The performance of hydrodynamic journal bearings is affected by the conditions under which the lubricant is fed to the bearing gap. Axial grooves are often used and, depending on their location relatively to the load line, they might substantially interfere with the hydrodynamic pressure generation and the thermal behaviour of the bearing. However, many of the existing tools for predicting bearing performance are not able to suitably predict bearing behaviour under varying load angle given the oversimplified way under which they treat lubricant feeding conditions. The present work proposes a detailed thermohydrodynamic approach which realistically incorporates these conditions into the bearing analysis. Special care is put on the mass and energy-conserving models of the ruptured film region and on a detailed treatment of lubricant mixing within the vicinity of grooves. This includes the first full modelling of the effect of negative flow rate in a groove, a phenomenon originally described experimentally in detail by the authors in previous publications, and which happens for a broad range of load/groove angles. An extensive investigation on the influence of loading direction on the performance of twin groove journal bearings has been performed. This parameter is found to affect deeply all major performance parameters due to the interference of groove regions in the hydrodynamic pressure generation and in the flow rates at each groove.
ClaroJCPMirandaAS. Analysis of hydrodynamic journal bearings considering lubricant supply conditions. Proc IMechE Part C: J Mechanical Engineering Science1993; 207: 93–101.
2.
CostaLMirandaASFillonM. An analysis of the influence of oil supply conditions on the thermohydrodynamic performance of a single groove journal bearing. Proc IMechE Part J: J Engineering Tribology2003; 217: 133–144.
3.
BritoFPFillonMMirandaAS. The role of lubricant feeding conditions on the performance improvement and friction reduction of journal bearings. Tribol Int2014; 72: 65–82.
4.
CostaLFillonMMirandaAS. An experimental investigation of the effect of groove location and supply pressure on the THD performance of a steadily loaded journal bearing. ASME J Tribol2003; 122: 227–232.
5.
BritoFPBouyerJFillonM. Experimental investigation of the influence of supply temperature and supply pressure on the performance of a two axial groove hydrodynamic journal bearing. ASME J Tribol2007; 129: 98–105.
6.
Brito FP, Miranda AS, Claro JCP, et al. The role of each groove on the behavior of twin axial groove journal bearings. In: IBERTRIB – Congreso Ibérico de Tribología, Escuela de Ingenieros, Bilbau, 20–21 June 2007, CD-ROM.
7.
BritoFPMirandaASClaroJCP. The role of lubricant supply temperature on the performance of twin groove journal bearings: an experimental study. Int J Surface Sci Eng2011; 5(4): 286–299.
8.
BritoFPMirandaASClaroJCP. Experimental comparison of the performance of a journal bearing with a single and a twin axial groove configuration. Tribol Int2012; 54: 1–8.
9.
Arab SolgharABritoFPClaroJCP. An experimental study of the influence of loading direction on the thermohydrodynamic behavior of twin axial groove journal bearing. Proc IMechE Part J: J Engineering Tribology2011; 225(5): 245–254.
10.
DowsonDTaylorCMMirandaAS. The prediction of liquid film journal bearing performance with a consideration of lubricant film reformation, part I and II. Proc IMechE Part J: J Engineering Tribology1985; 119(C2): 95–102102–111.
11.
BraunMJHannonWM. Cavitation formation and modelling for fluid film bearings: a review. Proc IMechE Part J: J Engineering Tribology2010; 224(9): 839–863.
12.
ChunSLalasD. Parametric study of inlet oil temperature of a half-circumferential grooved journal bearing. STLE Tribol Trans1992; 35: 213–224.
13.
BoncompainRFillonMFrêneJ. Analysis of thermal effects in hydrodynamic bearings. ASME J Tribol1986; 108: 219–224.
14.
KnightJDGhadimiP. Effects of modified effective length models of the rupture zone on the analysis of a fluid journal bearings. STLE Tribol Trans1992; 35: 29–36.
15.
RajalinghamCPrabhuBS. The influence of variation of viscosity with temperature on the steady state characteristics of journal bearings – simple analysis. Tribol Int1987; 20(5): 261–266.
16.
PierreIFillonM. Influence of geometric parameters and operating conditions on the thermohydrodynamic behavior of plain journal bearings. Proc IMechE Part J: J Engineering Tribology2000; 214: 445–457.
17.
EI-DeihiMKIGethinDT. A thermohydrodynamic analysis of a twin axial groove bearing under different loading directions and comparison with experiment. ASME J Tribol1992; 114: 304–310.
18.
TanakaM. Recent thermohydrodynamic analyses and designs of thick-film bearings. Proc IMechE Part J: J Engineering Tribology2000; 214: 107–122.
19.
KhonsariMM. A review of thermal effects in hydrodynamic bearings. Part II. J Bear ASLE Trans1987; 30(1): 26–33.
20.
BasriHNealPB. Oil flow in axial groove journal bearings. In: Proceedings of the seminar on developments in plain bearings for the ’90s, IMechE Tribology Group1990MayLondon: Mechanical Engineering Publications, pp. 11–17.
21.
GethinDTEI-DeihiMKI. Effect of loading direction on the performance of a twin-axial groove cylindrical-bore bearing. Tribol Int1987; 20(4): 179–185.
22.
GethinDTEl-DeihiMKI. Thermal behavior of a twin axial groove bearing under varying loading direction. Proc IMechE Part C: J Mechanical Engineering Science1990; 204: 77–90.
23.
RoyLLahaSK. Steady state and dynamic characteristics of axial grooved journal bearings. Tribol Int2009; 42: 754–761.
BritoFP. Thermohydrodynamic performance of twin groove journal bearings considering realistic lubricant supply conditions: an experimental and theoretical study, Guimarães, Portugal: PhD Thesis, School of Engineering, Universidade do Minho, 2009. http://repositorium.sdum.uminho.pt/handle/1822/9884.
26.
PinkusO. Thermal aspects of fluid film tribology, New York: ASME Press, 1990.
27.
ElrodHG. A cavitation algorithm. ASME J Lubr Technol1981; 103(3): 350–354.
28.
FitzgeraldMKNealPB. Temperature distributions and heat transfer in journal bearings. ASME J Tribol1992; 114: 122–130.
29.
FerronJFrêneJBoncompainR. A study of the thermohydrodynamic performance of a plain journal bearing. Comparison between theory and experiments. ASME J Lubr Technol1983; 105: 422–428.
30.
Pierre I and Fillon M. Validity limit of the two-dimensional thermohydrodynamic analysis of plain journal bearings. In: Proceedings of the international tribology conference, ITC 2000, Nagasaki, Japan, 29 October–2 November 2000, Japanese Society of Tribologists, vol. III, pp.1555–1560.
31.
FrêneJNicolasDDegueurceB. Lubrification hydrodynamique – paliers et butées. Collection de la direction des Études et Recherches d'Électricité de France, Paris: 72, Editions Eyrolles, 1990, pp. 354–358.
32.
HeshmatH. The mechanism of cavitation in hydrodynamic lubrication. Tribol Trans1991; 34(2): 177–186.
33.
KnightJDGhadimiP. Analysis and observation of cavities in a journal bearing considering flow continuity. STLE Tribol Trans2001; 44: 88–96.
34.
KosasihPBTieuAK. An investigation into the thermal mixing in journal bearings. Proc IMechE Part J: J Engineering Tribology2004; 218: 379–389.
35.
JeddiLEl KhlifiMBonneauD. Thermohydrodynamic analysis for a hydrodynamic journal bearing groove. Proc IMechE Part J: J Engineering Tribology2005; 219: 263–274.
36.
DowsonDHudsonJHunterB. An experimental investigation of the thermal equilibrium of steadily loaded journal bearings. Proc IMechE Part B: J Engineering Manufacture1966–67; 101: 70–80.
37.
AndrisanoAO. An experimental investigation on rotating journal surface temperature distribution. ASME J Tribol1988; 110: 638–645.
38.
MaMTTaylorCM. A theoretical and experimental study of thermal effects in a plain circular steadily loaded journal bearing. In: IMechE seminar: plain bearings – energy efficiency and design, mech. engs, London: Publications Ltd, 1992.
39.
JangJYKhonsariMM. Design of bearings on the basis of thermohydrodynamic analysis. Proc IMechE Part J: J Engineering Tribology2004; 218: 355–363.
40.
PierreIBouyerJFillonM. Thermohydrodynamic behavior of misaligned plain journal bearings: theoretical and experimental approaches. Tribol Trans2004; 47(4): 594–604.
41.
Brito FP, Bouyer J, Fillon M, et al. Experimental investigation on the thermal behavior and performance characteristics of a twin axial groove journal bearing as a function of applied load and rotational speed. In: 5th international conference on mechanics & materials in design – M2D’2006, symposium on wear and lubrication in design, FEUP, Porto, 24–26 July 2006. CD-ROM (ISBN 972-8826-10-9).
42.
Engineering Science Data Unit, ESDU. ESDU item no. 84031. Calculation methods for steadily loaded axial groove hydrodynamic journal bearings, London: Engineering Sciences Data Unit (ESDU) International Plc, 1984.
43.
GroperMEtsionI. Reverse flow as a possible mechanism for cavitation pressure build-up in a submerged journal bearing. ASME J Tribol2002; 124: 320–326.
44.
Brito FP, Miranda AS, Claro JCP, et al. On the occurrence of negative groove flow rate in twin groove hydrodynamic journal bearings. In: 15th international conference on experimental mechanics (ICEM15), FEUP, Porto, Portugal, 22–27 July 2012 (extended abstract), pp.875, 876.
