Research is being focused on to find the influence of surface variations such as texturing or grooving on the bearing performances. Though, earlier it was restricted to the theoretical aspects alone, however, with the help of advance manufacturing techniques (laser surface texturing, etching, special grinding process, etc.), it has become possible to produce micro-textures or grooves on the surface of journal bearing. The objective of the present study is to numerically compare the influence of spherical texture and micro-grooving (longitudinal and transverse) on friction coefficient and average temperature of journal bearing at low and high eccentricity ratios. From the findings, it has been observed that the micro-grooving reduces the friction coefficient and average temperature is maximum in comparison with spherical texture.
AdatepeHBiyiklioguiASofuogluH. An experimental investigation on frictional behaviour of statically loaded micro grooved journal bearing. Tribol Int2011; 44: 1942–1948.
7.
SahlinFGlavatskihSAlmqvistT. Two dimensional CFD analysis of micro patterned surfaces in hydrodynamic lubrication. ASME J Tribol2005; 127: 96–102.
8.
FowelMOlverAVGosmanAD. Entrainment and inlet suction: two mechanisms of hydrodynamic lubrication in textured bearings. ASME J Tribol2007; 129: 336–347.
9.
Brajdic-MitidieriPGosmanADIoannidesE. CFD analysis of a low friction pocketed pad bearing. ASME J Tribol2005; 127: 803–812.
10.
CupillardSCervantesMJGlavatskihS. Pressure build up mechanism in a textured inlet of a hydrodynamic contact. ASME J Tribol2008; 130: 021701-1–021701-10.
11.
PapadopoulosCIEfstathiouEENikolakopoulosPG. Geometry optimization of textured three dimensional micro thrust bearing. ASME J Tribol2011; 133: 041702-1–041702-14.
12.
FowellMTMedinaSOlverAV. Parametric study of texturing in convergent bearings. Tribol Int2012; 52: 7–16.
13.
TauviqirrahmanMIsmailRJamariJ. A study of surface texturing and boundary slip improving the load support of lubricated parallel sliding contacts. Acta Mech2013; 224: 365–386.
14.
Tala-IghilNMaspeyrotPFillonM. Effects of surface texture on journal bearing characteristics under steady state operating conditions. Proc IMechE, Part J: J Engineering Tribology2007; 221: 623–633.
15.
Tala-IghilNFillonMMaspeyrotP. Effect of textured area on the performances of a hydrodynamic journal bearing. Tribol Int2011; 44: 211–219.
16.
CupillardSGlavatskihSCervantesMJ. CFD analysis of journal bearing with surface texturing. Proc IMechE, Part J: J Engineering Tribology2008; 222: 97–107.
HuynhBP. Numerical study of slider bearings with limited corrugation. ASME J Tribol2005; 127: 582–595.
20.
FuYJiJBiQ. The influence of partially textured slider with oriented parabolic grooves on the behaviors of hydrodynamic lubrication. Tribol Trans2012; 55: 210–217.
21.
WatanabeKNatsumeJHashizumaK. Theoretical analysis of bearing performance of micro grooved bearing. JSAE Rev2000; 21: 29–33.
22.
AshiharaKHashimotoH. Theoretical modeling for micro grooved journal bearings under mixed lubrication. ASME J Tribol2010; 132: 042101-1–042101-16.
23.
KangoSSinghDSharmaRK. Numerical investigation on the influence of surface texture on the performance of hydrodynamic journal bearing. Meccanica2012; 47: 469–482.
24.
KangoSSharmaRK. Studies on the influence of surface texture on the performance of hydrodynamic journal bearing using power law model. Int J Surf Sci Eng2010; 4: 505–524.
25.
De KrakerAOstryenRAJVan BeekA. A multiscale method modelling surface texture effects. ASME J Tribol2007; 129: 221–230.
26.
AusasRRagotPLeivaJ. The impact of the cavitation model in the analysis of microtextured lubricated journal bearings. ASME J Tribol2007; 129: 868–875.
27.
QiuYKhonsariMM. On the prediction of cavitation in dimples using a mass conservative algorithm. ASME J Tribol2009; 131: 041702-1–041702-11.
28.
ZhangJMengY. Direct observation of cavitation phenomenon and hydrodynamic lubrication analysis of textured surfaces. Tribol Lett2012; 46: 147–158.
29.
WangHYangSGuoF. Modeling of a grooved parallel bearing with a mass conserving cavitation algorithm. Tribol Trans2011; 54: 227–236.
30.
ElrodHG. A cavitation algorithm. ASME J Lubr Technol1981; 103: 350–354.
31.
VijayaraghavanDKeithTG. Development and evaluation of a cavitation algorithm. Tribol Trans1989; 32: 225–233.
32.
FesangharyMKhonsariMM. A modification of the switch function in the Elrod cavitation algorithm. ASME J Tribol2011; 133: 024501-1–024501-4.
33.
JangJYChangCC. Adiabatic analysis of finite width journal bearings with non-newtonian lubricants. Wear1988; 122: 63–75.
34.
ChunSMHaDH. Study on mixing flow effects in a high-speed journal bearing. Tribol Int2001; 34: 397–405.
35.
BoncompainRFillonMFreneJ. Analysis of thermal effects in hydrodynamic bearings. ASME Trans1986; 108: 219–224.
36.
BanwaitSSChandrawatHN. Study of thermal boundary conditions for a plain journal bearing. Tribol Int2001; 31: 289–296.
37.
PinkusOSternlichtB. Theory of hydrodynamic lubrication, New York: McGraw-Hill, 1961.
38.
Cameron AT. The principles of lubrication. New York: Longmans Green & Co Ltd, 1966.
39.
GrandoFPPriestMPrataAT. A two phase flow approach to cavitation modelling in journal bearing. Tribol Lett2006; 21: 233–244.
