In this study, the effect of the manufacturing tolerances of the pad thickness or the assembly errors on the characteristics of a five-pad tilting-pad journal bearing is analysed. In fact, the pad thickness errors correspond to a different preload factor or clearance for each pad. A sensitivity analysis was performed for several combinations of pad thickness for both load-on-pad and load-between-pad configurations using a thermo-elasto-hydro-dynamic model. Three cases of thickness variations were studied. The numerical results show that these manufacturing or assembly errors considerably affect on both the static and dynamic behaviours of the bearing.
LundJW. Spring and damping coefficients for tilting pad journal bearing. Trans ASLE1967; 7: 342–352.
2.
Jones GJ and Martin FA. Geometry effects in tilting-pad journal bearings. In: The 33rd annual meeting in Dearborn, Michigan, 17–20 April 1978.
3.
WilkesJCChildsDW. Improving tilting pad journal bearing predictions-part I: model development and impact of rotor excited versus bearing excited impedance coefficients. J Eng Gas Turbines Power2013; 135: 012502.
4.
SimmonsFVarelaACSantosIF, et al.Dynamic characteristics of polymer faced tilting pad journal bearings. Tribol Int2014; 74: 20–27.
5.
HouYLaiTChenS, et al.Numerical analysis on the static performance of tilting pad–journal gas bearing in subsystems. Tribol Int2013; 61: 70–79.
6.
WygantKFlackRBarrettL. Measured performance of tilting-pad journal bearings over a range of preloads – Part I: static operating conditions. Tribol Transact2004; 47: 576–584.
7.
WygantKFlackRBarrettL. Measured performance of tilting-pad journal bearings over a range of preloads – Part II: dynamic operating conditions. Tribol Transact2004; 47: 585–593.
8.
Wang W, Li Q, Gao J, et al. Rotordynamic evaluation of full scale rotor on tilting pad bearings with 0.1 and 0.3 preload. Shock Vibrat 2014. Article ID 314892.
9.
Strzelecki S. Dynamic characteristics of tilting 5-pads journal bearing with asymmetric support of pads. In: Sixth international conference on rotor dynamics (IFToMM), Sydney, Australia, 2002, pp.807–814.
10.
WilkesJCChildsDW. Tilting pad journal bearing – a discussion on stability calculation, frequency dependence, and pad and pivot. J Eng Gas Turbines Power2012; 134: 122508.
11.
Dang PV, Chatterton S, Pennacchi P, et al. Behavior of a tilting–pad journal bearing with different load directions. ASME Paper No. DETC2015-46598, 2–5 August 2015, Boston, USA. DOI: 10.1115/DETC2015-46598.
12.
Dang PV, Chatterton S, Pennacchi P, et al. Behavior of tilting-pad journal bearings with large machining error on pads. ASME Turbo Expo, Paper No. GT GT2016-56674, 13–17 June 2016, Seoul, Korea. DOI: 10.1115/GT2016-56674.
13.
Chatterton S, Pennacchi P, Dang PV, et al. A test rig for evaluating tilting-pad journal bearing characteristics. In: Proceedings of the 9th IFToMM international conference on rotor dynamics, Milan, Italy, 22–25 September, 2014, pp.921–930. DOI: http://dx.doi.org/10.1007/978-3-319-06590-8_75.
14.
Dang PV, Chatterton S, Pennacchi P, et al. An experimental study of nonlinear oil-film forces in a tilting-pad journal bearing. ASME Paper No. DETC2015-46601, 2–5 August, 2015, Boston, USA. DOI: 10.1115/DETC2015-46601.
15.
Chatterton S, Pennacchi P, Dang PV, et al. Identification dynamic force coefficients of a five-pad tilting-pad journal bearing. In: Proceedings of the 9th IFToMM international conference on rotor dynamics, Milan, Italy, 22–25 September 2014, pp.931–941. DOI: http://dx.doi.org/10.1007/ 978-3-319-06590-8_76.
16.
Chatterton S, Dang PV, Pennacchi P, et al. Behaviour of tilting-pad journal bearings in case of large manufacturing errors. In: Proceedings of the first international conference of IFToMM Italy, 2016, pp.221-227, http://dx.doi.org/10.1007/978-3-319-48375-7_24.
17.
DangPVChattertonSPennacchiP, et al.Effect of the load direction on non-nominal five-pad tilting-pad journal bearings. Tribol Int2016; 98: 197–211.
18.
FillonMDmochowskiWDadoucheA. Numerical study of the sensitivity of tilting pad journal bearing performance characteristics to manufacturing tolerances: steady-state analysis. Tribol Trans2007; 50: 387–400.
19.
DmochowskiWDadoucheAFillonM. Numerical study of the sensitivity of tilting pad journal bearing performance characteristics to manufacturing tolerances: dynamic analysis. Tribol Trans2008; 51: 573–580.
20.
Gómez JL, Pineda S and Díaz SE. On the effect of pad clearance and preload manufacturing tolerances on tilting pad bearings rotordynamic coefficients. In: ASME Turbo Expo, San Antonio, Texas, USA, 7 June 2013, Paper No. GT 2013-95214.
21.
Quintini JCR, Pineda S, Matute JA, et al. Determining the effect of bearing clearance and preload uncertainties on tilting pad bearings rotordynamic coefficients. In: ASME Turbo Expo, 2014. Paper No. GT 2014-26773.
22.
SuhJPalazzoloA. Three-dimensional dynamic model of TEHD tilting-pad journal bearing – Part I: theroretical modeling. J Tribol2015, pp. 137, 041703 (11 pages). Paper No: TRIB-14-1107. DOI: 10.1115/1.4030020.
23.
ChattertonSPennacchiPVaniaA. Electrical pitting of tilting-pad thrust bearings: modelling and experimental evidence. Tribol Int2016; 103: 475–486.
24.
San AndrésLTaoYLiY. Tilting pad Journal Bearings: On bridging the hot gap between experimental results and model predictions. J Eng Gas Turbine Power2015; 137: 1–11.
25.
KirkRGReedySW. Evaluation of pivot stiffness for typical tilting-pad journal bearing designs. J Vib Acoust Stress Reliab Des1988; 110: 165–171.
26.
PennacchiPVaniaAChattertonS. Nonlinear effects caused by coupling misalignment in rotors equipped with journal bearings. Mech Syst Sig Process2012; 30: 306–322.
27.
ChattertonSDangPVPennacchiP, et al.Experimental evidence of a two-axial groove hydrodynamic journal bearing under severe operation conditions. Tribol Int2017; 109: 416–427.
28.
Brito FP, Bouyer J, Fillon M, et al. Thermal behavior and performance characteristics of a twin axial groove journal bearing as a function of applied load and rotational speed. In: 5thInternational conference on mechanics and materials in design, University of Porto, Portugal, 24–26 July 2006.
