This study reports an experimental investigation on the effect of plate curvature and circular inter-ply delamination on the completely free vibration properties of carbon fiber reinforced polymer (CFRP) plates. Impact tests on wire suspended plates were performed and variations in measured natural frequencies and modal damping are reported. Delamination clapping type contact acoustic nonlinearity (CAN) was observed in the presence of a series of higher harmonics in the vibration spectrum. These higher harmonics consisted of five to seven equally distanced peaks grouped in a frequency range of around the double of odd mode M (5,0). Modal damping was highly sensitive to delamination which caused a 33% average increase in damping loss factors. Odd mode M (3,0) was the most affected with an average increase of 51% in damping loss factor, explained by the delamination location relative to the wavelength of that mode shape. Natural frequencies were less sensitive to delamination, on average decreasing 1.0% in flat plates and increasing 3.1% in curved plates. The modal frequencies calculated from embedded fiber optic sensor (FOS) or electrical resistance strain gauge signals agreed with finite element modeling (FEM) to within a 3.1% difference for all modes considered. The damping loss factors deducted from suspended plate tests were consistent with complementary results from dynamic mechanical analysis (DMA). The measured delamination clapping CAN and its related influence on damping can serve to enhance structural health monitoring (SHM) methods.
BabaBOThoppulS (2010) An experimental investigation of free vibration response of curved sandwich beam with face/core debond. Journal of Reinforced Plastics and Composites29(21): 3208–3218. DOI: 10.1177/0731684410369721.
2.
BeaumontPWR (2020) The structural integrity of composite materials and long-life implementation of composite structures. Applied Composite Materials27(5): 449–478. DOI: 10.1007/s10443-020-09822-6.
3.
BellisarioDQuadriniFIorioL, et al. (2022) Microscopic testing of carbon fiber laminates with shape memory epoxy interlayer. Materials Today Communications32: 103854. DOI: 10.1016/j.mtcomm.2022.103854.
4.
BlanloeuilPRoseLRFVeidtM, et al. (2018) Time reversal invariance for a nonlinear scatterer exhibiting contact acoustic nonlinearity. Journal of Sound and Vibration417: 413–431. DOI: 10.1016/j.jsv.2017.12.019.
5.
BledzkiAKKesslerARikardsR, et al. (1999) Determination of elastic constants of glass/epoxy unidirectional laminates by the vibration testing of plates. Composites Science and Technology59(13): 2015–2024. DOI: 10.1016/S0266-3538(99)00059-7.
6.
BoonYDJoshiSC (2020) A review of methods for improving interlaminar interfaces and fracture toughness of laminated composites. Materials Today Communications22: 100830. DOI: 10.1016/j.mtcomm.2019.100830.
7.
CaoMSuZDengT, et al. (2021) Nonlinear pseudo-force in “breathing” delamination to generate harmonics: a mechanism and application study. International Journal of Mechanical Sciences192: 106124. DOI: 10.1016/j.ijmecsci.2020.106124.
8.
CardenEPFanningP (2004) Vibration based condition monitoring: a review. Structural Health Monitoring3(4): 355–377. DOI: 10.1177/1475921704047500.
9.
CarfagniMLenziEPieriniM (1998) The loss factor as a measure of mechanical damping. In: Proceedings of IMAC-16 Conference. Santa Barbara. Springer, 580–584.
10.
ChangTPChangHCLiuMF (2006) A finite element analysis on random vibration of nonlinear shell structures. Journal of Sound and Vibration291(1–2): 240–257. DOI: 10.1016/j.jsv.2005.06.004.
11.
ChattopadhyayAKimHSGhoshalA (2004) Non-linear vibration analysis of smart composite structures with discrete delamination using a refined layerwise theory. Journal of Sound and Vibration273(1–2): 387–407. DOI: 10.1016/S0022-460X(03)00561-3.
12.
ChoiD-KAnH-JLeeS-Y, et al. (2022) Fluid–structure interaction analysis of a fabric skin for fabric-covered wind turbine blades. International Journal of Aeronautical and Space Sciences23(1): 92–101. DOI: 10.1007/s42405-021-00419-2.
13.
ChungKSeferisJCNamJD (2000) Investigation of thermal degradation behavior of polymeric composites: prediction of thermal cycling effect from isothermal data. Composites Part A: Applied Science and Manufacturing31(9): 945–957. DOI: 10.1016/S1359-835X(00)00043-9.
14.
ColaçoAAlves CostaPAmado-MendesP, et al. (2021) Vibrations induced by railway traffic in buildings: experimental validation of a sub-structuring methodology based on 2.5D FEM-MFS and 3D FEM. Engineering Structures240: 112381. DOI: 10.1016/j.engstruct.2021.112381.
15.
CostamilanELöwAMAwruchMDde F, et al. (2021) Experimental damping ratio evaluation using Hilbert transform in filament-wound composite plates. Polymers and Polymer Composites29(9_suppl): S1578–S1587. DOI: 10.1177/09673911211002063.
16.
DandeHA (2010) Panel Damping Loss Factor Estimation Using the Random Decrement Technique. Lawrence, KS: University of Kansas.
17.
DellaCNShuD (2005) Vibration of beams with double delaminations. Journal of Sound and Vibration282(3–5): 919–935. DOI: 10.1016/j.jsv.2004.03.052.
18.
DellaCNShuD (2007) Vibration of delaminated composite laminates: a review. Applied Mechanics Reviews60(1–6): 1–20. DOI: 10.1115/1.2375141.
19.
DelrueSVan Den AbeeleK (2012) Three-dimensional finite element simulation of closed delaminations in composite materials. Ultrasonics52(2): 315–324. DOI: 10.1016/j.ultras.2011.09.001.
20.
EsmaeeliRAliniagerdroudbariHHashemiSR, et al. (2019) Designing a New dynamic mechanical analysis (DMA) system for testing viscoelastic materials at high frequencies. Modelling and Simulation in Engineering. 2019: 7026267. DOI: 10.1155/2019/7026267.
21.
EtaatiAMehdizadehSAWangH, et al. (2014) Vibration damping characteristics of short hemp fibre thermoplastic composites. Journal of Reinforced Plastics and Composites33(4): 330–341. DOI: 10.1177/0731684413512228.
22.
FanWQiaoP (2011) Vibration-based damage identification methods: a review and comparative study. Structural Health Monitoring10(1): 83–111. DOI: 10.1177/1475921710365419.
23.
FengJYuHMaS, et al. (2022) Influence of defects on the static and dynamic buckling behavior of single-wall carbon nanotubes via molecular dynamics method. Materials Today Communications31: 103713. DOI: 10.1016/j.mtcomm.2022.103713.
24.
GoertzenWKKesslerMR (2007) Dynamic mechanical analysis of carbon/epoxy composites for structural pipeline repair. Composites Part B: Engineering38(1): 1–9. DOI: 10.1016/j.compositesb.2006.06.002.
25.
GormanDJ (1993) Accurate free vibration analysis of the completely free orthotropic rectangular plate by the method of superposition. Journal of Sound and Vibration165: 409–420. DOI: 10.1006/jsvi.1993.1267.
26.
GormanDJ (2005) Highly accurate free vibration eigenvalues for the completely free orthotropic plate. Journal of Sound and Vibration280(3–5): 1095–1115. DOI: 10.1016/j.jsv.2004.02.030.
27.
GormanDJDingW (1996) Accurate free vibration analysis of the completely free rectangular mindlin plate. Journal of Sound and Vibration189(3): 341–353. DOI: 10.1006/jsvi.1996.0023.
28.
GunasekaranVPitchaimaniJMailan ChinnapandiLB (2020) Analytical investigation on free vibration frequencies of polymer nano composite plate: effect of graphene grading and non-uniform edge loading. Materials Today Communications24: 100910. DOI: 10.1016/j.mtcomm.2020.100910.
29.
HanSYuW-R (2023) Effect of interfacial properties on the damping performance of steel–polymer sandwich cantilever beam composites. Journal of Vibration and Control29(1–2): 400–410. DOI: 10.1177/10775463211048269.
30.
HeYXiaoYSuZ, et al. (2022) Contact acoustic nonlinearity effect on the vibro-acoustic modulation of delaminated composite structures. Mechanical Systems and Signal Processing163: 108161. DOI: 10.1016/j.ymssp.2021.108161.
31.
HerSCLaiCY (2013) Dynamic behavior of nanocomposites reinforced with multi-walled carbon nanotubes (MWCNTs). Materials6(6): 2274–2284. DOI: 10.3390/ma6062274.
32.
HirwaniCKPandaSK (2019) Nonlinear thermal free vibration frequency analysis of delaminated shell panel using FEM. Composite Structures224: 111011. DOI: 10.1016/j.compstruct.2019.111011.
33.
HirwaniCKPatilRKPandaSK, et al. (2016) Experimental and numerical analysis of free vibration of delaminated curved panel. Aerospace Science and Technology54: 353–370. DOI: 10.1016/j.ast.2016.05.009.
34.
HondaSNaritaY (2012) Natural frequencies and vibration modes of laminated composite plates reinforced with arbitrary curvilinear fiber shape paths. Journal of Sound and Vibration331(1): 180–191. DOI: 10.1016/j.jsv.2011.08.019.
35.
HurlebausSGaulLWangJS (2001) An exact series solution for calculating the eigenfrequencies of orthotropic plates with completely free boundary. Journal of Sound and Vibration244(5): 747–759. DOI: 10.1006/jsvi.2000.3541.
36.
HwangSFChangCS (2000) Determination of elastic constants of materials by vibration testing. Composite Structures49(2): 183–190. DOI: 10.1016/S0263-8223(99)00132-4.
37.
IhesiulorOKShankarKZhangZ, et al. (2014) Delamination detection with error and noise polluted natural frequencies using computational intelligence concepts. Composites Part B: Engineering56: 906–925. DOI: 10.1016/j.compositesb.2013.09.032.
38.
JoglekarDM (2020) Analysis of nonlinear frequency mixing in Timoshenko beams with a breathing crack using wavelet spectral finite element method. Journal of Sound and Vibration488: 115532. DOI: 10.1016/j.jsv.2020.115532.
39.
JonesRGaleaS (2002) Health monitoring of composite repairs and joints using optical fibres. Composite Structures58(3): 397–403. DOI: 10.1016/S0263-8223(02)00235-0.
40.
JooY-SLeeJ-C (2021) Vibration fatigue analysis for structural durability evaluation under vibratory loads. International Journal of Aeronautical and Space Sciences22(3): 578–589. DOI: 10.1007/s42405-020-00326-y.
41.
JuFLeeHPLeeKH (1995) Free vibration of composite plates with delaminations around cutouts. Composite Structures31(2): 177–183. DOI: 10.1016/0263-8223(95)00016-X.
42.
JuhászZSzekrényesA (2020) An analytical solution for buckling and vibration of delaminated composite spherical shells. Thin-Walled Structures148: 106563. DOI: 10.1016/j.tws.2019.106563.
43.
KaraMGülerSSecginA (2021) Sensitivity analysis of laminated composite plates with different orientations in low to high order modes. Smart Materials and Structures30(8): 085034. DOI: 10.1088/1361-665X/ac0f46.
44.
KeleshteriMMJelovicaJ (2022) Analytical solution for vibration and buckling of cylindrical sandwich panels with improved FG metal foam core. Engineering Structures266: 114580. DOI: 10.1016/j.engstruct.2022.114580.
45.
KhanSULiCYSiddiquiNA, et al. (2011) Vibration damping characteristics of carbon fiber-reinforced composites containing multi-walled carbon nanotubes. Composites Science and Technology71(12): 1486–1494. DOI: 10.1016/j.compscitech.2011.03.022.
46.
KimSWKimEHRimMS, et al. (2011) Structural performance tests of down scaled composite wind turbine blade using embedded fiber Bragg grating sensors. International Journal of Aeronautical and Space Sciences12(4): 346–353. DOI: 10.5139/IJASS.2011.12.4.346.
47.
LeissaAW (1973) The free vibration of rectangular plates. Journal of Sound and Vibration31(3): 257–293. DOI: 10.1016/S0022-460X(73)80371-2.
48.
LiN (1992) The reciprocal theorem method for the free vibration analysis of plates: the completely free plate. Journal of Sound and Vibration157(2): 357–364. DOI: 10.1016/0022-460X(92)90687-S.
49.
LiuPSohnH (2017) Damage detection using sideband peak count in spectral correlation domain. Journal of Sound and Vibration411: 20–33. DOI: 10.1016/j.jsv.2017.08.049.
50.
MarjanovićMVuksanovićD (2014) Layerwise solution of free vibrations and buckling of laminated composite and sandwich plates with embedded delaminations. Composite Structures108(1): 9–20. DOI: 10.1016/j.compstruct.2013.09.006.
51.
MashatDSCarreraEZenkourAM, et al. (2013) Axiomatic/asymptotic evaluation of multilayered plate theories by using single and multi-points error criteria. Composite Structures106: 393–406. DOI: 10.1016/j.compstruct.2013.05.047.
52.
MeloJDDRadfordDW (2005) Time and temperature dependence of the viscoelastic properties of CFRP by dynamic mechanical analysis. Composite Structures70(2): 240–253. DOI: 10.1016/j.compstruct.2004.08.025.
53.
MondalSRamachandraLS (2019) Dynamic instability of damped composite plates with embedded delaminations. Journal of Sound and Vibration455: 221–240. DOI: 10.1016/j.jsv.2019.05.014.
54.
MontalvãoDRibeiroAMRDuarte-SilvaJ (2009) A method for the localization of damage in a CFRP plate using damping. Mechanical Systems and Signal Processing23(6): 1846–1854. DOI: 10.1016/j.ymssp.2008.08.011.
55.
NandaNSahuSK (2012) Free vibration analysis of delaminated composite shells using different shell theories. International Journal of Pressure Vessels and Piping98: 111–118. DOI: 10.1016/j.ijpvp.2012.07.008.
OrafaAHJaliliMMFotuhiAR (2023) Nonlinear analysis of sound transmission loss through cylindrical shell considering companion modes. Journal of Vibration and Control. DOI: 10.1177/10775463231203442.
58.
OvesyHRAsghari MooneghiMKharaziM (2015) Post-buckling analysis of delaminated composite laminates with multiple through-the-width delaminations using a novel layerwise theory. Thin-Walled Structures94: 98–106. DOI: 10.1016/j.tws.2015.03.028.
59.
PaixãoJda SilvaSFigueiredoE, et al. (2021) Delamination area quantification in composite structures using Gaussian process regression and auto-regressive models. Journal of Vibration and Control27(23–24): 2778–2792. DOI: 10.1177/1077546320966183.
60.
PandaHSSahuSKParhiPK (2014) Effects of moisture on the frequencies of vibration of woven fibre composite doubly curved panels with strip delaminations. Thin-Walled Structures78: 79–86. DOI: 10.1016/j.tws.2014.01.010.
61.
PandaHSSahuSKParhiPK, et al. (2015) Vibration of woven fiber composite doubly curved panels with strip delamination in thermal field. Journal of Vibration and Control21(15): 3072–3089. DOI: 10.1177/1077546313520024.
62.
PaolozziAPeroniI (1990) Detection of debonding damage in a composite plate through natural frequency variations. Journal of Reinforced Plastics and Composites9(4): 369–389. DOI: 10.1177/073168449000900405.
63.
PapagiannopoulosGAHatzigeorgiouGD (2011) On the use of the half-power bandwidth method to estimate damping in building structures. Soil Dynamics and Earthquake Engineering31(7): 1075–1079. DOI: 10.1016/j.soildyn.2011.02.007.
64.
PatnaikSSRoyT (2021) Vibration characteristics and damping properties of functionally graded carbon nanotubes reinforced hybrid composite skewed shell structures under hygrothermal conditions. Journal of Vibration and Control27(21–22): 2494–2512. DOI: 10.1177/1077546320961718.
65.
PereiraDAGuimarãesTAMResendeHB, et al. (2020) Numerical and experimental analyses of modal frequency and damping in tow-steered CFRP laminates. Composite Structures244: 112190. DOI: 10.1016/j.compstruct.2020.112190.
66.
PlacetVFoltêteE (2010) Is dynamic mechanical analysis (DMA) a non-resonance technique?EPJ Web of Conferences6: 41004. DOI: 10.1051/epjconf/20100641004.
67.
PraticòLGalosJCestinoE, et al. (2020) Experimental and numerical vibration analysis of plates with curvilinear sub-stiffeners. Engineering Structures209: 109956. DOI: 10.1016/j.engstruct.2019.109956.
RasaA (2014) Applying dynamic mechanical analysis to research & development for viscoelastic damping materials. inter.noise 2014, 43rd International Congress on Noise Control Engineering. Melbourne: Australian Acoustical Society, 1–10.
70.
RoyRParkY-BKweonJ-H, et al. (2013) Experimental testing of curved aluminum honeycomb/CFRP sandwich panels. Composites Research26(2): 85–90. DOI: 10.7234/composres.2013.26.2.085.
71.
RueppelMRionJDransfeldC, et al. (2017) Damping of carbon fibre and flax fibre angle-ply composite laminates. Composites Science and Technology146: 1–9. DOI: 10.1016/j.compscitech.2017.04.011.
72.
SaidiARBahaadiniRMajidi-MozafariK (2019) On vibration and stability analysis of porous plates reinforced by graphene platelets under aerodynamical loading. Composites Part B: Engineering164: 778–799. DOI: 10.1016/j.compositesb.2019.01.074.
73.
SargianisJSuhrJ (2012) Effect of core thickness on wave number and damping properties in sandwich composites. Composites Science and Technology72(6): 724–730. DOI: 10.1016/j.compscitech.2012.01.024.
74.
SayyadASGhugalYM (2017) Bending, buckling and free vibration of laminated composite and sandwich beams: a critical review of literature. Composite Structures171: 486–504. DOI: 10.1016/j.compstruct.2017.03.053.
75.
SecginAGulerSKaraM (2016) Determinations of in-situ energy loss factors of point-connected composite plates. Composites Part B: Engineering87: 27–32. Doi: 10.1016/j.compositesb.2015.09.019.
76.
SegersJHedayatrasaSPoelmanG, et al. (2020) Backside delamination detection in composites through local defect resonance induced nonlinear source behavior. Journal of Sound and Vibration479: 115360. DOI: 10.1016/j.jsv.2020.115360.
77.
SepehryNEhsaniMZhuW, et al. (2021) Application of scaled boundary finite element method for vibration-based structural health monitoring of breathing cracks. Journal of Vibration and Control27(23–24): 2870–2886. DOI: 10.1177/1077546320968646.
78.
SessnerVLiebigWVJackstadtA, et al. (2021) Wide Scale Characterization and Modeling of the Vibration and Damping Behavior of CFRP-Elastomer-Metal Laminates—Comparison and Discussion of Different Test Setups. Netherlands: Springer. DOI: 10.1007/s10443-021-09934-7.
79.
ShankarGKeshava KumarSMahatoPK (2017) Vibration analysis and control of smart composite plates with delamination and under hygrothermal environment. Thin-Walled Structures116: 53–68. DOI: 10.1016/j.tws.2017.03.013.
80.
Shariati NiaMTorabiKHeidari-RaraniM (2014) Free vibration analysis of a composite beam with single delamination- an improved free and constrained model. Engineering Solid Mechanics2(4): 313–320. DOI: 10.5267/j.esm.2014.7.002.
81.
SharmaMVaishR (2020) Vibration energy harvesting for degradation of dye and bacterial cells using cement-based Ba0.85Ca0.15Zr0.1Ti0.90O3 composites. Materials Today Communications25: 101592. DOI: 10.1016/j.mtcomm.2020.101592.
82.
ShenYTanJFernandesL, et al. (2019) Dynamic mechanical analysis on delaminated flax fiber reinforced composites. Materials12(16): 2559. DOI: 10.3390/ma12162559.
83.
ShishirMARZhangZCaiD, et al. (2023) Free vibration analysis of polymer pin-reinforced foam core sandwich composite panels. Journal of Reinforced Plastics and Composites42(3–4): 163–176. DOI: 10.1177/07316844221105287.
84.
SinghaTDRoutMBandyopadhyayT, et al. (2020) Free vibration analysis of rotating pretwisted composite sandwich conical shells with multiple debonding in hygrothermal environment. Engineering Structures204: 110058. DOI: 10.1016/j.engstruct.2019.110058.
85.
SoleimanpourRNgCT (2022) Scattering analysis of nonlinear Lamb waves at delaminations in composite laminates. Journal of Vibration and Control28(11–12): 1311–1323. DOI: 10.1177/1077546321990145.
86.
SoleimanpourRNgCTWangCH (2017) Higher harmonic generation of guided waves at delaminations in laminated composite beams. Structural Health Monitoring16(4): 400–417. DOI: 10.1177/1475921716673021.
SubramaniMRamamoorthyM (2020) Vibration analysis of multiwalled carbon nanotube-reinforced composite shell: an experimental study. Polymers and Polymer Composites28(4): 223–232. DOI: 10.1177/0967391119870406.
89.
ThomasBRoyT (2017) Vibration and damping analysis of functionally graded carbon nanotubes reinforced hybrid composite shell structures. Journal of Vibration and Control23(11): 1711–1738. DOI: 10.1177/1077546315599680.
90.
TianYShenYRaoD, et al. (2019) Metamaterial improved nonlinear ultrasonics for fatigue damage detection. Smart Materials and Structures28(7): 075038. DOI: 10.1088/1361-665X/ab2566.
91.
TianYKimWKowalskiE, et al. (2022) Damping of micro- and nanocellulose reinforced PA610 composites and influences of moisture absorption. Materials Today Communications33: 104325. DOI: 10.1016/j.mtcomm.2022.104325.
92.
TorabiARShamsSFatehiNM, et al. (2022) Delamination effects on the unsteady aero-elastic behavior of composite wing by modal analysis. Journal of Vibration and Control28(19–20): 2732–2745. DOI: 10.1177/10775463211019213.
93.
TrevisoAVan GenechtenBMundoD, et al. (2015) Damping in composite materials: properties and models. Composites Part B: Engineering78: 144–152. DOI: 10.1016/j.compositesb.2015.03.081.
94.
WangCLiCXuF, et al. (2012) Research on the predict method of random vibration cumulative fatigue damage life based on the finite element analysis. International Journal of Mechanical, Aerospace, Industrial, Mechatronic and Manufacturing Engineering6(12): 2686–2690. DOI: 10.4028/www.scientific.net/AMM.300-301.992.
95.
WeiLChenJ (2022) Characterization of delamination features of orthotropic CFRP laminates using higher harmonic generation technique: experimental and numerical studies. Composite Structures285: 115239. DOI: 10.1016/j.compstruct.2022.115239.
96.
WeiZYamLHChengL (2005) Delamination assessment of multilayer composite plates using model-based neural networks. Journal of Vibration and Control11(5): 607–625. DOI: 10.1177/1077546305052317.
97.
XuCRongDZhouZ, et al. (2020) Vibration and buckling characteristics of cracked natural fiber reinforced composite plates with corner point-supports. Engineering Structures214: 110614. DOI: 10.1016/j.engstruct.2020.110614.
98.
YelveNPMitraMMujumdarPM (2017) Detection of delamination in composite laminates using Lamb wave based nonlinear method. Composite Structures159: 257–266. DOI: 10.1016/j.compstruct.2016.09.073.
99.
YeniYNChristophersonGTTurnerAS, et al. (2004) Apparent viscoelastic anisotropy as measured from nondestructive oscillatory tests can reflect the presence of a flaw in cortical bone. Journal of Biomedical Materials Research Part A69(1): 124–130. DOI: 10.1002/jbm.a.20128.
100.
YimJH (1997) Damping in partially delaminated composites. KSME International Journal11(5): 537–546. DOI: 10.1007/BF02945266.
101.
ZhangZShankarKTahtaliMMorozovV, et al. (2010) Vibration modelling of composite laminates with delamination damage. ICA 2010, 20th International Congress on Acoustics. Sydney: Australian Acoustical Society, 1–8.
102.
ZhangZShankarKMorozovEV, et al. (2016) Vibration-based delamination detection in composite beams through frequency changes. Journal of Vibration and Control22(2): 496–512. DOI: 10.1177/1077546314533584.
103.
ZhangZPanJLuoW, et al. (2019) Vibration-based delamination detection in curved composite plates. Composites Part A: Applied Science and Manufacturing119: 261–274. DOI: 10.1016/j.compositesa.2019.02.002.
