Sandwich Beam with a Periodical and Graded Core Manufactured Using Rapid Prototyping

Abstract

This article presents a technique for the production of graded sandwich cores, and a study of the effect of lengthwise grading of core properties for the facilitation of transverse loading. A significant failure mode of sandwich panels is caused by indentation of the foam core in regions at which local forces are introduced into the sandwich panel. The aim of this work is to synthesize a microstructure that can diminish this failure mode. By applying a rapid prototyping technique a periodic, open beam structure is synthesized. Additionally, the structure has been graded in the longitudinal direction by alternating over the beam diameter. The structure obtained is joined to aluminium face sheets to form a sandwich beam. The panel has been subjected to a three point bending test and the results have been compared to a finite element model, and further indentation tests show an increased transverse stiffness in the strengthened part of the beam.

Keywords

sandwich panels periodic structure graded material rapid prototyping.

Get full access to this article

View all access options for this article.

References

Zenkert, D. (1997). The Handbook of Sandwich Construction, Chapter 1: Introduction, EMAS Publishing, London.

Skvortsov, V.S. and Thomsen, O.T. (2003). Analytical Estimates for the Stresses in Face Sheets of Sandwich Panels at Junctions between Different Core Materials, In: Proceedings of the 6th International Conference on Sandwich Structures (ICSS-6), CDROM, Fort Lauderdale, FL , USA, pp. 551—559.

Lyckegaard, A. and Thomsen, O.T. (2005). Analysis of Sandwich Beam with Structurally Graded Core for Concentrated Load, In: Verijenko , Adali, Morosov and von Klemperer (eds), Proceedings of the Fifteenth International Conference on Composite Materials (ICCM-15) CDROM, University of KwaZulu Natal , Durban, South Africa.

Apetre, N.A. and Sankar, B.B. (2003). Composite Sandwich Plates with Functionally Graded Cores, In: Proceedings of the 6th International Conference on Sandwich Structures (ICSS-6), Fort Lauderdale, FL, USA, pp. 227—239.

Haydn, N.G.W. , Fleck, N.A. and Evans, A.G. (2003). Fabrication and Structural Performance of Periodic Cellular Metal Sandwich Structures, Composites Science and Technology, 63(16): 2331—2343.

Evans, A.G. (2001). Lightweight Materials and Structures, Materials Research Society Bulletin, 26(10): 23—35.

Chiras, S. , Mumm, D.R. , Evans, A.G. , Wicks, N. , Hutchinson, J.W. , Dharmasena, K. , Wadley, H.N.G. and Fichter, S. (2002). The Structural Performance of Near-optimized Truss Core-panels, International Journal of Solids and Structures , 39(15): 4093—4105.

Bitzer, T. (1997). Sandwich Design, Honeycomb Technology, Chapman and Hall, London, pp. 43—69.

Stratasys (2005). ABS FDM Materials Properties, Stratasys Inc., Eden Prairie, MN, USA, p. 1.

10.

Hendriks, C.L.L. , van Vliet, L.J. , Rieger, B. , van Ginkel, M. and Ligteringen , R. (2002). DIPImage User Manual, Pattern Recognition Group, Faculty of Applied Physics, Delft University of Technology, Delft, pp. 1—50.

11.

Ansys Release 9.0 (2003). Reference Manual, ANSYS Inc., Canonsburg, PA, USA.

12.

Frostig, Y. , Baruch, M. , Vilnay, O. and Sheinman, I. (1992). High Order Theory for Sandwich Beam Bending with Transversely Flexible Core'', Journal of Engineering Mechanics, 118(5): 1026—1043.