An experimental study of the influence of loading direction on the thermohydrodynamic behaviour of twin axial groove journal bearing

Abstract

An experimental assessment of the influence of angle between the groove axis and the load line on the thermohydrodynamic behaviour of twin groove hydrodynamic journal bearings has been undertaken. At nine different loading direction angles, the oil–bush interface temperature profiles, oil outlet temperature, maximum bush temperature, total flow rate, and oil flow rate through each groove were measured for variable applied load and oil supply pressure while the feeding temperature was kept constant (40°C). To the authors’ knowledge, this is the first study of the influence of loading direction on the performance of journal bearing with two axial grooves in which the flow rate were measured in each groove for different working conditions under laminar regime. It was found that the variation of loading direction has a strong effect on the bearing performance. Under some running conditions, negative lubricant flow rate (hot oil reflux) at one groove was detected. This seldom-reported phenomenon was found to affect the bearing performance dramatically. Increasing supply pressure yielded a temperature decrease, especially for high loads, and sometimes prevented the occurrence of hot oil reflux.

Keywords

hydrodynamics lubrication thermal effects experimental results journal bearings

Get full access to this article

View all access options for this article.

References

Mitsui

Hori

Tanaka

–Thermohydrodynamic analysis of cooling effect of supply oil in circular journal bearings. ASME J. Tribol., 1983, 105. 414–421.

Ferron

Frêne

Boncompain

–A study of the thermohydrodynamic performance of a plain journal bearing. Comparison between theory and experiments. ASME J. Tribol., 1983, 105. 422–428.

Syverud

Tanaka

–Experimental investigation of the effect of shaft heating and cooling on single bore journal bearing. Wear, 1997, 207. 112–117.

Tonneson

Hansen

P. K.

–Some experiments on the steady state characteristics of a cylindrical fluid-film bearing considering thermal effects. ASME J. Tribol. Tech., 1981, 103. 107–114.

Gethin

D. T.

El-Deihi

M. K. I.

–Thermal behavior of a twin axial groove bearing under varying loading direction. Proc. IMechE, Part A: J. Power and Energy, 1990, 204. 77–90.

Fitzgerald

M. K.

Neal

P. B.

–Temperature distributions and heat transfer in journal bearings. ASME J. Tribol., 1992, 114. 122–130.

M. T.

Taylor

C. M.

–An experimental investigation of thermal effects in circular and elliptical plain journal bearing. Tribol. Int., 1996, 29(1), 19–26.

Ma, M. T. and Taylor, C. A theoretical and experimental study of thermal effects in a plain circular steadily loaded journal bearing. In Proceedings of the IMechE Seminar on Plain bearings – energy efficiency and design, Institution of Mechanical Engineers, 10 November 1992, pp. 31–44 (Mechanical Engineering Publications Limited, London).

Costa

Fillon

Miranda

A. S.

Claro

J. C. P.

–An experimental investigation of the effect of groove location and supply pressure on the THD performance of a steadily loaded journal bearing. ASME J. Tribol., 2000, 122. 227–232.

10.

Brito

F. P.

Miranda

A. S.

Bouyer

Fillon

–Experimental investigation of the influence of supply temperature and supply pressure on the performance of a two-axial groove hydrodynamic journal bearing. ASME J. Tribol., 2007, 129. 98–105.

11.

Fillon

Bligoud

J. C.

Frene

–Experimental study of tilting-pad journal bearings – comparison with theoretical thermoelastohydrodynamic results. ASME J. Tribol., 1992, 114. 579–588.

12.

Brito, F. P., Miranda, A. S., Claro, J. C. P., and Fillon, M. The role of each groove on the behavior of twin axial groove journal bearings. In Proceedings of the IV Congresso Ibérico de Tribologia (IBERTRIB 2007), Bilbau, Spain, 21–22 June 2007.

13.

Brito, F. P., Miranda, A. S., Claro, J. C. P., and Fillon, M. Experimental study of the influence of groove flow rate on the performance of a single and a twin groove journal bearing. In Proceedings of the STLE Annual Meeting, Cleveland Convention Center, Ohio, 18–22 May 2008.

14.

Claro

J. C. P.

Miranda

A. S.

–Analysis of hydrodynamic journal bearings considering lubricant supply conditions. Proc. IMechE, Part C: J. Mechanical Engineering Science, 1993, 207. 93–101.

15.

Costa

Miranda

A. S.

Claro

J. C. P.

Fillon

–Temperature, flow, and eccentricity measurements in a journal bearing with a single axial groove at 90° to the load line. Lubr. Sci., 2003, 15(2), 147–161.