High-Order Bending Analysis of Unidirectional Curved ‘‘Soft’’ Sandwich Panels with Disbonds and Slipping Layers

Abstract

The bending behavior of unidirectional singly curved sandwich panels with a ‘‘soft’’ core and delaminated (debonded) zones or slipping layers is described herein. The delaminated zone is assumed to exist through the width of the panels, and is in the form of an interfacial debonded zone at one of the face–core interfaces, thus subdividing the length of the panel into three zones, i.e. two fully bonded zones and one that is debonded (delaminated). The formulation uses an interfacial spring description, i.e. distributed shear and radial normal springs at the face–core interfaces, to model the effects of the slipping layers and the various delaminated (debonded) zones. The formulation is based on a closed-form high-order approach (HSAPT) that incorporates the high-order effects of the ‘‘soft’’ core. The variational approach is used to derive the governing equations along with the general explicit boundary and continuity conditions. A typical curved sandwich panel with an inner or an edge delamination, with or without contact, subjected to a distributed load and pinned supports is discussed. A comparison between the various delamination types and the fully bonded case is presented in terms of the displacements, stresses and internal stress resultants of the faces and in the vicinity of the edges of the delaminated zones. Finally, the effect of slipping interfacial layers, with or without contact when subjected to a distributed load, is considered and compared with the behavior of a fully bonded sandwich panel. From the numerical studies it is found that the membrane action of the face sheets plays a major role in the overall structural resistance of the sandwich panel compared to that of flat panels. However, in the near vicinity of the edges of the debonded zone, the membrane action does not prevent the interfacial stresses to reach very large values in the case of delamination without contact. For all of the delamination types, contact exerts a favorable effect, in the sense that the induced interfacial stresses are much smaller when compared to cases of delamination without contact.

Get full access to this article

View all access options for this article.

References

1. Plantema, F.J. (1966). Sandwich Construction, John Wiley & Sons, New York .

2. Allen, H.G. (1969). Analysis and Design of Structural Sandwich Panels, Pergamon Press, Oxford .

3. Zenkert, D. (1995). An Introduction to Sandwich Construction, Chameleon Press Ltd., London .

4. Vinson J.R. (1999). The Behavior of Sandwich Structures of Isotropic and Composite Materials, Technomic Publishing Co. Inc., Lancaster .

5. Noor, A.K., Burton, W. S. and Bert, C.W. (1996). Computational Models for Sandwich Panels and Shells , Applied Mechanics Review, 49: 155–199 .

6. Librescu, L. and Hause, T. (2000). Recent Developments in the Modeling and Behavior of Advanced Sandwich Constructions: A Survey , Composite Structures, 48(1): 1–17 .

7. Librescu, L., Lin, W., Nemeth, M.P. and Starnes, J.H. (1994). ‘‘Effects of Tangential Edge Constraints on the Post-Buckling Behavior of Flat and Curved Panels Subjected to Thermal and Mechanical Loads’’ , In: Buckling and Postbuckling of Composite Structures, Proc. of the 1994 International Mechanical Engineering Congress, Nov. 6–11, Chicago, U.S.A., Vol. 41, pp. 55–71 .

8. Vaswani, J., Asnani, N.T. and Nakra, B.C. (1988). Vibration and Damping Analysis of Curved Sandwich Beams with a Viscoelastic Core , Composite Structures, 10(3): 231–245 .

9. Di Sciuva, M. and Carrera, E. (1990). Static Buckling of Moderately Thick, Anisotropic, Laminated and Sandwich Cylindrical Shell Panels . AIAA Journal, 28(10): 1783–1793 .

10.

10. Rao, K. M. and Meyer-Piening, H.R. (1990). Buckling Analysis of FRP Faced Cylindrical Sandwich Panel under Combined Loading , Composite Structures, 14: 15–34 .

11.

11. Hildebrand, M., On the Bending and Transverse Shearing Behavior of Curved Sandwich Panels, Technical Research Center of Finland, RN 1249, 1991.

12.

12. Smidt, S. (1995). Bending of Curved Sandwich Beams , Composite Structures, 33: 211–225 .

13.

13. Tolf, G. (1983). Stresses in a Curved Laminated Beam , Fibers Science and Technology, 19(4): 243–267 .

14.

14. Kant, T. and Kommineni, J.R. (1992). Geometrically Non-Linear Analysis of Doubly Curved Laminated and Sandwich Fiber Reinforced Composite Shells with a Higher Order Theory and C 0 Finite Elements , Journal of Reinforced Plastics and Composite Materials, 11(19): 1048–1076 .

15.

15. Kuhhorn, A. and Schoop, H. (1992). A Nonlinear Theory for Sandwich Shells Including the Wrinkling Phenomena , Archive Applied Mechanics, 62: 413–427 .

16.

16. Frostig, Y., Baruch, M., Vilnai, O. and Sheinman, I. (May 1992). High-Order Theory for Sandwich-Beam Bending with Transversely Flexible Core , Journal of ASCE, EM Division, 118(5): 1026–1043 .

17.

17. Bozhevolnaya, E. and Frostig, Y. (1997). Nonlinear Closed-Form High-Order Analysis of Curved Sandwich Panels , Composite Structures, 38(1–4): 383–394 .

18.

18. Bozhevolnaya, E. (1998). A Theoretical and Experimental Study of Shallow Sandwich Panels, Ph.D. Thesis, Institute of Mechanical Engineering, Aalborg University, Denmark.

19.

19. Karyadi, E. (1998). Collapse Behavior of Imperfect Sandwich Cylindrical Shells, Ph. D. Thesis, Delft University of Technology, Faculty of Aerospace Engineering, The Netherlands.

20.

20. Frostig, Y. (January 1999). Bending of Curved Sandwich Panels with Transversely Flexible Cores – Closed-Form High-Order Theory , Journal of Sandwich Structures & Materials, 1: 4–41 .

21.

21. Bozhevolnaya, E. and Frostig, Y. Free Vibration of Curved Sandwich Beams with a Transversely Flexible Core , Journal of Sandwich Structures and Materials (in press).

22.

22. Thomsen, O.T. and Vinson, J.R. (July 2001). Analysis and Parametric Study of Non-Circular Pressurized Sandwich Fuselage Cross Section using High-Order Sandwich Theory Formulation , Journal of Sandwich Structures and Materials, 3(3).

23.

23. Somers, M., Weller, T. and Abramovich, H. (1991). Influence of Predetermined Delaminations on Buckling and Postbuckling Behavior of Composite Sandwich Beams , Composite Structures 17(4): 295–329 .

24.

24. Hwu, C. and Hu, J.S. (1992). Buckling and Postbuckling of Delaminated Composite Sandwich Beams , AIAA Journal, 30(7): 1901–1909 .

25.

25. Simitses, G.J., Sallam, S. and Yin, W.L. (1985). Effect of Delamination of Axially Loaded Homogeneous Laminated Plates , AIAA Journal, 23(9): 1437–1444 .

26.

26. Lin, C.C., Cheng, S.H. and Wang, J.T.S. (1996). Local Buckling of Delaminated Composite Sandwich Plates , AIAA Journal, 34(10): 2176–2183 .

27.

27. Avery, J.L., Manickam N. and Sankar, B.V. Compressive Failure of Debonded Sandwich Beams . In: Sankar, B.V. (Ed.), Proceedings of the 1998 ASME International Mechanical Engineering Congress and Exposition. AD-Vol. 56, Recent Advances in Mechanics of Aerospace Structures and Materials, pp. 207–217 . ASME, New York.

28.

28. Kardomateas, G.A. Growth of Face-Sheet Delaminations in Sandwich Beams Under Compression or Bending . In: Sankar, B.V. (Ed.), Proceedings of the 1998 ASME International Mechanical Engineering Congress and Exposition. AD-Vol. 56, Recent Advances in Mechanics of Aerospace Structures and Materials, pp. 173–180 . ASME, New York.

29.

29. Zenkert, D. (1991). Strength of Sandwich Beams with Interface Debondings , Composite Structures, 17(4): 331–350 .

30.

30. Frostig, Y. (Jan. 1992). Behavior of Delaminated Sandwich Beams with Transversely Flexible Core–High Order Theory , Composite Structures Journal, 20: 116-116 .

31.

31. Frostig, Y. and Sokolinsky, V. (November 2000). High-Order Buckling of Debonded (Delaminated) Sandwich Panels with a ‘‘Soft’’ Core , AIAA Journal, 38(11): 2147–2159 .

32.

32. Rabinovitch, O. and Frostig, Y. High-Order Behavior of Fully and Partially Bonded (Delaminated) Circular Sandwich Plates with Generally Laminated Face sheets and a ‘‘Soft’’ Core , Journal of Solid and Structures (in press).

33.

33. Rabinovitch, O. and Frostig, Y. (April 2001). Non-linear High Order Analysis of Cracked RC Beams Externally Strengthened with FRP Strips , ASCE Journal of Structural Engineering, 127(4): 381–389 .