A parametric study of microelastohydrodynamic lubrication contact between rough cylinder and plane lubricated with non-Newtonian power law fluid is carried out. A Gaussian rough surface is considered and modeled using stochastic approach. A theoretical solution of pressure distribution, fluid film thickness, and friction for given speeds, material properties, slide-to-roll ratio, and power law index, is obtained by solution of Reynolds equation using finite element method techniques. An isotropic roughness pattern is considered and results are obtained for wide range of operating parameters. The results indicate that the shear-thickening fluids provide thicker lubricant films as compared to shear-thinning fluids. The minimum fluid film thickness is observed to decrease with an increase of load and it increases with an increase of speed and material parameter. Slide-to-roll ratio has a marginal influence of the minimum film thickness. Under certain operating conditions, softer materials with shear-thickening lubricants yield thicker lubricant films than the harder materials lubricated with shear-thinning fluids. The coefficient of friction too is influenced by the rheology of lubricants with shear-thinning fluids providing larger values of coefficient of friction than the shear-thickening fluids.
HolmesMJAEvansHPSnidleRW. Surface contact in micro-EHL. In: Proceedings of IUTAM symposium on elastohydrodynamics and micro-elastohydrodynamics, Cardiff, 2006, pp. 357–368.
DowsonD. Elastohydrodynamic and micro-elastohydrodynamic lubrication. Wear1995; 190: 125–138.
5.
ShenDSalantRF. A transient mixed lubrication model of a rotary lip seal with a rough shaft. Tribol Trans2006; 49: 621–634.
6.
DowsonDJinZ-M. Micro-elastohydrodynamic lubrication of synovial joints. MEP Ltd1986; 15(2): 63–65.
7.
RenNZhuDChenWW. A three-dimensional deterministic model for rough surface line-contact EHL problems. J Tribol2009; 131: 011501–9.
8.
JiangXChengHSHuaDY. A theoretical analysis of mixed lubrication by macro micro approach: Part I – Results in a Gear surface contact. Tribol Trans2000; 43(4): 689–699.
9.
JinZMDowsonD. A general analytical solution to the problem of microelastohydrodynamic lubrication of low elastic modulus compliant bearing surfaces under line contact conditions. Proc IMechE, Part C: J Mechanical Engineering Science1997; 211: 265–272.
10.
KimTWBhushanBChoYJ. The contact behavior of elastic/plastic non-Gaussian rough surfaces. Tribol Lett2006; 22(1): 1–13.
11.
HuaDYQiuLChengHS. Modeling of lubrication in micro-contact. Tribol Lett1997; 3: 81–86.
12.
KamamotoSSakuragiMFujimotoK. Effect of micro-cavitation on oil film thickness and pressure distributions in micro-EHL line contact. In: Elastohydrodynamics ’961997, pp. 113–124.
13.
TyagiMRSethuramiahA. Asperity level conformity in partial EHL, part I: Its characterization. Wear1996; 197: 89–97.
14.
TyagiMRSethuramiahA. Asperity level conformity in partial EHL Part II – Its influence in lubrication. Wear1996; 197(1–2): 98–104.
15.
LiSKahramanA. A fatigue model for contacts under mixed elastohydrodynamic lubrication condition. Int J Fatigue2011; 33: 427–436.
16.
Holmes MJA, Qiao H, Evans HP, et al. Surface contact and damage in micro-EHL. In: Life cycle tribology, Proceedings of 31st Leeds-Lyon symposium on tribology, Leeds, 2005, pp.605–616. Amsterdam: Elsevier.
17.
EvansHPSnidleRWSharifKJ. Deterministic mixed lubrication modeling using roughness measurements in gear applications. Tribol Int2009; 42: 1406–1417.
18.
RykGKligermanYEtsionI. Experimental investigation of laser surface texturing for reciprocating automotive components. Tribol Trans2002; 45(4): 444–449.
19.
KligermanYEtsionIShinkarenkoA. Improving tribological performance of piston rings by partial surface texturing. Trans ASME2005; 127: 632–638.
20.
WakudaMYamauchiYKanzakiS. Effect of surface texturing on friction reduction between ceramic and steel materials under lubricated sliding contact. Wear2003; 254: 356–363.
21.
KovalchenkoAAjayiOErdemirA. The effect of laser surface texturing on transitions in lubrication regimes during unidirectional sliding contact. Tribol Int2005; 38: 219–225.
22.
Morales-EspejelGEGabelliAIoannidesE. Micro-geometry lubrication and life ratings of rolling bearings. Proc IMechE, Part C: J Mechanical Engineering Science2010; 224: 2610–2626.
23.
WangQJZhuDZhouR. Investigating the effect of surface finish on mixed EHL in rolling and rolling-sliding contacts. Tribol Trans2008; 51: 748–761.
24.
Elcoate CD, Evans HP, Hughes TG, et al. Lubrication at the frontier. In: Proceedings of the 25th Leeds-Lyon symposium on tribology, Lyon, 1999, pp.163–174. Amsterdam: Elsevier.
25.
ChristenH. Stochastic models for hydrodynamic lubrication of rough surfaces. Proc Instn Mech Engrs1969–1970; 184(1/55): 1013–1026.
26.
PatirNChengHS. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication. Trans ASME1978; 100: 12–17.
27.
WangWWongPLZhangZ. Partial EHL analysis of rib-roller end contact in tapered roller bearings. Tribol Int1996; 29(4): 313–321.
28.
PrakashJCzichosH. Influence of surface roughness and its orientation on partial elastohydrodynamic lubrication of rollers. J Lubric Technol1983; 105: 591–597.
29.
MajumdarBCHamrockBJ. Effect of surface roughness on elastohydrodynamic line contact. J Lubric Technol1982; 104: 401–407.
30.
MasjediMKhonsariMM. Film thickness and asperity load formulas for line-contact elastohydrodynamic lubrication with provision for surface roughness. J Tribol2012; 134: 011503–1-10.
31.
TallianTEMcCoolJISibleyLB. Partial elastohydrodynamic lubrication in rolling contact. Proc Instn Mech Engrs1965-1966; 180(3B): 169–186.
32.
SahlinFAlmqvistALarssonR. Rough surface flow factors in full film lubrication based on a homogenization technique. Tribol Int2007; 40: 1025–1034.
33.
ChoYJKimTWKooYP. Effect of Kurtosis on the flow factors using average flow model. JSME Int J Ser C2004; 47(1): 429–434.
34.
Morales-EspejelGE. Flow factors for non-Gaussian roughness in hydrodynamic lubrication: An analytical interpolation. Proc IMechE, Part C: J Mechanical Engineering Science2009; 223: 1–9.
35.
KimTWChoYJ. The flow factors considering the elastic deformation for the rough surface with a non-Gaussian height distribution. Tribol Trans2008; 51: 213–220.
36.
GreenwoodJA. Two-dimensional flow of a non-Newtonian lubricant. Proc IMechE, Part J: J Engineering Tribology2000; 214: 29–41.
37.
ChippaSPSarangiM. Elastohydrodynamically lubricated finite line contact with couple stress fluids. Tribol Int2013; 67: 11–20.
38.
JangJYKhonsariMMBairS. On the elastohydrodynamic analysis of shear-thinning fluids. Proc R Soc A2007; 463: 3271–3290.
39.
PeiranYJiankunS. On the theory of time-dependent micro-TEHL for a non-Newtonian lubricant in line contacts. Lubric Sci1996; 8–3: 297–312.
40.
ElsharkawyAAHolmesMJAEvansHP. Micro-elastohydrodynamic lubrication of coated cylinders using coupled differential deflection method. Proc IMechE, Part J: J Engineering Tribology2006; 220: 29–41.
41.
SinhaPShuklaB. Non-Newtonian Power-law fluid lubrication of lightly loaded cylinders with normal and rolling motion. Wear1983; 89: 313–322.
42.
LinTRLinJF. Compressible elastohydrodynamic lubrication of rolling and sliding contacts with a power law fluid. Wear1991; 142: 315–330.
43.
LinTR. Thermal elastohydrodynamic lubrication of rolling and sliding contacts with a power law fluid. Wear1992; 154: 77–93.
44.
BhattacharjeeRCDasNC. Power law fluid model incorporated into elastohydrodynamic lubrication theory of line contact. Tribol Int1996; 29(5): 405–413.
45.
BohanMFJFoxIJClaypoleTC. Numerical modeling of elastohydrodynamic lubrication in soft contacts using non-Newtonian fluids. Int J Numer Meth Heat Fluid Flow2002; 12(4): 494–511.
46.
ChuHMLiWLChenMD. Elastohydrodynamic lubrication of circular contacts at pure squeeze motion with non-Newtonian lubricants. Tribol Int2006; 39: 897–905.
47.
HymanWA. Rheology of Power law fluids. Ind Eng Chem Fundam1976; 15(3): 215–218.
48.
TeipelI. Discontinuities in boundary layer problems of power law fluids. Mech Res Commun1974; 1: 269–273.
49.
HlavacekM. A central film thickness formula for elastohydrodynamic lubrication of cylinders with soft incompressible coatings and a non-Newtonain piecewise power-law lubricant in steady rolling motion. Wear1997; 205: 20–27.
50.
ChuHMLiWLChangYP. Thin film elastohydrodynamic lubrication – a power-law fluid model. Tribol Int2006; 39: 1474–1481.
51.
KumarPJainSCRayS. Thermal elastohydrodynamic lubrication of rolling/sliding line contacts using a mixture of Newtonian and power law fluids. Proc IMechE, Part J: J Engineering Tribology2008; 222: 35–49.
52.
JinnoOTyagiMRKimuraY. Influence of surface roughness on friction and scuffing behaviour of cast iron under sparse lubrication. Tribol Int1996; 29(2): 129–136.
53.
BaglinKP. Micro-elastohydrodynamic lubrication and its relationship with running-in. Proc IMechE1986; 200: 415–424.
54.
JohnsonKLHigginsonJG. A non-Newtonian effect of sliding in micro-EHL. Wear1988; 128(3): 249–264.
55.
MasenMAVennerCHLugtPM. Effects of surface micro-geometry on the lift-off speed of an EHL contact. Tribol Trans2002; 45(1): 21–30.
56.
MourierLMazuyerDLubrechtAA. Transient increase of film thickness in micro-textured EHL contacts. Tribol Int2006; 39: 1745–1756.
57.
OverAVGuangtengGSpikesHAFilm thickness and pressure in micro-EHD contacts. In: DowsonD (ed). Thinning films and tribological interfaces, New York: Elsevier, 2000, pp. 503–510.
58.
BassaniRCiulliEPiccigalloBTheoretical and experimental results on firction for line line contacts in mixed and elastohydrodynamic lubrication regimes. In: DowsonD (eds). Lubrication at the trontier, New York: Elsevier, 1999, pp. 215–222.
59.
WuSChengHS. A sliding wear model for partial EHL contacts. Trans ASME J Tribol1991; 113: 134–141.
60.
HoupertLGHamrockBJ. A fast approach for calculating film thickness and pressure in elastohydrodynamic lubricated contacts at high loads. ASME J Tribol Trans1986; 108: 411–420.
61.
GreenwoodJATrippJH. The contact of two nominally flat rough surfaces. Proc Instn Mech Engrs1970-1971; 185: 48–71.
62.
HuYChengHSAraiT. Numerical simulation of piston ring in mixed lubrication – A non-axi-symmetrical analysis. ASME J Tribol. 116: 470–478.
63.
DowsonDHigginsonGR. A numerical solution to the elastohydrodynamic problem. J Mech Eng Sci1959; 1: 6–15.
64.
LuHBerzinsMGoodyerCE. Adaptive high-order Discontinuous Galerkin solution of elastohydrodynamic lubrication point contact problems. Adv Eng Softw2012; 45: 313–324.
