The effect of the apex angle of triangular oil pockets created on a disc surface on friction was studied. Experiments were carried out using an Optimol SRV5 tribotester equipped with a pin-on-disc module under unidirectional lubricated sliding. Both the sample and counter sample was made of steel of 45 Hardness Rockwell C (HRC) hardness. Only 1 ml of oil was put to the inlet side of the contact area at the beginning of each test. All textured surfaces had the same pit-area ratio and an average depth of dimples. Oil pockets were positioned in the spiral array. It was found that the effect of the apex angle of triangular dimples on friction reduction was important. When the normal load was lower, the smallest coefficient of friction was achieved for the sliding pair with a disc apex angle of 60°. Under a larger normal load, a higher apex angle corresponded to a higher coefficient of friction.
EtsionI. State of the art in laser surface texturing. ASME J Tribol2005; 125: 248–253.
2.
GachotCRosenkranzAHsuSM,et al.A critical assessment of surface texturing for friction and wear improvement. Wear2017; 372–373: 21–41.
3.
RosenkranzAGrützmacherPGachotC,et al.Surface texturing in machine elements—A critical discussion for rolling and sliding contacts. Adv Eng Mater2019; 21: 1900194.
4.
QiuMDeliARaeymaekersB. The effect of texture shape on the load-carrying capacity of gas-lubricated parallel slider bearings. Tribol Lett2012; 48: 315–327.
5.
YuHWangXZhouF. Geometric shape effects of surface texture on the generation of hydrodynamic pressure between conformal contacting surfaces. Tribol Lett2010; 37: 123–130.
6.
ZhangYZhangXMatsoukasG. Numerical study of surface texturing for improving tribological properties of ultra-high molecular weight polyethylene. Biosurf Biotribol2015; 1: 270–277.
7.
ShenCKhonsariM. Numerical optimization of texture shape for parallel surfaces under unidirectional and bidirectional sliding. Tribol Int2015; 82: 1–11.
8.
WangXShiLDaiQ,et al.Multi-objective optimization of dimple shapes for gas face seals. Tribol Int2018; 123: 216–223.
9.
AdjemoutMBrunetiereNBouyerJ. Numerical analysis of the texture effect on the hydrodynamic performance of a mechanical seal. Surf Topogr Metrology Prop2016; 4: 014002.
10.
AdjemoutMBrunetiereNBouyerJ. Optimization of mesh density for numerical simulations of hydrodynamic lubrication considering textured surfaces. Proc Inst Mech Eng Part J-J Eng Tribol2015; 229: 1132–1144.
11.
AdjemoutMAndrieuxABouyerJ,et al.Influence of the real dimple shape on the performance of a textured mechanical seal. Tribol Int2017; 115: 409–416.
12.
WeiYTomkowskiRArchentiA. Numerical study of the influence of geometric features of dimple texture on hydrodynamic pressure generation. Metals (Basel)2020; 10: 361.
13.
UddinMLiuY. Design and optimization of a new geometric texture shape for the enhancement of hydrodynamic lubrication performance of parallel slider surfaces. Biosurf Biotribol2016; 2: 59–69.
14.
ZhangHHuaMDongG,et al.A mixed lubrication model for studying tribological behaviors of surface texturing. Tribol Int2016; 93: 583–592.
15.
UddinMIbatanTShankarS. Influence of surface texture shape, geometry and orientation on hydrodynamic lubrication performance of plane-to-plane slider surfaces. Lubr Sci2017; 29: 153–181.
16.
MaCZhuH. An optimum design model for textured surface with elliptical-shape dimples under hydrodynamic lubrication. Tribol Int2011; 44: 987–995.
17.
ShenCKhonsariM. Texture shape optimization for seal-like parallel surfaces: theory and experiment. Tribol T2016; 59: 698–706.
18.
SharmaSJamwalGAwasthiR. Enhancement of steady state performance of hydrodynamic journal bearing using chevron-shaped surface texture. Proc Inst Mech Eng Part J-J Eng Tribol2019; 233: 1833–1843.
19.
JamwalGSharmaSAwasthiR. The dynamic performance analysis of chevron shape textured hydrodynamic bearings. Ind Lubr Tribol2019; 72: 1–8.
20.
MorrisNRahmaniRRahnejatH,et al.A numerical model to study the role of surface textures at top dead center reversal in the piston ring to cylinder liner contact. J Tribol2016; 138: 021703.
21.
RahmaniRShirvaniAShirvaniH. Optimization of partially textured parallel thrust bearings with square-shaped micro-dimples. Tribol T2007; 50: 401–406.
22.
QiangLWangYZhangS,et al.Optimal design of parallel sliders with square-shaped textures considering fluid-structure interaction. Ind Lubr Tribol2019; 71: 620–627.
23.
ZhangHHuaMDongG,et al.Optimization of texture shape based on genetic algorithm under unidirectional sliding. Tribol Int2017; 115: 222–232.
24.
LuPWoodRGeeM,et al.The friction reducing effect of square-shaped surface textures under lubricated line-contacts—An experimental study. Lubricants2016; 4: 26.
LuPWoodRGeeM,et al.The use of anisotropic texturing for control of directional friction. Tribol Int2017; 113: 169–181.
27.
WośSKoszelaWPawlusP. The effect of oil pockets shape on the friction force. Tribologia2018; 4: 151–156.
28.
ChenPXiangXShaoT,et al.Effect of triangular texture on the tribological performance of die steel with TiN coatings under lubricated sliding condition. Appl Surf Sci2016; 389: 361–368.
29.
WangWHuangZShenD,et al.The effect of triangle-shaped surface textures on the performance of the lubricated point-contacts. J Tribol2013; 135: 021503.
30.
GaldaLDzierwaASepJ,et al.The effect of oil pockets shape and distribution on seizure resistance in lubricated sliding. Tribol Lett2010; 37: 301–311.
31.
VladescuSOlverAPeggG,et al.The effects of surface texture in reciprocating contacts—An experimental study. Tribol Int2015; 82: 28–42.
32.
LuXKhonsariM. An experimental investigation of dimple effect on the stribeck curve of journal bearings. Tribol Lett2007; 27: 169–176.
33.
XuYZhengQAbuflahaR,et al.Influence of dimple shape on tribofilm formation and tribological properties of textured surfaces under full and starved lubrication. Tribol Int2019; 136: 267–275.
34.
YuanSHuangWWangX. Orientation effects of micro-grooves on sliding surfaces. Tribol Int2011; 44: 1047–1054.
35.
YuHDengHHuangW,et al.The effect of dimple shapes on friction of parallel surfaces. Proc Inst Mech Eng Part J-J Eng Tribol2011; 225: 693–703.
36.
RosenkranzASzurdakAGrützmacherPG,et al.Friction reduction induced by elliptical surface patterns under lubricated conditions. Adv Eng Mater2017; 20: 1700731.
37.
GrabonWPawlusPWosS,et al.Effects of honed cylinder liner surface texture on tribological properties of piston ring-liner assembly in short time tests. Tribol Int2017; 113: 137–148.
38.
CostaHHutchingsI. Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions. Tribol Int2007; 40: 1227–1238.
39.
WośSKoszelaWPawlusP. Comparing tribological effects of various chevron-based surface textures under lubricated unidirectional sliding. Tribol Int2020; 146: 106205.
40.
RosenkranzACostaHLProfitoF,et al.Influence of surface texturing on hydrodynamic friction in plane converging bearings—An experimental and numerical approach. Tribol Int2019; 134: 190–204.
41.
PawlusPChetwyndD. Efficient characterization of surface topography in cylinder bores. Precis Eng1996; 19: 164–174.
42.
KoszelaWGaldaLDzierwaA,et al.The effect of surface texturing on seizure resistance of a steel-bronze assembly. Tribol Int2010; 43: 1933–1942.
43.
WosSKoszelaWPawlusP. Determination of oil demand for textured surfaces under conformal contact conditions. Tribol Int2016; 93: 602–613.
44.
WosSKoszelaWPawlusP. The effect of both surfaces textured on improvement of tribological properties of sliding elements. Tribol Int2017; 113: 137–148.
45.
HaldarBGharaTAnsariR,et al.Abrasive jet system and its various applications in abrasive jet machining, erosion testing, shot-peening, and fast cleaning. Mater Today Proc2018; 5: 13061–13068.
46.
ChenXQuNFangX,et al.Reduction of undercutting in electrochemical micro-machining of micro-dimple arrays by utilizing oxygen produced at the anode. Surf Coat Technol2015; 277: 44–51.
47.
PetterssonUJacobsonS. Influence of surface texture on boundary lubricated sliding contacts. Tribol Int2003; 36: 857–864
48.
XuYYuJGengJ,et al.Characterization of the tribological behavior of the textured steel surfaces fabricated by photolithographic etching. Tribol Lett2018; 66: 55. https://doi.org/10.1007/s11249-018-1003-4
49.
BhaumikSChowdhuryDBathamA,et al.Analysing the frictional properties of micro dimpled surface created by milling machine under lubricated condition. Tribol Int2020; 146: 106260. https://doi.org/10.1016/j.triboint.2020.106260
