A hardening of high velocity oxy-fuel sprayed Inconel 625 coating systems was performed by pulsed plasma nitriding treatment. After deposition of an Inconel 625 coating, samples were pulsed plasma nitrided at 520 °C for 12 h in a gas ratio of 3:1 N2 and H2 under a constant pressure of 2.5 × 102 Pa. Pulsed plasma nitriding improved the microhardness of the high velocity oxy-fuel sprayed Inconel 625 coating from 355 to 401 HV0.05. The high velocity oxy-fuel-sprayed Inconel 625 coating after pulsed plasma nitriding process showed excellent corrosion resistance as well as a reduction of both the friction coefficient and wear rate during the sliding phase in a 3.5 wt.% NaCl solution against sliding action of Al2O3 ball.
BolelliGLusvarghiLGiovanardiR. A comparison between the corrosion resistances of some HVOF-sprayed metal alloy coatings. Surf Coat Tech2008; 202: 4793–4809.
2.
FantozziDMatikainenVUusitaloM,et al.Chlorine-induced high temperature corrosion of Inconel 625 sprayed coatings deposited with different thermal spray techniques. Surf Coat Tech2017; 318: 233–243.
3.
ChenTCChouCCYungTY,et al.A comparative study on the tribological behavior of various thermally sprayed Inconel 625 coatings in a saline solution and deionized water. Surf Coat Tech2020; 385.
4.
OladijoOPCollieusLLObadeleBA,et al.Correlation between residual stresses and the tribological behaviour of Inconel 625 coatings. Surf Coat Tech2021; 419. doi:10.1016/j.surfcoat.2021.127288
5.
BoudiAHashmiMSJYilbasBS. Tensile properties of HVOF sprayed Inconel 625 coatings subjected aqueous corrosion. Ind Lubr Tribol2006; 58: 45–49.
6.
GoyalDKSinghHKumarH. An overview of slurry erosion control by the application of high velocity oxy fuel sprayed coatings. P I Mech Eng J-J-Eng2011; 225: 1092–1105.
7.
GhadamiFAghdamASR. Improvement of high velocity oxy-fuel spray coatings by thermal post treatments: a critical review. Thin Solid Films2019; 678: 42–52.
LiuZCabreroJNiangS,et al.Improving corrosion and wear performance of HVOF-sprayed inconel 625 and WC-Inconel 625 coatings by high power diode laser treatments. Surf Coat Tech2007; 201: 7149–7158.
10.
MindivanFMindivanH. Surface properties and tribocorrosion behaviour of a thermal sprayed martensitic stainless steel coating after pulsed plasma nitriding process. Adv Mat Proc Tech2016; 2: 514–526.
11.
MindivanH. Investigating tribological characteristics of HVOF sprayed AISI 316 stainless steel coating by pulsed plasma nitriding. Iop Conf Series: Mater Sci Eng2018; 295: 1–7.
12.
MusilJVlcekJRuzickaM. Recent progress in plasma nitriding. Vacuum2000; 59: 940–951.
13.
BorowskiTBrojanowskaAKostM,et al.Modifying the properties of the Inconel 625 nickel alloy by glow discharge assisted nitriding. Vacuum2009; 83:1489–1493.
14.
PodgornikBVizintinJLeskovsekV. Tribological properties of plasma and pulse plasma nitrided AISI 4140 steel. Surf Coat Tech1998; 108–109: 454–460.
15.
PodgornikBVizintinJ. Wear resistance of pulse plasma nitrided AISI 4140 and A355 steels. Mat Sci Eng A2001; 315: 28–34.
16.
VarelaLBOrdoñez MF. C.PinedoCE,et al.Micro-abrasive wear study of a low-temperature plasma nitrided Inconel 625 superalloy. Tribol – Mater Surf Interfaces2021.
17.
PonthiauxPWengerFDreesD,et al.Electrochemical techniques for studying tribocorrosion processes. Wear2004; 256: 459–468.
18.
PapageorgiouNBoninAVEspallargasN. Tribocorrosion mechanisms of NiCrMo-625 alloy: an electrochemical modeling approach. Tribol Int2014; 73: 177–186.
19.
ParkGBaeGMoonK,et al.Effect of plasma nitriding and nitrocarburizing on HVOF-sprayed stainless steel coatings. J Therm Spray Techn2013; 22: 1366–1373.
20.
EspallargasNMischlerS. Dry wear and tribocorrosion mechanisms of pulsed plasma nitrided Ni–Cr alloy. Wear2011; 270:464–471.
21.
ZhangYWangQChenG,et al.Mechanical, tribological and corrosion physiognomies of CNT-Al metal matrix composite (MMC) coatings deposited by cold gas dynamic spray (CGDS) process. Surf Coat Tech2020; 403.
22.
BoztepeEAlvesACArizaE,et al.A comparative investigation of the corrosion and tribocorrosion behaviour of nitrocarburized, gas nitrided, fluidized-bed nitrided, and plasma nitride plastic mould steel. Surf Coat Tech2018; 334: 116–123.
23.
NevilleAHodgkiessT. Towards novel ceramic base coatings for corrosive wear applications. Brit Corros J1999; 34: 262–266.
24.
TotolinVPejakovićVCsanyiT, et al.Surface engineering of Ti6Al4 V surfaces for enhanced tribocorrosion performance in artificial seawater. Mater Design2016; 104: 10–18.
