Sage Journals: Discover world-class research

Abstract

This technical note aims to reduce friction power loss of flywheel energy storage system (FESS) supported by hydrodynamic spiral groove bearing and permanent magnetic bearing (PMB). An approach is proposed to fabricate the spiral groove bearing using polytetrafluoroethylene (PTFE) composite. A test rig is developed to test tribological properties of the spiral groove PTFE bearings. Also, two PTFE composites (C-PTFE: 80 vol.% PTFE filled with 20 vol.% graphite; C-Cu-PTFE 50 vol.% PTFE filled with 20 vol.% graphite and 30 vol.% copper powder) are tested. Results show that the friction power losses of the C-PTFE and C-Cu-PTFE bearings are lower than that of the traditional albronze (CuAl) bearing in the whole speed range. In addition, the spiral groove PTFE bearings show an excellent friction-reducing property under boundary or mixed lubrication condition. Finally, a case study is given to show the spiral groove PTFE bearing is capable of reducing the friction power loss of the FESS.

Keywords

Flywheel energy storage system hydrodynamic spiral groove bearing polytetrafluoroethylene composite friction power loss

Get full access to this article

View all access options for this article.

References

Dai

Shen

Wei

. On the vibration of rotor-bearing system with squeeze film damper in an energy storage flywheel. Int J Mech Sci 2001; 43: 2525–2540.

Wang

Jiang

Shen

. The dynamic analysis of an energy storage flywheel system with hybrid bearing supporting. ASME J Vib Acoust 2009; 131: 051006.

Tang

Dai

Zhang

, et al. Rotor dynamics analysis and experiment study of the flywheel spin test system. J Mech Sci Technol 2012; 26: 2669–2677.

Dong

Dai

. Idling loss of flywheel energy storage system supported by spiral groove cone bearings. Mech Sci Technol 2006; 25: 1434–1437.

Diblikova

Pazderova

Vales

. Synthesis of zinc-polytetrafluorethylene composite coatings based on electroplating. Proc IMechE, Part G: J Aerospace Engineering 2013; 227: 447–454.

Simmons

JEL

Knox

Moss

. The development of PTFE (polytetrafluoroethylene)-faced hydrodynamic thrust bearings for hydrogenerator application in the United Kingdom. Proc IMechE, Part J: J Engineering Tribology 1998; 212: 345–352.

Hope

. Application of PTFE based dry film lubrication to moulded plastic by electrophoretic deposition. Transac IMF 2016; 94: 127–130.

Ünlü

Atik

Köksal

. Tribological properties of polymer-based journal bearings. Mater Des 2009; 30: 2618–2622.

Imrek

Demet

. Experimental investigation of wear behaviors of bronze and carbon-reinforced polytetrafluoroethylene alloy pivot pin bearings. Proc IMechE, Part J: J Engineering Tribology 2014; 228: 1187–1194.

10.

Spikes

. The half-wetted bearing. Part 1: extended reynolds equation. Proc IMechE, Part J: J Engineering Tribology 2003; 217: 1–14.

11.

Spikes

. The half-wetted bearing. Part 2: potential application in low load contacts. Proc IMechE, Part J: J Engineering Tribology 2003; 217: 15–26.

12.

Choo

Glovnea

Forrest

, et al. A low friction bearing based on liquid slip at the wall. ASME J Tribol 2007; 129: 611–620.

13.

Aurelian

Patrick

Mohamed

. Wall slip effects in (elasto) hydrodynamic journal bearings. Tribol Int 2011; 44: 868–877.

14.

Wang

, et al. Study on the influence of critical shear stress on wall slip of spiral oil wedge journal bearing. Proc IMechE, Part J: J Engineering Tribology 2012; 226: 362–376.

15.

Lin

Wei

Zhang

, et al. Effects of the slip surface on the tribological performances of high-speed hybrid journal bearings. Proc IMechE, Part J: J Engineering Tribology 2016; 230: 1149–1156.

Reducing friction power losses of flywheel energy storage systems using PTFE composites: A technical note

Abstract

Keywords

Get full access to this article

References