Predictions for the Increase in Pressure and Water Content of Vacuum Insulation Panels (VIPs) Integrated into Building Constructions using Model Calculations

Abstract

The climatic conditions (temperature, relative humidity, and water vapor pressure) on both sides of vacuum insulation panels (VIPs) that were integrated into different building constructions are measured every hour. The influence of these conditions on the increase in air pressure and water content within the VIPs is estimated using a calculation model. The results of these model calculations are correlated with the pressure and mass measurements on VIPs, exposed to actual climate but removed for laboratory measurements. First, we find that upon use of the temperature-dependent air permeation rates for VIPs, the linear increase within the VIPs can be predicted reliably. Thus, it is sufficient to use annual average temperatures for these estimates. Second, the mass increase of VIPs due to infusion of water vapor through the barrier foil can be determined using the calculation model. The ‘driving’ force in this case is the difference in vapor pressure across the foil cover, which decreases with time, once the water vapor pressure within the VIP starts increasing. In effect, the water vapor pressure and the water content within the VIPs reach equilibrium. Depending on the climatic conditions, the maximum water content between 3 and 7 m% can be predicted.

Keywords

vacuum insulation panel climate increase in pressure increase in water content building construction influence of humidity and temperature

Get full access to this article

View all access options for this article.

References

Schwab, H. (2001). Praxiserfahrung mit Vakuumdammungen, In: Proceedings Energieeffizienz im Bauwesen, Wurzburg, pp. 25-35.

Heinemann, U. , Caps, R. and Fricke, J. (1999). Characterization and Optimization of Filler Materials for Vacuum Super Insulations , Vuoto scienza et tecnologia, 28(1-2): 43-46 .

Schwab, H., Wachtel, J., Scheurpflug, H., Stark, C., Heinemann, U., Ebert, H.-P. and Fricke, J. (2004). Entwicklung und Anwendung von evakuierten hochsteffizienten Dammungen furGebaude (Vakuumdammung furGebaude), Project-final-report, Homepage ZAE Bayern (www.zae-bayern.de/a2/deutsch/projekte_vip/d_vakuum_start.html).

Caps, R. , Heinemann, U. , Ehrmanntraut, M. and Fricke, J. (2001). Evacuated Insulation Panels Filled with Pyrogenic Silica Powders-Properties and Application , High-Temperatures-High Pressures, 33: 151-156 .

Brunner, S. and Simmler, H. (2003). Development of Service Life Prediction Models for Vacuum Insulation Panels , In: CISBAT Conference Proceedings, Lausanne.

Schwab, H. , Heinemann, U. , Ebert, H.-P. and Fricke, J. (2005). Increase in Pressure and Mass of Foil-covered Vacuum Insulation Panels , Thermal Envelope and Building Science (to be published).

Schwab, H. , Heinemann, U. , Ebert, H.-P. and Fricke, J. (2005). Dependence of the Thermal Conductivity of Vaccum Insulation Panels with Fumed Silica Kernels on Water Content , Thermal Envelope and Building Science, 28(4): 319-326 .

Schwab, H. , Heinemann, U. , Ebert, H.-P. and Fricke, J. (2005). Prediction of Service Life for Vacuum Insulation Panels with Fumed Silica Kernel and Foil Cover , Thermal Envelope and Building Science, 28(4): 357-374 .

Kunzel, H.M. (1994). Verfahren zur ein- und zweidimensionalen Berechnung des gekoppelten Warme- und Feuchtetransports in Bauteilen mit einfachen Kennwerten, Doctoral Thesis, Faculty of Bauingenieur- und Vermessungswesen at University Stuttgart.