive manufacturing. J Mater Eng Perform2017; 26: 5404–5413.
10.
SantecchiaEGattoABassoliE, et al.Precipitates formation and evolution in a Co-based alloy produced by powder bed fusion. J Alloys Compd2019; 797: 652–658.
11.
YuanQLiuCWangW,et al.Residual stress distribution in a large specimen fabricated by wire-arc additive manufacturing. Sci Technol Weld Joi2023; 28: 137–144.
12.
WuBPanZDingD, et al.A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement. J Mater Process2018; 35: 127–139.
13.
LiZCuiYWangJ, et al.Characterization of microstructure and mechanical properties of stellite 6 part fabricated by wire arc additive manufacturing. Metals2019; 9: 74.
14.
RajeevGPRahulMRKamarajM,et al.Microstructure and high temperature mechanical properties of wire arc additively deposited Stellite 6 alloy. Materialia2020; 12: 100724.
15.
ToozandehjaniMOstovanFShamshirsazM. Twin hot-wire arc welding additive manufacturing deposition of high tungsten Stellite-6 hard-facing coating: processing, microstructure and wear properties. Mater Today Commun2023; 35: 105572.
16.
KindermannRMRoyMJMoranaR,et al.Process response of Inconel 718 to wire + arc additive manufacturing with cold metal transfer. Mater Des2020; 195: 109031.
17.
VoraJParmarHChaudhariR, et al.Experimental investigations on mechanical properties of multi-layered structure fabricated by GMAW-based WAAM of SS316L. J Mater Res Technol2022; 20: 2748–2757.
18.
KarmuhilanMKumananS. Location-dependent microstructure analysis and mechanical behavior of inconel 625 using Cold Metal Transfer(CMT) based wire and arc additive manufacturing. Vacuum2023; 207: 111682.
19.
NiuZWangYGengC, et al.Microstructural evolution, mechanical and corrosion behaviors of as-annealed CoCrFeNiMo (x = 0, 0.2, 0.5, 0.8, 1) high entropy alloys. J Alloys Compd2020; 820: 153273.
20.
ShenQXueJZhengZ, et al.Effect of heat treatment on microstructure and mechanical properties of Al1.2CoCrFeNi2.1 high-entropy alloy fabricated by powder plasma arc additive manufacturing. Mater Sci Eng A2022; 857: 144129.
21.
CagiriciMWangPNgFL, et al.Additive manufacturing of high-entropy alloys by thermophysical calculations and in situ alloying. J Mater Sci Technol2021; 94: 53–66.
22.
ZhangCGaoMZengX. Workpiece vibration augmented wire arc additive manufacturing of high strength aluminum alloy. J Mater Process Technol2019; 271: 85–92.
23.
HönnigeJSeowCEGangulyS, et al.Study of residual stress and microstructural evolution in as-deposited and inter-pass rolled wire plus arc additively manufactured Inconel 718 alloy after ageing treatment. Mater Sci Eng A2021; 801: 140368.
24.
ZhangLQiLDengS, et al.Analyses of anodically formed passive film and corrosion behavior of wire-arc additive manufactured ATI 718Plus® superalloy. Addit Manuf2021; 48: 102443.
25.
WangJPanZCarpenterK, et al.Comparative study on crystallographic orientation, precipitation, phase transformation and mechanical response of Ni-rich NiTi alloy fabricated by WAAM at elevated substrate heating temperatures. Mater Sci Eng A2021; 800: 140307.
26.
ShiXMaSLiuC, et al.Selective laser melting-wire arc additive manufacturing hybrid fabrication of Ti-6Al-4 V alloy: microstructure and mechanical properties. Mater Sci Eng A2017; 684: 196–204.
27.
ZhouSZhangJYangG, et al.Microstructure evolution and fracture behavior of Ti–6Al–4 V fabricated by WAAM-LDM additive manufacturing. J Mater Res Technol2024; 28: 347–362.
28.
KleinTSchnallMGomesB, et al.Wire-arc additive manufacturing of a novel high-performance Al-Zn-Mg-Cu alloy: processing, characterization and feasibility demonstration. Addit Manuf2021; 37: 101663.
29.
QiZQiBCongB, et al.Microstructure and mechanical properties of wire + arc additively manufactured 2024 aluminum alloy components: as-deposited and post heat-treated. J Mater Process2019; 40: 27–36.
30.
HePWeiZWangY, et al.A novel droplet + arc additive manufacturing for aluminum alloy: method, microstructure and mechanical properties. Addit Manuf2023; 61: 103356.
31.
SunLJiangFHuangR, et al.Anisotropic mechanical properties and deformation behavior of low-carbon high-strength steel component fabricated by wire and arc additive manufacturing. Mater Sci Eng A2020; 787: 139514.
32.
HeJYWangHHuangHL, et al.A precipitation-hardened high-entropy alloy with outstanding tensile properties. Acta Mater2016; 102: 187–196.
33.
LiWHuangYXieZ, et al.Mechanical property and cellular structure of an additive manufactured FeCoNiCrMo0.2 high-entropy alloy at high-velocity deformation. J Mater Sci Technol2023; 139: 156–166.
34.
LiWLongXHuangS, et al.Elevated fatigue crack growth resistance of Mo alloyed CoCrFeNi high entropy alloys. Eng Fract Mech2019; 218: 106579.
35.
ChenXWangQLiangY, et al.CoCrFeNiMo0.2 high entropy alloy with excellent mechanical properties and corrosion resistance prepared by laser-powder bed fusion. Intermetallics2023; 163: 108082.
36.
ZhaoYLauKBTehWH, et al.Compositionally graded CoCrFeNiTi high-entropy alloys manufactured by laser powder bed fusion: a combinatorial assessment. J Alloys Compd2021; 883: 160825.
37.
DuanHLiuBFuA, et al.Segregation enabled outstanding combination of mechanical and corrosion properties in a FeCrNi medium entropy alloy manufactured by selective laser melting. J Mater Sci Technol2022; 99: 207–214.
38.
ChenFLiuFTanY-B, et al.Achieving excellent strength-ductility synergy via high density dislocation and nano-twinning in cryo-rolled FeCoCrNiMo0.2 high-entropy alloy. J Mater Res Technol2023; 26: 2495–2507.
