Fast thermo-elasto-hydrodynamic modeling approach for mixed lubricated journal bearings in internal combustion engines

Abstract

Journal bearings are key components in internal combustion engines. Their reliability, durability, and economy are of highest importance. Especially, the accurate prediction of friction loss power and wear are essential for the development of an engine. For an appropriate representation of the hydrodynamic load-carrying capacity and also the friction behavior, both the dynamics of the contacting components, the shape of the contacting component surfaces, the amount of the available lubricant, and the properties of the lubricant itself are of importance. A Reynolds-averaged equation with laminar flow conditions in combination with an asperity contact model is a typical modeling approach for that purpose. The lubricant properties are in particular influenced by its thermal conditions on one hand. On the other hand, the thermal conditions are influenced by the mixed lubricated contact conditions as well. These interactions require a coupled modeling approach, which combines the component flexibility and its interaction with load-carrying capacity as well as the thermal behavior of the lubricant and the component surfaces. In this work, a thermo-elasto-hydrodynamic contact model is presented, which computes the oil film temperature using a 2D energy equation. The 2D equation is derived from the equivalent 3D energy equation by integration over the clearance gap height. Besides component material properties such as specific heat capacity, density, heat conductivity for lubricant and structures, also heat transfer through mixed lubricated regimes and partly filled clearance gaps, as implied in cavitation regions, are being considered. The presented method is applied for a typical engineering task of a sensitivity analysis for oils with different viscosity index (VI) improvers in a main bearing of a four-cylinder inline diesel engine. The influence of the oil film temperature on the oil film viscosity and therefore on the load-carrying capacity is shown. Furthermore, the simplified 2D approach is compared with a 3D approach both in terms of obtained result data and in terms of elapsed calculation times. The presented results show similar accuracy of the 2D approach with significantly reduced simulation time compared to the equivalent 3D case.

Keywords

Main bearing thermo-elasto-hydrodynamic mixed lubrication Reynolds-averaged equation temperature equation flow factors flexible multibody system

Get full access to this article

View all access options for this article.

References

Bukovinik

Offner

Caika

. Thermo-elasto-hydrodynamic lubrication model for journal bearing including shear rate dependent viscosity. J Lubric Sci 2007; 19(4): 231–245.

Gohar

Rahnejat

. Fundamental of tribology, London: Imperial Collage Press, 2012, second edition.

Parikyan T, Resch T and Priebsch HH. Structured model of crankshaft in the simulation of engine dynamics with AVL-EXCITE. SAE Paper 2001-ICE-435, 2001.

Offner

. Modelling of condensed flexible bodies considering non-linear inertia effects resulting from gross motion. J Multi-body Dyn 2011; 225(3): 204–219.

Offner

. Friction power loss simulation of internal combustion engines considering mixed lubricated radial slider, axial slider and piston to liner contacts. Tribol Trans 2013; 56: 503–515.

Freund NO. A thermo-elasto-hydrodynamic study of journal bearings. PhD Thesis, University of Wollongong, Australia, 1995.

Suganami

Szeri

. A thermohydrodynamic analysis of journal bearings. J Tribol 1979; 101(1): 21–27.

Priebsch H and Krasser J. Simulation of the oil film behaviour in elastic engine bearings considering pressure and temperature dependent oil viscosity. In: Proceedings of the 23rd Leeds-Lyon symposium on tribology-elastohydrodynamics, Tribology and interface engineering series, Leeds, vol. 32, 1996, pp. 651–659.

Drab

Engl

Haslinger

. Dynamic simulation of crankshaft mulitbody systems. J Mulit-body Syst Dyn 2009; 22(2): 133–144.

10.

AVL-EXCITE Theory: AVL-List GmbH, 2014.

11.

Herbst HM. Theoretical modeling of the cylinder lubrication in internal combustion engines and its influence on piston slap induced noise, friction and wear. PhD Thesis, Technical University Graz, Austria, 2007.

12.

Rill

Schaeffer

. Grundlagen der Mehrkörpersimulation, New York: Springer Verlag, 2010.

13.

Patir

Cheng

. An average flow model for determining effects of three dimensional roughness on partial hydrodynamic lubrication. Trans ASME J Lubric Technol 1978; 100(1): 12–17.

14.

Krasser J. Analyse dynamisch belasteter Radiallager. PhD Thesis, Technical University Graz, Austria, 1996.

15.

Offner G, Herbst H, Mahmoud K, et al. Analysis of the lubricant flow in a main bearing shell. In: European conference on tribology (ECOTRIB), Vienna, 2011.

16.

Patir

Cheng

. Application of average flow model to lubrication between rough sliding surfaces. J Lubric Technol 1979; 101(2): 220–229.

17.

Offner G, Herbst H, Kamel M, et al. Analysis of the lubrication flow in a main bearing shell. In Proceedings: Ecotrib 2011, 3rd European conference on tribology, Vienna, 2011, pp. 629–638.

18.

Offner G and Knaus O. A generic friction model for radial slider bearing simulation. In: ÖTG Symposium 2014 - Tribologie in Industrie und Forschung: Werkstoffe, Konstruktion und Technologie, Österreichische Tribologische Gesellschaft, 2014.

19.

Greenwood

Tripp

. The contact of two nominal flat rough surfaces. Proc IMechE: Part C: J Mechanical Engineering Science 1970-1971; 185: 625–633.

20.

Cheng

Arai

. Numerical simulation of piston ring in mixed lubrication - nonaxisymmetrical analysis. J Tribol 1994; 116(3): 470–478.

21.

Jedynak

Gilewicz

. Approximation of the integrals of the Gaussian distribution of asperity heights in the Greenwood-Tripp contact model of two rough surfaces revisited. J Appl Math 2013.

22.

Szeri

. Fluid film lubrication, Cambridge: Cambridge University Press, 1998.

23.

Bonneau

Fatu

Souchet

. Thermo-hydrodynamic lubrication in hydrodynamic bearings, New York: John Wiley & Sons, 2014.

24.

Bergman

Lavine

Incropera

. Fundamentals of heat and mass transfer, New York: John Wiley & Sons, 1981.

25.

Huetz J and Petit JP. Notions de transfer thermique par convection, traite Genie Energetique. Techniques de l'Ingenieur, 1990.

26.

Bonneau

Fatu

Souchet

. Internal combustion engine bearing lubrication in hydrodynamic bearings, New York: John Wiley & Sons, 2014.

27.

Pflaum

Mollenhauer

. Wärmeübertragung in der Verbrennungskraftmaschine, New York: Springer Verlag, 1977.

28.

Bonneau

Fatu

Souchet

. Mixed lubrication in hydrodynamic bearings, New York: John Wiley & Sons, 2014.

29.

ABAQUS. ABAQUS theory manual, 2008.

30.

Walters K, Bates TW, Coy RC, et al. On the importance of non-newtonian effects in journal bearing lubrication: A numerical approach. In: International fall fuels & lubricants meeting & exposition, Tusla, Oklahoma, 1997.