Three-dimensional thermohydrodynamic investigation on the micro-groove textures in the main bearing of internal combustion engine for tribological performances

Abstract

A three-dimensional thermohydrodynamic numerical simulation study was used to investigate the impact of the micro-groove surface texturing on the tribological performances in the main bearing of the internal combustion engine. For this purpose, various number of grooves and groove height to the bearing surface were applied to determine the optimal texture surface parameters by comparing the load-carrying capacity and friction force in the engine main bearing. In the multiphysics numerical model, the three-dimensional Navier–Stokes equation was employed considering the cavitation mechanism based on the Elrod method in the solution. Using the transverse grooves on the bearing surface altered the cavitation response and film reformation. To validate the use of the current numerical model for analyzing the bearings, the obtained results were compared with those of the published theoretical papers, where a good agreement was obtained. The bearing performance was studied in thermal interface conditions to find the optimal set textures parameters that gave minimum fiction force with minimum loss in load-carrying capacity. The bearing with the optimal micro-groove texture parameter showed a reduction in friction (around 16%) with the minimum reduction in load-carrying capacity (around 6%) and the maximum reduction of the flow work (around 15%) compared with the untextured bearing surface. This paper focuses on the thermohydrodynamic investigation with a combination of thermal effects of the fluid film in the textured bearing. Meanwhile, the heat transfer characteristic, temperature distribution of solid bodies, and convection heat transfer coefficient in the contact surfaces of the textured bearing were investigated. The proposed multiphysics numerical model can be widely used for predicting the optimal texture surface parameters in different engineering systems modeling. Moreover, using the three-dimensional-based numerical model is more cost-effective compared with the experimental evaluation of the textured surface.

Keywords

Journal bearing thermohydrodynamic surface texturing multiphysics

Get full access to this article

View all access options for this article.

References

Mufti

Priest

. Theoretical and experimental evaluation of engine bearing performance. Proc IMechE, Part J: J Engineering Tribology 2009; 223: 629–644.

Wakuda

, et al. Effect of surface texturing on friction reduction between ceramic and steel materials under lubricated sliding contact. Wear 2003; 254: 356–363.

Priest

Taylor

. Automobile engine tribology—approaching the surface. Wear 2000; 241: 193–203.

Wang

, et al. The effect of laser texturing of SiC surface on the critical load for the transition of water lubrication mode from hydrodynamic to mixed. Tribol Int 2001; 34: 703–711.

Blatter

, et al. Lubricated sliding performance of laser-patterned sapphire. Wear 1999; 232: 226–230.

Wang

Kato

. Improving the anti-seizure ability of SiC seal in water with RIE texturing. Tribol Lett 2003; 14: 275–280.

Wang

, et al. Loads carrying capacity map for the surface texture design of SiC thrust bearing sliding in water. Tribol Int 2003; 36: 189–197.

Bolander NW, Sadeghi F and Gerber GR. Piston ring friction reduction through surface modification. In: ASME 2005 internal combustion engine division fall technical conference, 2005. American Society of Mechanical Engineers Digital Collection.

Kligerman

Etsion

Shinkarenko

. Improving tribological performance of piston rings by partial surface texturing. J Tribol 2005; 127: 632–638.

10.

Yuan

Huang

Wang

. Orientation effects of micro-grooves on sliding surfaces. Tribol Int 2011; 44: 1047–1054.

11.

Willis

. Surface finish in relation to cylinder liners. Wear 1986; 109: 351–366.

12.

Etsion I. Increasing mechanical seal life with laser-textured seal faces. In: Proceedings of the 15th international conference on fluid sealing, BHR Group, Maastricht, The Netherlands, 1997.

13.

Talke

. Numerical simulation of the head/disk interface for bit patterned media. IEEE Trans Magn 2009; 45: 4984–4989.

14.

Etsion

Kligerman

Halperin

. Analytical and experimental investigation of laser-textured mechanical seal faces. Tribol Trans 1999; 42: 511–516.

15.

Pascovici

, et al. Analytical investigation of a partially textured parallel slider. Proc IMechE, Part J: J Engineering Tribology 2009; 223: 151–158.

16.

Khonsari

. An experimental investigation of dimple effect on the Stribeck curve of journal bearings. Tribol Lett 2007; 27: 169.

17.

Oliveira

Bottene

Franca

. A novel dressing technique for texturing of ground surfaces. CIRP Ann 2010; 59: 361–364.

18.

Etsion

. State of the art in laser surface texturing. J Tribol 2005; 127: 248–253.

19.

Ramesh

, et al. Friction characteristics of microtextured surfaces under mixed and hydrodynamic lubrication. Tribol Int 2013; 57: 170–176.

20.

Morris

, et al. Combined numerical and experimental investigation of the micro-hydrodynamics of chevron-based textured patterns influencing conjunctional friction of sliding contacts. Proc IMechE, Part J: J Engineering Tribology 2015; 229: 316–335.

21.

Has C. The lubrication of rough surfaces. In: Proceedings of the 11th Leeds–Lyon symposium on tribology, 1984. England: The University of Leeds.

22.

Siripuram

Stephens

. Effect of deterministic asperity geometry on hydrodynamic lubrication. J Tribol 2004; 126: 527–534.

23.

Brizmer

Kligerman

Etsion

. A laser surface textured parallel thrust bearing. Tribol Trans 2003; 46: 397–403.

24.

Qiu

Khonsari

. On the prediction of cavitation in dimples using a mass-conservative algorithm. J Tribol 2009; 131: 041702.

25.

Fowell

, et al. Parametric study of texturing in convergent bearings. Tribol Int 2012; 52: 7–16.

26.

Pettersson

Jacobson

. Friction and wear properties of micro textured DLC coated surfaces in boundary lubricated sliding. Tribol Lett 2004; 17: 553–559.

27.

Arghir

, et al. Theoretical analysis of the incompressible laminar flow in a macro-roughness cell. J Tribol 2003; 125: 309–318.

28.

Sahlin

, et al. Two-dimensional CFD-analysis of micro-patterned surfaces in hydrodynamic lubrication. J Tribol 2005; 127: 96–102.

29.

de Kraker

, et al. A multiscale method modeling surface texture effects. J Tribol 2007; 129: 221–230.

30.

Cupillard S, Cervantes M and Glavatskih S. Pressure build-up mechanism in a textured inlet of a slider bearing. In: Svenska Mekanikdagar 2007, Luleå, Sverige, 13–15 June 2007.

31.

Zhang

, et al. A study on the tribological behavior of surface texturing on babbitt alloy under mixed or starved lubrication. Tribol Lett 2014; 56: 305–315.

32.

Meng

. Study of tribological performances of compound dimples based on diatom shell structures. Int J Surf Sci Eng 2015; 9: 538–560.

33.

Yan

, et al. Significance of dimple parameters on the friction of sliding surfaces investigated by orthogonal experiments. Tribol Trans 2010; 53: 703–712.

34.

Zhang

, et al. A mixed lubrication model for studying tribological behaviors of surface texturing. Tribol Int 2016; 93: 583–592.

35.

Tucker

Keogh

. A generalized computational fluid dynamics approach for journal bearing performance prediction. Int J Multiphase Flow 1996; 1001: 144.

36.

Shahmohamadi

, et al. Big end bearing losses with thermal cavitation flow under cylinder deactivation. Tribol Lett 2015; 57: 2.

37.

, et al. A thermal equilibrium analysis of line contact hydrodynamic lubrication considering the influences of Reynolds number, load and temperature. PloS One 2015; 10: e0134806.

38.

Kozubková

Rautová

Bojko

. Mathematical model of cavitation and modelling of fluid flow in cone. Procedia Eng 2012; 39: 9–18.

39.

Andres LS. Hydrodynamic fluid film bearings and their effect on the stability of rotating machinery. Texas A&M University, College Station, TX, USA, 2006.

40.

Guo

Hirano

Kirk

. Application of CFD analysis for rotating machinery—part I: hydrodynamic, hydrostatic bearings and squeeze film damper. J Eng Gas Turbines Power 2005; 127: 445–451.

41.

Morris

, et al. Combined experimental and multiphase computational fluid dynamics analysis of surface textured journal bearings in mixed regime of lubrication. Lubr Sci 2018; 30: 161–173.

42.

Cupillard S, Cervantes M and Glavatskih S. A CFD study of a finite textured journal bearing. In: IAHR symposium on hydraulic machinery and systems, 27–31 October 2008, Foz Do Iguassu, Brazil.

43.

Usman

Park

. Numerical optimization of surface texture for improved tribological performance of journal bearing at varying operating conditions. Ind Lubr Tribol 2018, pp. 70.

44.

Tang

Liu

. Effect of surface texture on the frictional properties of grease lubricated spherical plain bearings under reciprocating swing conditions. Proc IMechE, Part J: J Engineering Tribology 2017; 231: 125–135.